1
0
tmk_keyboard/converter/usb_usb/Makefile

137 lines
4.1 KiB
Makefile
Raw Normal View History

2012-08-27 06:18:01 +00:00
#----------------------------------------------------------------------------
# On command line:
#
# make all = Make software.
#
# make clean = Clean out built project files.
#
# make coff = Convert ELF to AVR COFF.
#
# make extcoff = Convert ELF to AVR Extended COFF.
#
# make program = Download the hex file to the device.
# Please customize your programmer settings(PROGRAM_CMD)
#
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
# make dfu = Download the hex file to the device, using dfu-programmer (must
# have dfu-programmer installed).
#
# make flip = Download the hex file to the device, using Atmel FLIP (must
# have Atmel FLIP installed).
#
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
# (must have dfu-programmer installed).
#
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
# (must have Atmel FLIP installed).
#
# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
#
# make filename.i = Create a preprocessed source file for use in submitting
# bug reports to the GCC project.
#
# To rebuild project do "make clean" then "make all".
#----------------------------------------------------------------------------
# Target file name (without extension).
TARGET = usb_usb
2015-04-09 16:53:24 +00:00
TMK_DIR = ../../tmk_core
2012-08-27 06:18:01 +00:00
# Directory keyboard dependent files exist
TARGET_DIR = .
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Build Options
# comment out to disable the options.
#
MOUSEKEY_ENABLE = yes # Mouse keys
EXTRAKEY_ENABLE = yes # Media control and System control
CONSOLE_ENABLE = yes # Console for debug
#NKRO_ENABLE = yes # USB Nkey Rollover
# Boot Section Size in bytes
# Teensy halfKay 512
# Atmel DFU loader 4096
# LUFA bootloader 4096
2014-12-10 18:52:05 +00:00
OPT_DEFS += -DBOOTLOADER_SIZE=4096
2012-08-27 06:18:01 +00:00
SRC = \
2014-12-10 18:52:05 +00:00
keymap_common.c \
2012-08-27 06:18:01 +00:00
matrix.c \
led.c \
main.cpp
2014-12-10 18:52:05 +00:00
ifdef KEYMAP
SRC := keymap_$(KEYMAP).c $(SRC)
else
SRC := keymap.c $(SRC)
endif
2012-08-27 06:18:01 +00:00
CONFIG_H = config.h
# Search Path
VPATH += $(TARGET_DIR)
2015-04-09 07:20:42 +00:00
VPATH += $(TMK_DIR)
2012-08-27 06:18:01 +00:00
# program Leonardo
2014-12-10 05:35:46 +00:00
PROGRAM_CMD = avrdude -p$(MCU) -cavr109 -b57600 -Uflash:w:$(TARGET).hex -P$(DEV)
2012-08-27 06:18:01 +00:00
2015-04-09 07:20:42 +00:00
include $(TMK_DIR)/protocol/usb_hid.mk
include $(TMK_DIR)/protocol/lufa.mk
include $(TMK_DIR)/common.mk
include $(TMK_DIR)/rules.mk