@@ -1,31 +1,39 @@ | |||
# | |||
# Makefile for Teensy | |||
# | |||
# Target file name (without extension). | |||
TARGET = ps2_usb_lufa | |||
TARGET ?= ps2_usb | |||
# Directory common source filess exist | |||
TMK_DIR = ../../tmk_core | |||
TMK_DIR ?= ../../tmk_core | |||
# Directory keyboard dependent files exist | |||
TARGET_DIR = . | |||
TARGET_DIR ?= . | |||
# project specific files | |||
SRC = matrix.c \ | |||
SRC ?= matrix.c \ | |||
led.c | |||
# | |||
# Keymap file | |||
# | |||
ifdef UNIMAP_ENABLE | |||
KEYMAP_FILE = unimap | |||
else | |||
ifdef ACTIONMAP_ENABLE | |||
KEYMAP_FILE = actionmap | |||
else | |||
KEYMAP_FILE = keymap | |||
endif | |||
endif | |||
ifdef KEYMAP | |||
SRC := keymap_$(KEYMAP).c $(SRC) | |||
SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC) | |||
else | |||
SRC := keymap_plain.c $(SRC) | |||
SRC := $(KEYMAP_FILE)_plain.c $(SRC) | |||
endif | |||
CONFIG_H = config.h | |||
CONFIG_H ?= config.h | |||
# MCU name | |||
#MCU = at90usb1287 | |||
MCU = atmega32u4 | |||
MCU ?= atmega32u2 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
@@ -38,14 +46,14 @@ MCU = atmega32u4 | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
F_CPU ?= 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
ARCH ?= AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
@@ -58,7 +66,7 @@ ARCH = AVR8 | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
F_USB ?= $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
@@ -70,25 +78,26 @@ F_USB = $(F_CPU) | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
BOOTLOADER_SIZE ?= 4096 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE) | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = yes # Console for debug(+400) | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA | |||
# PS/2 Options | |||
# | |||
#PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) | |||
PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin | |||
#PS2_USE_BUSYWAIT = yes # uses primitive reference code | |||
#PS2_USE_USART ?= yes # uses hardware USART engine for PS/2 signal receive(recomened) | |||
PS2_USE_INT ?= yes # uses external interrupt for falling edge of PS/2 clock pin | |||
#PS2_USE_BUSYWAIT ?= yes # uses primitive reference code | |||
# Optimize size but this may cause error "relocation truncated to fit" |
@@ -1,74 +0,0 @@ | |||
# Target file name (without extension). | |||
TARGET = ps2_usb_pjrc | |||
# Directory common source filess exist | |||
TMK_DIR = ../../tmk_core | |||
# Directory keyboard dependent files exist | |||
TARGET_DIR = . | |||
# keyboard dependent files | |||
SRC = matrix.c \ | |||
led.c | |||
ifdef KEYMAP | |||
SRC := keymap_$(KEYMAP).c $(SRC) | |||
else | |||
SRC := keymap_plain.c $(SRC) | |||
endif | |||
CONFIG_H = config.h | |||
# MCU name, you MUST set this to match the board you are using | |||
# type "make clean" after changing this, so all files will be rebuilt | |||
#MCU = at90usb162 # Teensy 1.0 | |||
MCU = atmega32u4 # Teensy 2.0 | |||
#MCU = at90usb646 # Teensy++ 1.0 | |||
#MCU = at90usb1286 # Teensy++ 2.0 | |||
