149 lines
5.0 KiB
Makefile
149 lines
5.0 KiB
Makefile
# Target file name (without extension).
|
|
TARGET ?= 108
|
|
|
|
# Directory common source filess exist
|
|
TMK_DIR ?= ../../tmk_core
|
|
|
|
# Directory keyboard dependent files exist
|
|
TARGET_DIR ?= .
|
|
|
|
# project specific files
|
|
SRC ?= keymap_108.c \
|
|
matrix.c \
|
|
led.c
|
|
|
|
CONFIG_H ?= config.h
|
|
|
|
|
|
# MCU name
|
|
MCU ?= atmega32
|
|
|
|
# Defines needed to use correct registers for the atmega32
|
|
OPT_DEFS += -DNO_CLKPR -DTIMER0_COMP -DTIMER_PRESCALER=1024
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
F_CPU ?= 16000000
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB ?= $(F_CPU)
|
|
|
|
# Interrupt driven control endpoint task(+60)
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
|
|
# Boot Section Size in *bytes*
|
|
# Teensy halfKay 512
|
|
# Teensy++ halfKay 1024
|
|
# Atmel DFU loader 4096
|
|
# LUFA bootloader 4096
|
|
# USBaspLoader 2048
|
|
BOOTLOADER_SIZE ?= 2048
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
|
|
|
|
|
|
# Build Options
|
|
# comment out to disable the options.
|
|
#
|
|
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
|
|
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
|
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
|
CONSOLE_ENABLE ?= no # Console for debug disabled, disables also UART RX
|
|
COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
|
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
|
|
NKRO_ENABLE ?= no # USB Nkey Rollover
|
|
ACTIONMAP_ENABLE ?= no # Use 16bit action codes in keymap instead of 8bit keycodes
|
|
NO_UART = yes # UART for debugging
|
|
|
|
|
|
# Optimize size but this may cause error "relocation truncated to fit"
|
|
#EXTRALDFLAGS = -Wl,--relax
|
|
|
|
# Search Path
|
|
VPATH += $(TARGET_DIR)
|
|
VPATH += $(TMK_DIR)
|
|
|
|
include $(TMK_DIR)/protocol.mk
|
|
include $(TMK_DIR)/common.mk
|
|
include $(TMK_DIR)/protocol/vusb.mk
|
|
include $(TMK_DIR)/rules.mk
|
|
|
|
|
|
#---------------- Programming Options (avrdude) ----------------
|
|
|
|
AVRDUDE ?= avrdude
|
|
|
|
# Programming hardware, type: avrdude -c ?
|
|
# to get a full listing.
|
|
#
|
|
# This setting asumes, that you flashed the bootloader first
|
|
AVRDUDE_PROGRAMMER ?= usbasp
|
|
|
|
# com1 = serial port. Use lpt1 to connect to parallel port.
|
|
AVRDUDE_PORT ?= /dev/ttyACM0 # programmer connected to serial device
|
|
|
|
AVRDUDE_WRITE_FLASH ?= -U flash:w:$(TARGET).hex
|
|
#AVRDUDE_WRITE_EEPROM ?= -U eeprom:w:$(TARGET).eep
|
|
|
|
# Brown-out detection level at VCC=2.7 V; [BODLEVEL=1]
|
|
# Ext. Crystal Osc.; High Frequency; Start-up time PWRDWN/RESET: 1024 clk + 64 ms; [CKSEL=1111 SUT=00]
|
|
# Boot Reset vector Enabled (Jump to bootloader first)
|
|
# Serial program downloading (SPI) enabled; [SPIEN=0]
|
|
# Watch-dog Timer disabled; [WDTON=0]
|
|
# Self Programming disabled; [SELFPRGEN=0]
|
|
AVRDUDE_FUSEBITS ?= -U lfuse:w:0x8F:m -U hfuse:w:0xC8:m
|
|
|
|
|
|
# Uncomment the following if you want avrdude's erase cycle counter.
|
|
# Note that this counter needs to be initialized first using -Yn,
|
|
# see avrdude manual.
|
|
#AVRDUDE_ERASE_COUNTER ?= -y
|
|
|
|
# Uncomment the following if you do /not/ wish a verification to be
|
|
# performed after programming the device.
|
|
#AVRDUDE_NO_VERIFY ?= -V
|
|
|
|
# Increase verbosity level. Please use this when submitting bug
|
|
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
|
|
# to submit bug reports.
|
|
#AVRDUDE_VERBOSE ?= -v -v
|
|
|
|
AVRDUDE_FLAGS ?= -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
|
|
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
|
|
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
|
|
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
|
|
|
|
#============================================================================
|
|
|
|
# Program the device.
|
|
program: $(TARGET).hex $(TARGET).eep
|
|
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) $(AVRDUDE_FUSEBITS)
|
|
|
|
# Set fuses.
|
|
fuse:
|
|
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_FUSEBITS)
|
|
|
|
# Listing of phony targets.
|
|
.PHONY : all sizebefore sizeafter gccversion \
|
|
build elf hex eep lss sym coff extcoff \
|
|
clean program fuse
|