Improve documentation
This commit is contained in:
tmk
parent
16a583d7fd
commit
208f6d7f91
@ -1,151 +0,0 @@
|
|||||||
Alternative Controller for HHKB
|
|
||||||
===============================
|
|
||||||
|
|
||||||
Feature
|
|
||||||
-------
|
|
||||||
- Mouse Keys
|
|
||||||
- NKRO on USB(PJRC Tennsy only)
|
|
||||||
- Keymap Layers
|
|
||||||
|
|
||||||
|
|
||||||
Customize Keymap
|
|
||||||
----------------
|
|
||||||
see keymap.c.
|
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
Build
|
|
||||||
=====
|
|
||||||
PJRC Teensy
|
|
||||||
-----------
|
|
||||||
0. Edit matrix.c.
|
|
||||||
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
|
|
||||||
1. Define macros in config_pjrc.h.(Optional)
|
|
||||||
VENDOR_ID, PRODUCT_ID and string descriptor.
|
|
||||||
IS_COMMAND
|
|
||||||
2. Edit Makefile for MCU setting and build options.
|
|
||||||
MCU, F_CPU
|
|
||||||
MOUSEKEY_ENABLE, EXTRAKEY_ENABLE, NKRO_ENABLE
|
|
||||||
3. Build hex file.
|
|
||||||
$ make -f Makefile.pjrc
|
|
||||||
4. Program MCU.
|
|
||||||
$ make -f Makefile.pjrc program
|
|
||||||
|
|
||||||
|
|
||||||
V-USB
|
|
||||||
-----
|
|
||||||
0. Edit matrix.c and usbconfig.h.
|
|
||||||
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
|
|
||||||
define macros for V-USB in usbconfig.h.
|
|
||||||
1. Define macros in config_vusb.h.(Optional)
|
|
||||||
IS_COMMAND
|
|
||||||
2. Edit Makefile.vusb for MCU setting and build options.
|
|
||||||
MCU, F_CPU
|
|
||||||
MOUSEKEY_ENABLE, EXTRAKEY_ENABLE
|
|
||||||
3. Build hex file.
|
|
||||||
$ make -f Makefile.vusb
|
|
||||||
4. Program MCU.
|
|
||||||
$ make -f Makefile.vusb program
|
|
||||||
|
|
||||||
Using a bootloader to program for convenience is recommended.
|
|
||||||
Once program this V-USB bootloader at first, you can program MCU without
|
|
||||||
extra programmer. You should have reset switch to start up as bootloader
|
|
||||||
mode in this case.
|
|
||||||
USBaspLoader:
|
|
||||||
http://www.obdev.at/products/vusb/usbasploader.html
|
|
||||||
|
|
||||||
|
|
||||||
iWRAP
|
|
||||||
-----
|
|
||||||
0. Edit matrix.c and usbconfig.h.
|
|
||||||
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
|
|
||||||
define macros for V-USB in usbconfig.h.