# Processor frequency. | |||
# Normally the first thing your program should do is set the clock prescaler, | |||
# so your program will run at the correct speed. You should also set this | |||
# variable to same clock speed. The _delay_ms() macro uses this, and many | |||
# examples use this variable to calculate timings. Do not add a "UL" here. | |||
F_CPU = 16000000 | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# *Comment out* to disable the options. | |||
# | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys | |||
EXTRAKEY_ENABLE = yes # Audio control and System control | |||
CONSOLE_ENABLE = yes # Console for debug(+400) | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
NKRO_ENABLE = yes # USB Nkey Rollover | |||
# PS/2 Options | |||
# | |||
#PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) | |||
#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin | |||
PS2_USE_BUSYWAIT = yes # uses primitive reference code | |||
# Search Path | |||
VPATH += $(TARGET_DIR) | |||
VPATH += $(TMK_DIR) | |||
include $(TMK_DIR)/protocol.mk | |||
include $(TMK_DIR)/protocol/pjrc.mk | |||
include $(TMK_DIR)/common.mk | |||
include $(TMK_DIR)/rules.mk |
@@ -0,0 +1,17 @@ | |||
TARGET ?= ps2_usb_rev1 | |||
MCU = atmega32u4 | |||
CONFIG_H = config_rev1.h | |||
BOOTLOADER_SIZE = 4096 | |||
BOOTMAGIC_ENABLE ?= no | |||
MOUSEKEY_ENABLE ?= yes | |||
EXTRAKEY_ENABLE ?= yes | |||
CONSOLE_ENABLE ?= yes | |||
COMMAND_ENABLE ?= yes | |||
NKRO_ENABLE ?= yes | |||
PS2_USE_USART = yes | |||
PS2_USE_INT = no | |||
PS2_USE_BUSYWAIT = no | |||
include Makefile |
@@ -0,0 +1,17 @@ | |||
TARGET ?= ps2_usb_rev2 | |||
MCU = atmega32u2 | |||
CONFIG_H = config_rev2.h | |||
BOOTLOADER_SIZE = 4096 | |||
BOOTMAGIC_ENABLE ?= no | |||
MOUSEKEY_ENABLE ?= no | |||
EXTRAKEY_ENABLE ?= yes | |||
CONSOLE_ENABLE ?= yes | |||
COMMAND_ENABLE ?= yes | |||
NKRO_ENABLE ?= yes | |||
PS2_USE_USART = no | |||
PS2_USE_INT = yes | |||
PS2_USE_BUSYWAIT = no | |||
include Makefile |
@@ -1,97 +0,0 @@ | |||
# | |||
# Makefile for TMK keyboard converter rev2 | |||
# https://github.com/tmk/keyboard_converter#pcb-rev1 | |||
# | |||
# Target file name (without extension). | |||
TARGET = ps2_usb_tmk_rev1 | |||
# Directory common source filess exist | |||
TMK_DIR = ../../tmk_core | |||
# Directory keyboard dependent files exist | |||
TARGET_DIR = . | |||
# project specific files | |||
SRC = matrix.c \ | |||
led.c | |||
ifdef KEYMAP | |||
SRC := keymap_$(KEYMAP).c $(SRC) | |||
else | |||
SRC := keymap_plain.c $(SRC) | |||
endif | |||
CONFIG_H = config_tmk_rev1.h | |||
# MCU name | |||
MCU = atmega32u4 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = yes # Console for debug(+400) | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |||
# PS/2 Options | |||
# | |||
PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) | |||
#PS2_USE_BUSYWAIT = yes # uses primitive reference code | |||
# Search Path | |||
VPATH += $(TARGET_DIR) | |||
VPATH += $(TMK_DIR) | |||
include $(TMK_DIR)/protocol.mk | |||
include $(TMK_DIR)/protocol/lufa.mk | |||
include $(TMK_DIR)/common.mk | |||
include $(TMK_DIR)/rules.mk |
@@ -1,97 +0,0 @@ | |||
