|
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141 |
- #----------------------------------------------------------------------------
- # On command line:
- #
- # make all = Make software.
- #
- # make clean = Clean out built project files.
- #
- # make coff = Convert ELF to AVR COFF.
- #
- # make extcoff = Convert ELF to AVR Extended COFF.
- #
- # make program = Download the hex file to the device.
- # Please customize your programmer settings(PROGRAM_CMD)
- #
- # make teensy = Download the hex file to the device, using teensy_loader_cli.
- # (must have teensy_loader_cli installed).
- #
- # make dfu = Download the hex file to the device, using dfu-programmer (must
- # have dfu-programmer installed).
- #
- # make flip = Download the hex file to the device, using Atmel FLIP (must
- # have Atmel FLIP installed).
- #
- # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
- # (must have dfu-programmer installed).
- #
- # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
- # (must have Atmel FLIP installed).
- #
- # make debug = Start either simulavr or avarice as specified for debugging,
- # with avr-gdb or avr-insight as the front end for debugging.
- #
- # make filename.s = Just compile filename.c into the assembler code only.
- #
- # make filename.i = Create a preprocessed source file for use in submitting
- # bug reports to the GCC project.
- #
- # To rebuild project do "make clean" then "make all".
- #----------------------------------------------------------------------------
-
- # Target file name (without extension).
- TARGET = hhkb_lufa
-
- # Directory common source filess exist
- TOP_DIR = ../..
-
- # Directory keyboard dependent files exist
- TARGET_DIR = .
-
-
- # List C source files here. (C dependencies are automatically generated.)
- SRC += keymap_common.c \
- matrix.c \
- led.c
-
- ifdef KEYMAP
- SRC := keymap_$(KEYMAP).c $(SRC)
- else
- SRC := keymap_hasu.c $(SRC)
- endif
-
- CONFIG_H = config.h
-
-
- # MCU name
- # PJRC Teensy++ 2.0
- #MCU = at90usb1286
- # TMK Alt Controller or PJRC Teensy 2.0
- MCU = atmega32u4
-
- # Processor frequency.
- # This will define a symbol, F_CPU, in all source code files equal to the
- # processor frequency in Hz. You can then use this symbol in your source code to
- # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
- # automatically to create a 32-bit value in your source code.
- #
- # This will be an integer division of F_USB below, as it is sourced by
- # F_USB after it has run through any CPU prescalers. Note that this value
- # does not *change* the processor frequency - it should merely be updated to
- # reflect the processor speed set externally so that the code can use accurate
- # software delays.
- F_CPU = 16000000
-
-
- #
- # LUFA specific
- #
- # Target architecture (see library "Board Types" documentation).
- ARCH = AVR8
-
- # Input clock frequency.
- # This will define a symbol, F_USB, in all source code files equal to the
- # input clock frequency (before any prescaling is performed) in Hz. This value may
- # differ from F_CPU if prescaling is used on the latter, and is required as the
- # raw input clock is fed directly to the PLL sections of the AVR for high speed
- # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
- # at the end, this will be done automatically to create a 32-bit value in your
- # source code.
- #
- # If no clock division is performed on the input clock inside the AVR (via the
- # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
- F_USB = $(F_CPU)
-
- # Interrupt driven control endpoint task
- #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
- # Boot Section Size in *bytes*
- # Teensy halfKay 512
- # Teensy++ halfKay 1024
- # Atmel DFU loader 4096 (TMK Alt Controller)
- # LUFA bootloader 4096
- # USBaspLoader 2048
- OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
- # Build Options
- # comment out to disable the options.
- #
- BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
- MOUSEKEY_ENABLE = yes # Mouse keys
- EXTRAKEY_ENABLE = yes # Audio control and System control
- #CONSOLE_ENABLE = yes # Console for debug
- COMMAND_ENABLE = yes # Commands for debug and configuration
- NKRO_ENABLE = yes # USB Nkey Rollover
- KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
-
-
- # Search Path
- VPATH += $(TARGET_DIR)
- VPATH += $(TOP_DIR)
-
- include $(TOP_DIR)/protocol/lufa.mk
- include $(TOP_DIR)/common.mk
- include $(TOP_DIR)/rules.mk
-
- debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
- debug-on: all
-
- debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
- debug-off: all
|