|
|
||||||
1. Define macros in config_iwrap.h.(Optional)
|
|
||||||
IS_COMMAND
|
|
||||||
2. Edit Makefile.iwrap for MCU setting and build options.
|
|
||||||
MCU, F_CPU
|
|
||||||
MOUSEKEY_ENABLE, EXTRAKEY_ENABLE
|
|
||||||
3. Build hex file.
|
|
||||||
$ make -f Makefile.iwrap
|
|
||||||
4. Program MCU.
|
|
||||||
$ make -f Makefile.iwrap program
|
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
Hardware
|
|
||||||
========
|
|
||||||
PJRC Teensy
|
|
||||||
-----------
|
|
||||||
+---------------+
|
|
||||||
| Teensy++ |
|
|
||||||
| |
|
|
||||||
| | HHKB
|
|
||||||
| | ~~~~
|
|
||||||
| PB0-2|------->ROW(6-8)
|
|
||||||
| PB3-5|------->COL(9-11)
|
|
||||||
| PB6|------->ENABLE(12)
|
|
||||||
| PE6|<-------KEY(4)
|
|
||||||
| PE7|------->PREV(5)
|
|
||||||
| |
|
|
||||||
| |
|
|
||||||
| |
|
|
||||||
+---------------+
|
|
||||||
|
|
||||||
|
|
||||||
V-USB
|
|
||||||
-----
|
|
||||||
+---+ +---------------+
|
|
||||||
USB GND | | ATmega168 |
|
|
||||||
~~~ C3 | |
|
|
||||||
5V <-------+--------+---|Vcc,AVCC | HHKB
|
|
||||||
R1 | | ~~~~
|
|
||||||
D- <----+--+-----R2-----|INT1 PB2-4|------->ROW(6-8)
|
|
||||||
D+ <----|---+----R3-----|INT0 PC0-2|------->COL(9-11)
|
|
||||||
Z1 Z2 | PC3|------->ENABLE(12)
|
|
||||||
GND<----+---+-----------|GND PB0|<-------KEY(4)
|
|
||||||
| PB1|------->PREV(5)
|
|
||||||
| |
|
|
||||||
GND+-C2--+--|XTAL1 RXD|------->Debug Console
|
|
||||||
X1 | TXD|<-------Debug Console
|
|
||||||
GND+-C3--+--|XTAL2 RST|---SW--+GND
|
|
||||||
+---------------+
|
|
||||||
R1: 1.5K Ohm
|
|
||||||
R2,R3: 68 Ohm
|
|
||||||
Z1,Z2: Zener 3.6V
|
|
||||||
C1,C2: 22pF
|
|
||||||
C3: 0.1uF
|
|
||||||
X1: Crystal 20MHz(16MHz/12MHz)
|
|
||||||
SW: Push Switch(Optional for bootloader)
|
|
||||||
|
|
||||||
|
|
||||||
iWRAP
|
|
||||||
-----
|
|
||||||
+---------------+ WT12
|
|
||||||
5V | ATmega168 | 5V/3.3V~~~~
|
|
||||||
+-----+---|Vcc,AVCC PC4|---/--->iWRAP(RxD)
|
|
||||||
USB | C3 | PC5|<--/----iWRAP(TxD)
|
|
||||||
~~~ | + | |
|
|
||||||
5V <--BATT + GND | | HHKB
|
|
||||||
R1 | | ~~~~
|
|
||||||
D- <----+-----+--R2-----|INT1 PB2-4|------->ROW(6-8)
|
|
||||||
D+ <----|---+----R3-----|INT0 PC0-2|------->COL(9-11)
|
|
||||||
Z1 Z2 | PC3|------->ENABLE(12)
|
|
||||||
GND<----+---+-----------|GND PB0|<-------KEY(4)
|
|
||||||
| PB1|------->PREV(5)
|
|
||||||
| |
|
|
||||||
GND+-C2--+--|XTAL1 RXD|------->Debug Console
|
|
||||||
X1 | TXD|<-------Debug Console
|
|
||||||
GND+-C3--+--|XTAL2 RST|---SW--+GND
|
|
||||||
+---------------+
|
|
||||||
|
|
||||||
R1: 1.5K Ohm
|
|
||||||
R2,R3: 68 Ohm
|
|
||||||
Z1,Z2: Zener 3.6V
|
|
||||||
C1,C2: 22pF
|
|
||||||
C3: 0.1uF
|
|
||||||
X1: Crystal 12MHz
|
|
||||||
SW: Push Switch(Optional)
|
|
||||||
BATT: Li-Po Battery, Battery Charger and Voltage Regulator(5V and 3.3V).
|
|
||||||
|
|
||||||
|
|
||||||
EOF
|
|
||||||
135
keyboard/hhkb/README.md
Normal file
135
keyboard/hhkb/README.md
Normal file
@ -0,0 +1,135 @@
|
|||||||
|
Alternative Controller for HHKB Pro
|
||||||
|
===================================
|
||||||
|
I wanted to add some features like vi cursor and mouse keys to my [HHKB][HHKB] but its controller is not programmable and
|
||||||
|
firmware source code is not open, of course. This means customizing this keyboard needs to replace original
|
||||||
|
controller with programmable one. For this purpose I used PJRC [Teensy++][Teensy] as alternative controller.
|
||||||
|
|
||||||
|
[HHKB]: http://www.pfu.fujitsu.com/hhkeyboard/
|
||||||
|
[Teensy]: http://www.pjrc.com/teensy/
|
||||||
|
|
||||||
|
|
||||||
|
My keyboard firmware source tree is here: http://github.com/tmk/tmk_keyboard
|
||||||
|
See directory keyboard/hhkb to build firmware for HHKB.
|
||||||
|
|
||||||
|
|
||||||
|
##Features
|
||||||
|
* Customizable keymap
|
||||||
|
* More keymap layers(more Fn keys)
|
||||||
|
* Mouse keys
|
||||||
|
* USB NKRO
|
||||||
|
|
||||||
|
###Pros
|
||||||
|
* Without PCB trace cutting, case mod or any destructives
|
||||||
|
* Can keep original controller intact
|
||||||
|
* Can change all HHKB behaviour as you like
|
||||||
|
|
||||||
|
###Cons
|
||||||
|
* Void your warranty
|
||||||
|
* Lose USB hub function in case of Pro2
|
||||||
|
|
||||||
|
##DISCLAIMER
|
||||||
|
I'm not a professional of electronics or MCU programming. This may damage your HHKB.
|
||||||
|
And my English writing is poor, I'm not sure I can convey my notions accurately.