# | |||
# Makefile for TMK keyboard converter rev2 | |||
# https://github.com/tmk/keyboard_converter#pcb-rev2 | |||
# | |||
# Target file name (without extension). | |||
TARGET = ps2_usb_tmk_rev2 | |||
# Directory common source filess exist | |||
TMK_DIR = ../../tmk_core | |||
# Directory keyboard dependent files exist | |||
TARGET_DIR = . | |||
# project specific files | |||
SRC = matrix.c \ | |||
led.c | |||
ifdef KEYMAP | |||
SRC := keymap_$(KEYMAP).c $(SRC) | |||
else | |||
SRC := keymap_plain.c $(SRC) | |||
endif | |||
CONFIG_H = config_tmk_rev2.h | |||
# MCU name | |||
MCU = atmega32u2 | |||
# Processor frequency. | |||
# This will define a symbol, F_CPU, in all source code files equal to the | |||
# processor frequency in Hz. You can then use this symbol in your source code to | |||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
# automatically to create a 32-bit value in your source code. | |||
# | |||
# This will be an integer division of F_USB below, as it is sourced by | |||
# F_USB after it has run through any CPU prescalers. Note that this value | |||
# does not *change* the processor frequency - it should merely be updated to | |||
# reflect the processor speed set externally so that the code can use accurate | |||
# software delays. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = yes # Console for debug(+400) | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |||
# PS/2 Options | |||
# | |||
PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin | |||
#PS2_USE_BUSYWAIT = yes # uses primitive reference code | |||
# Search Path | |||
VPATH += $(TARGET_DIR) | |||
VPATH += $(TMK_DIR) | |||
include $(TMK_DIR)/protocol.mk | |||
include $(TMK_DIR)/protocol/lufa.mk | |||
include $(TMK_DIR)/common.mk | |||
include $(TMK_DIR)/rules.mk |
@@ -0,0 +1,5 @@ | |||
TARGET = ps2_usb_rev1_unimap | |||
UNIMAP_ENABLE = yes | |||
KEYMAP_SECTION_ENABLE = yes | |||
include Makefile.rev1 |
@@ -0,0 +1,5 @@ | |||
TARGET = ps2_usb_rev2_unimap | |||
UNIMAP_ENABLE = yes | |||
KEYMAP_SECTION_ENABLE = yes | |||
include Makefile.rev2 |
@@ -5,36 +5,30 @@ This firmware converts PS/2 keyboard protocol to USB.(It supports Scan Code Set | |||
Connect Wires | |||
------------- | |||
In case of Teensy2.0(ATMega32U4): | |||
1. Connect **Vcc** and **GND**. | |||
2. Connect **Clock** and **Data** line. | |||
- **Interrupt**: **Clock** is on `PD1` and **Data** on `PD0`.(Recommended. Soarer's converter compatible) | |||
- **Busywait**: **Clock** is on `PD1` and **Data** on `PD0`. | |||
- **USART**: **Clock** is on `PD5` and **Data** on `PD2`. | |||
3. Optionally you need pull-up resistor. 1K-10K Ohm is OK. | |||
3. You need pull-up resistors. 1K-10K Ohm would be fine. | |||
To change pin configuration edit **config.h** and **Makefile**. | |||
Build Firmware | |||
-------------- | |||
For **PJRC Teensy** just run `make`: | |||
$ make clean | |||
$ make | |||
To select keymap: | |||
For **TMK converter Rev.2**: | |||
$ make clean | |||
$ make KEYMAP=[plain|jis|spacefn|...] | |||
$ make -f Makefile.rev2 clean | |||
$ make -f Makefile.rev2 KEYMAP=plain | |||
