|
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106 |
- #
- # Makefile for Teensy
- #
- # Target file name (without extension).
- TARGET = serialmouse_usb
-
- # Directory common source filess exist
- TMK_DIR = ../../tmk_core
-
- # Directory keyboard dependent files exist
- TARGET_DIR = .
-
- # project specific files
- SRC = keymap.c \
- matrix.c \
- led.c
-
- CONFIG_H = config.h
-
-
- # MCU name
- #MCU = at90usb1287
- MCU = atmega32u4
-
- # Processor frequency.
- # This will define a symbol, F_CPU, in all source code files equal to the
- # processor frequency in Hz. You can then use this symbol in your source code to
- # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
- # automatically to create a 32-bit value in your source code.
- #
- # This will be an integer division of F_USB below, as it is sourced by
- # F_USB after it has run through any CPU prescalers. Note that this value
- # does not *change* the processor frequency - it should merely be updated to
- # reflect the processor speed set externally so that the code can use accurate
- # software delays.
- F_CPU = 16000000
-
-
- #
- # LUFA specific
- #
- # Target architecture (see library "Board Types" documentation).
- ARCH = AVR8
-
- # Input clock frequency.
- # This will define a symbol, F_USB, in all source code files equal to the
- # input clock frequency (before any prescaling is performed) in Hz. This value may
- # differ from F_CPU if prescaling is used on the latter, and is required as the
- # raw input clock is fed directly to the PLL sections of the AVR for high speed
- # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
- # at the end, this will be done automatically to create a 32-bit value in your
- # source code.
- #
- # If no clock division is performed on the input clock inside the AVR (via the
- # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
- F_USB = $(F_CPU)
-
- # Interrupt driven control endpoint task(+60)
- #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
- # Boot Section Size in *bytes*
- # Teensy halfKay 512
- # Teensy++ halfKay 1024
- # Atmel DFU loader 4096
- # LUFA bootloader 4096
- # USBaspLoader 2048
- OPT_DEFS += -DBOOTLOADER_SIZE=512
-
-
- # Build Options
- # comment out to disable the options.
- #
- #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
- #MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
- #EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
- CONSOLE_ENABLE = yes # Console for debug(+400)
- #COMMAND_ENABLE = yes # Commands for debug and configuration
- #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
-
-
- # Serial Mouse Options
- # You can choose a mouse protocol and the implementation of
- # the underlying serial connection.
- #
- SERIAL_MOUSE_MICROSOFT_ENABLE = yes # Enable support for Microsoft-compatible mice
- #SERIAL_MOUSE_MOUSESYSTEMS_ENABLE = yes # Enable support for Mousesystems-compatible mice
- #SERIAL_MOUSE_USE_UART = yes # use hardware UART for serial connection
- SERIAL_MOUSE_USE_SOFT = yes # use software serial implementation
-
- # Optional serial mouse driver features
- # Support scrolling while holding the middle mouse button
- # (currently only supported for Mousesystems mice):
- #OPT_DEFS += -DSERIAL_MOUSE_CENTER_SCROLL
-
- # Optimize size but this may cause error "relocation truncated to fit"
- #EXTRALDFLAGS = -Wl,--relax
-
- # Search Path
- VPATH += $(TARGET_DIR)
- VPATH += $(TMK_DIR)
-
- include $(TMK_DIR)/protocol.mk
- include $(TMK_DIR)/protocol/lufa.mk
- include $(TMK_DIR)/common.mk
- include $(TMK_DIR)/rules.mk
|