1
0
tmk_keyboard/keyboard/onekey/Makefile.pjrc

104 lines
3.3 KiB
Makefile
Raw Normal View History

#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device.
# Please customize your programmer settings(PROGRAM_CMD)
#
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# Target file name (without extension).
TARGET = onekey_pjrc
# Directory common source filess exist
TOP_DIR = ../..
# Directory keyboard dependent files exist
TARGET_DIR = .
# project specific files
SRC = keymap.c \
matrix.c \
led.c
CONFIG_H = config.h
# MCU name, you MUST set this to match the board you are using
# type "make clean" after changing this, so all files will be rebuilt
MCU = atmega32u4
#MCU = at90usb1286
# Processor frequency.
# Normally the first thing your program should do is set the clock prescaler,
# so your program will run at the correct speed. You should also set this
# variable to same clock speed. The _delay_ms() macro uses this, and many
# examples use this variable to calculate timings. Do not add a "UL" here.
F_CPU = 16000000
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Atmel DFU loader 4096
# LUFA bootloader 4096
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
2013-11-18 18:39:15 +00:00
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
#MOUSEKEY_ENABLE = yes # Mouse keys(+5000)
#EXTRAKEY_ENABLE = yes # Audio control and System control(+600)
CONSOLE_ENABLE = yes # Console for debug
2013-11-18 18:39:15 +00:00
#COMMAND_ENABLE = yes # Commands for debug and configuration
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
#NKRO_ENABLE = yes # USB Nkey Rollover(+500)
#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support
2013-11-18 18:39:15 +00:00
#PS2_USE_BUSYWAIT = yes # uses primitive reference code
#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
#PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TOP_DIR)
include $(TOP_DIR)/common.mk
2013-11-18 18:39:15 +00:00
include $(TOP_DIR)/protocol.mk
include $(TOP_DIR)/protocol/pjrc.mk
include $(TOP_DIR)/rules.mk