After that you will find HEX file `ps2_usb_lufa.hex` in current directory. | |||
To program firmware push the button on converter and run: | |||
$ make -f Makefile.rev2 KEYMAP=plain dfu | |||
- For **TMK converter Rev.1** use `make -f Makefile.tmk_rev1` instead of `make` and HEX file is `ps2_usb_tmk_rev1.hex`. | |||
- For **TMK converter Rev.2** use `make -f Makefile.tmk_rev2` instead of `make` and HEX file is `ps2_usb_tmk_rev2.hex`. | |||
- For **TMK converter Rev.1** use `make -f Makefile.rev1` instead. | |||
- To select keymap use `jis`, `spacefn` or your own in place of `plain`. | |||
Keymap |
@@ -0,0 +1,45 @@ | |||
/* | |||
Copyright 2016 Jun Wako <[email protected]> | |||
This program is free software: you can redistribute it and/or modify | |||
it under the terms of the GNU General Public License as published by | |||
the Free Software Foundation, either version 2 of the License, or | |||
(at your option) any later version. | |||
This program is distributed in the hope that it will be useful, | |||
but WITHOUT ANY WARRANTY; without even the implied warranty of | |||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |||
GNU General Public License for more details. | |||
You should have received a copy of the GNU General Public License | |||
along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
*/ | |||
#include "unimap_trans.h" | |||
#define AC_FN0 ACTION_LAYER_MOMENTARY(1) | |||
#ifdef KEYMAP_SECTION_ENABLE | |||
const action_t actionmaps[][UNIMAP_ROWS][UNIMAP_COLS] __attribute__ ((section (".keymap.keymaps"))) = { | |||
#else | |||
const action_t actionmaps[][UNIMAP_ROWS][UNIMAP_COLS] PROGMEM = { | |||
#endif | |||
UNIMAP( | |||
F13, F14, F15, F16, F17, F18, F19, F20, F21, F22, F23, F24, | |||
ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, PSCR,SLCK,PAUS, VOLD,VOLU,MUTE, | |||
GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, JYEN,BSPC, INS, HOME,PGUP, NLCK,PSLS,PAST,PMNS, | |||
TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, BSLS, DEL, END, PGDN, P7, P8, P9, PPLS, | |||
CAPS,A, S, D, F, G, H, J, K, L, SCLN,QUOT, NO, ENT, P4, P5, P6, PCMM, | |||
LSFT,NUBS,Z, X, C, V, B, N, M, COMM,DOT, SLSH, RO, RSFT, UP, P1, P2, P3, PEQL, | |||
LCTL,LGUI,LALT,MHEN, SPC, HENK,KANA,RALT,RGUI,FN0, RCTL, LEFT,DOWN,RGHT, P0, PDOT,PENT | |||
), | |||
UNIMAP( | |||
TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, | |||
GRV, TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, TRNS,TRNS,TRNS, TRNS,TRNS,TRNS, | |||
ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, TRNS,TRNS,TRNS, TRNS,TRNS,TRNS,TRNS, | |||
TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,PSCR,SLCK,PAUS,UP, INS, TRNS, TRNS,TRNS,TRNS, TRNS,TRNS,TRNS,TRNS, | |||
TRNS,VOLD,VOLU,MUTE,TRNS,TRNS,TRNS,TRNS,HOME,PGUP,LEFT,RGHT, TRNS,TRNS, TRNS,TRNS,TRNS,TRNS, | |||
TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,END, PGDN,DOWN, TRNS,TRNS, PGUP, TRNS,TRNS,TRNS,TRNS, | |||
TRNS,TRNS,TRNS,TRNS, TRNS, TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, HOME,PGDN,END, TRNS, TRNS,TRNS | |||
), | |||
}; |
@@ -0,0 +1,100 @@ | |||
/* | |||
Copyright 2016 Jun Wako <[email protected]> | |||
This program is free software: you can redistribute it and/or modify | |||
it under the terms of the GNU General Public License as published by | |||
the Free Software Foundation, either version 2 of the License, or | |||
(at your option) any later version. | |||
This program is distributed in the hope that it will be useful, | |||
but WITHOUT ANY WARRANTY; without even the implied warranty of | |||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |||
GNU General Public License for more details. | |||
You should have received a copy of the GNU General Public License | |||
along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
*/ | |||
#ifndef UNIMAP_TRNAS_H | |||
#define UNIMAP_TRNAS_H | |||
#include <stdint.h> | |||
#include <avr/pgmspace.h> | |||
#include "unimap.h" | |||
/* Mapping to Universal keyboard layout | |||
* | |||
* Universal keyboard layout | |||
* ,-----------------------------------------------. | |||
* |F13|F14|F15|F16|F17|F18|F19|F20|F21|F22|F23|F24| | |||
* ,---. |-----------------------------------------------| ,-----------. ,-----------. | |||
* |Esc| |F1 |F2 |F3 |F4 |F5 |F6 |F7 |F8 |F9 |F10|F11|F12| |PrS|ScL|Pau| |VDn|VUp|Mut| | |||
* `---' `-----------------------------------------------' `-----------' `-----------' | |||
* ,-----------------------------------------------------------. ,-----------. ,---------------. | |||
* | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|JPY|Bsp| |Ins|Hom|PgU| |NmL| /| *| -| | |||
* |-----------------------------------------------------------| |-----------| |---------------| | |||
* |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \ | |Del|End|PgD| | 7| 8| 9| +| | |||
* |-----------------------------------------------------------| `-----------' |---------------| | |||
* |CapsL | A| S| D| F| G| H| J| K| L| ;| '| #|Retn| | 4| 5| 6|KP,| | |||
* |-----------------------------------------------------------| ,---. |---------------| | |||
* |Shft| <| Z| X| C| V| B| N| M| ,| .| /| RO|Shift | |Up | | 1| 2| 3|KP=| | |||
* |-----------------------------------------------------------| ,-----------. |---------------| | |||
* |Ctl|Gui|Alt|MHEN| Space |HENK|KANA|Alt|Gui|App|Ctl| |Lef|Dow|Rig| | 0 | .|Ent| | |||
* `-----------------------------------------------------------' `-----------' `---------------' | |||
* | |||
* PS/2 scan codes | |||
* http://download.microsoft.com/download/1/6/1/161ba512-40e2-4cc9-843a-923143f3456c/translate.pdf | |||
* ,-----------------------------------------------. | |||
* | 08| 10| 18| 20| 28| 30| 38| 40| 48| 50| 57| 5F| | |||
* ,---. |-----------------------------------------------| ,-----------. ,-----------. | |||
* | 76| | 05| 06| 04| 0C| 03| 0B| 83| 0A| 01| 09| 78| 07| | FC| 7E| FE| | A1| B2| A3| | |||
* `---' `-----------------------------------------------' `-----------' `-----------' | |||
* ,-----------------------------------------------------------. ,-----------. ,---------------. | |||
* | 0E| 16| 1E| 26| 25| 2E| 36| 3D| 3E| 46| 45| 4E| 55| 6A| 66| | F0| EC| FD| | 77| CA| 7C| 7B| | |||
* |-----------------------------------------------------------| |-----------| |---------------| | |||
* | 0D | 15| 1D| 24| 2D| 2C| 35| 3C| 43| 44| 4D| 54| 5B| 5D | | F1| E9| FA| | 6C| 75| 7D| 79| | |||
* |-----------------------------------------------------------| `-----------' |---------------| | |||
* | 58 | 1C| 1B| 23| 2B| 34| 33| 3B| 42| 4B| 4C| 52| --| 5A | | 6B| 73| 74| 6D| | |||
* |-----------------------------------------------------------| ,---. |---------------| | |||
* | 12 | 61| 1A| 22| 21| 2A| 32| 31| 3A| 41| 49| 4A| 51| 59 | | F5| | 69| 72| 7A| 0F| | |||
* |-----------------------------------------------------------| ,-----------. |---------------| | |||
* | 14| 9F| 11| 67 | 29 | 64 | 13 | 91| A7| AF| 94| | EB| F2| F4| | 70 | 71| DA| | |||
* `-----------------------------------------------------------' `-----------' `---------------' | |||
*/ | |||
const uint8_t PROGMEM unimap_trans[MATRIX_ROWS][MATRIX_COLS] = { | |||
{ UNIMAP_NO, UNIMAP_F9, UNIMAP_NO, UNIMAP_F5, UNIMAP_F3, UNIMAP_F1, UNIMAP_F2, UNIMAP_F12 }, /* 00-07 */ | |||
{ UNIMAP_F13, UNIMAP_F10, UNIMAP_F8, UNIMAP_F6, UNIMAP_F4, UNIMAP_TAB, UNIMAP_GRV, UNIMAP_PEQL }, /* 08-0F */ | |||
{ UNIMAP_F14, UNIMAP_LALT, UNIMAP_LSHIFT,UNIMAP_KANA, UNIMAP_LCTL, UNIMAP_Q, UNIMAP_1, UNIMAP_NO }, /* 10-17 */ | |||
{ UNIMAP_F15, UNIMAP_NO, UNIMAP_Z, UNIMAP_S, UNIMAP_A, UNIMAP_W, UNIMAP_2, UNIMAP_NO }, /* 18-1F */ | |||
{ UNIMAP_F16, UNIMAP_C, UNIMAP_X, UNIMAP_D, UNIMAP_E, UNIMAP_4, UNIMAP_3, UNIMAP_NO }, /* 20-27 */ | |||
{ UNIMAP_F17, UNIMAP_SPACE, UNIMAP_V, UNIMAP_F, UNIMAP_T, UNIMAP_R, UNIMAP_5, UNIMAP_NO }, /* 28-2F */ | |||
{ UNIMAP_F18, UNIMAP_N, UNIMAP_B, UNIMAP_H, UNIMAP_G, UNIMAP_Y, UNIMAP_6, UNIMAP_NO }, /* 30-37 */ | |||
{ UNIMAP_F19, UNIMAP_NO, UNIMAP_M, UNIMAP_J, UNIMAP_U, UNIMAP_7, UNIMAP_8, UNIMAP_NO }, /* 38-3F */ | |||
{ UNIMAP_F20, UNIMAP_COMMA, UNIMAP_K, UNIMAP_I, UNIMAP_O, UNIMAP_0, UNIMAP_9, UNIMAP_NO }, /* 40-47 */ | |||
{ UNIMAP_F21, UNIMAP_DOT, UNIMAP_SLASH, UNIMAP_L, UNIMAP_SCOLON,UNIMAP_P, UNIMAP_MINUS, UNIMAP_NO }, /* 48-4F */ | |||
{ UNIMAP_F22, UNIMAP_RO, UNIMAP_QUOTE, UNIMAP_NO, UNIMAP_LBRC, UNIMAP_EQUAL, UNIMAP_NO, UNIMAP_F23 }, /* 50-57 */ | |||
{ UNIMAP_CAPS, UNIMAP_RSHIFT,UNIMAP_ENTER, UNIMAP_RBRC, UNIMAP_NO, UNIMAP_BSLASH,UNIMAP_NO, UNIMAP_F24 }, /* 58-5F */ | |||
{ UNIMAP_NO, UNIMAP_NUBS, UNIMAP_NO, UNIMAP_NO, UNIMAP_HENK, UNIMAP_NO, UNIMAP_BSPACE,UNIMAP_MHEN }, /* 60-67 */ | |||
{ UNIMAP_NO, UNIMAP_P1, UNIMAP_JYEN, UNIMAP_P4, UNIMAP_P7, UNIMAP_PCMM, UNIMAP_NO, UNIMAP_NO }, /* 68-6F */ | |||
{ UNIMAP_P0, UNIMAP_PDOT, UNIMAP_P2, UNIMAP_P5, UNIMAP_P6, UNIMAP_P8, UNIMAP_ESC, UNIMAP_NLCK }, /* 70-77 */ | |||
{ UNIMAP_F11, UNIMAP_PPLS, UNIMAP_P3, UNIMAP_PMNS, UNIMAP_PAST, UNIMAP_P9, UNIMAP_SLCK, UNIMAP_NO }, /* 78-7F */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_F7, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* 80-87 */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* 88-8F */ | |||
{ UNIMAP_NO, UNIMAP_RALT, UNIMAP_NO, UNIMAP_NO, UNIMAP_RCTRL, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* 90-97 */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_LGUI }, /* 98-9F */ | |||
{ UNIMAP_NO, UNIMAP_VOLD, UNIMAP_NO, UNIMAP_MUTE, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_RGUI }, /* A0-A7 */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_APP }, /* A8-AF */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_VOLU, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* B0-B7 */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* B8-BF */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* C0-C7 */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_PSLS, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* C8-CF */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* D0-D7 */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_PENT, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* D8-DF */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* E0-E7 */ | |||
{ UNIMAP_NO, UNIMAP_END, UNIMAP_NO, UNIMAP_LEFT, UNIMAP_HOME, UNIMAP_NO, UNIMAP_NO, UNIMAP_NO }, /* E8-EF */ | |||
{ UNIMAP_INS, UNIMAP_DEL, UNIMAP_DOWN, UNIMAP_NO, UNIMAP_RIGHT, UNIMAP_UP, UNIMAP_NO, UNIMAP_NO }, /* F0-F7 */ | |||
{ UNIMAP_NO, UNIMAP_NO, UNIMAP_PGDOWN,UNIMAP_NO, UNIMAP_PSCR, UNIMAP_PGUP, UNIMAP_PAUSE, UNIMAP_NO }, /* F8-FF */ | |||
}; | |||
#endif | |||
@@ -1,59 +1,59 @@ | |||
PROTOCOL_DIR = protocol | |||
ifdef PS2_MOUSE_ENABLE | |||
ifeq (yes,$(strip $(PS2_MOUSE_ENABLE))) | |||
SRC += $(PROTOCOL_DIR)/ps2_mouse.c | |||
OPT_DEFS += -DPS2_MOUSE_ENABLE | |||
OPT_DEFS += -DMOUSE_ENABLE | |||
endif | |||
ifdef PS2_USE_BUSYWAIT | |||
ifeq (yes,$(strip $(PS2_USE_BUSYWAIT))) | |||
SRC += protocol/ps2_busywait.c | |||
SRC += protocol/ps2_io_avr.c | |||
OPT_DEFS += -DPS2_USE_BUSYWAIT | |||
endif | |||
ifdef PS2_USE_INT | |||
ifeq (yes,$(strip $(PS2_USE_INT))) | |||
SRC += protocol/ps2_interrupt.c | |||
SRC += protocol/ps2_io_avr.c | |||
OPT_DEFS += -DPS2_USE_INT | |||
endif | |||
ifdef PS2_USE_USART | |||
ifeq (yes,$(strip $(PS2_USE_USART))) | |||
SRC += protocol/ps2_usart.c | |||
SRC += protocol/ps2_io_avr.c | |||
OPT_DEFS += -DPS2_USE_USART | |||
endif | |||
ifdef XT_USE_INT | |||
ifeq (yes,$(strip $(XT_USE_INT))) | |||
SRC += protocol/xt_interrupt.c | |||
SRC += protocol/xt_io_avr.c | |||
OPT_DEFS += -DXT_USE_INT | |||
endif | |||
ifdef SERIAL_MOUSE_MICROSOFT_ENABLE | |||
ifeq (yes,$(strip $(SERIAL_MOUSE_MICROSOFT_ENABLE))) | |||
SRC += $(PROTOCOL_DIR)/serial_mouse_microsoft.c | |||
OPT_DEFS += -DSERIAL_MOUSE_ENABLE -DSERIAL_MOUSE_MICROSOFT \ | |||
-DMOUSE_ENABLE | |||
endif | |||
ifdef SERIAL_MOUSE_MOUSESYSTEMS_ENABLE | |||
ifeq (yes,$(strip $(SERIAL_MOUSE_MOUSESYSTEMS_ENABLE))) | |||
SRC += $(PROTOCOL_DIR)/serial_mouse_mousesystems.c | |||
OPT_DEFS += -DSERIAL_MOUSE_ENABLE -DSERIAL_MOUSE_MOUSESYSTEMS \ | |||
-DMOUSE_ENABLE | |||
endif | |||
ifdef SERIAL_MOUSE_USE_SOFT | |||
ifeq (yes,$(strip $(SERIAL_MOUSE_USE_SOFT))) | |||
SRC += $(PROTOCOL_DIR)/serial_soft.c | |||
endif | |||
ifdef SERIAL_MOUSE_USE_UART | |||
ifeq (yes,$(strip $(SERIAL_MOUSE_USE_UART))) | |||
SRC += $(PROTOCOL_DIR)/serial_uart.c | |||
endif | |||
ifdef ADB_MOUSE_ENABLE | |||
ifeq (yes,$(strip $(ADB_MOUSE_ENABLE))) | |||
OPT_DEFS += -DADB_MOUSE_ENABLE -DMOUSE_ENABLE | |||
endif | |||