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
##Build Firmware
|
||||||
|
You can choose some combination of MCU and USB protocol stack.
|
||||||
|
|
||||||
|
### Teensy++(AVR USB family) with [LUFA]
|
||||||
|
0. Edit **matrix.c** to use your pin configuration. See doc/HHKB.txt for detail.
|
||||||
|
|
||||||
|
1. Edit **keymap.c** to use your favoirte keymap.
|
||||||
|
|
||||||
|
2. Edit **Makefile** if you want to use other `MCU` than Teensy++ 2.0.
|
||||||
|
|
||||||
|
3. Build firmware binary file:
|
||||||
|
`$ make -f Makefile.lufa`
|
||||||
|
|
||||||
|
4. Program MCU with PJRC [Teensy Loader] tool. If you install command line version of the loader just run:
|
||||||
|
`$ make -f Makefile.lufa teensy`
|
||||||
|
|
||||||
|
[LUFA]: http://www.fourwalledcubicle.com/LUFA.php
|
||||||
|
[Teensy Loader]: http://www.pjrc.com/teensy/loader.html
|
||||||
|
|
||||||
|
|
||||||
|
###AVR Mega with [V-USB]
|
||||||
|
Follow below if you want to use AVR with V-USB as .
|
||||||
|
|
||||||
|
0. Edit **matrix.c** to use your pin configuration. See doc/HHKB.txt for detail.
|
||||||
|
|
||||||
|
1. Edit **keymap.c** to use your favoirte keymap.
|
||||||
|
|
||||||
|
2. Edit **usbconfig.h** to configure V-USB options.
|
||||||
|
|
||||||
|
3. Edit **Makefile.vusb** to define `MCU` and `F_CPU`.
|
||||||
|
|
||||||
|
4. Build firmware binary file:
|
||||||
|
`$ make -f Makefile.vusb`
|
||||||
|
|
||||||
|
5. Program MCU with AVR programmer like AVRISPmkII. If you already have [USBaspLoader] on MCU just run:
|
||||||
|
`$ make -f Makefile.vusb program`
|
||||||
|
|
||||||
|
[V-USB]: http://www.obdev.at/products/vusb/index.html
|
||||||
|
[USBaspLoader]: http://www.obdev.at/products/vusb/usbasploader.html
|
||||||
|
|
||||||
|
|
||||||
|
###How to Customize Keymap
|
||||||
|
Later...
|
||||||
|
See **keymap.c**.
|
||||||
|
|
||||||
|
|
||||||
|
##Hardware
|
||||||
|
|
||||||
|
###Teensy++ installation
|
||||||
|
Angled USB mini B adapter is used to install Teensy++ laterally.
|
||||||
|
![doc/HHKB_img/teensy_install.jpg]
|
||||||
|
|
||||||
|
Bread baord wires are used to connect Teensy++.
|
||||||
|
![doc/HHKB_img/teensy_wiring.jpg]
|
||||||
|
![doc/HHKB_img/connector_contact.jpg]
|
||||||
|
|
||||||
|
|
||||||
|
###PJRC Teensy++ 2.0 connection
|
||||||
|
+---------------+
|
||||||
|
| Teensy++ |
|
||||||
|
| |
|
||||||
|
| | HHKB
|
||||||
|
| | ~~~~
|
||||||
|
| PB0-2|------->ROW(6-8)
|
||||||
|
| PB3-5|------->COL(9-11)
|
||||||
|
| PB6|------->ENABLE(12)
|
||||||
|
| PE6|<-------KEY(4)
|
||||||
|
| PE7|------->PREV(5)
|
||||||
|
| |
|
||||||
|
| |
|
||||||
|
| |
|
||||||
|
+---------------+
|
||||||
|
|
||||||
|
|
||||||
|
###V-USB circuit
|
||||||
|
+---+ +---------------+
|
||||||
|
USB GND | | ATmega168 |
|
||||||
|
~~~ C3 | |
|
||||||
|
5V <-------+--------+---|Vcc,AVCC | HHKB
|
||||||
|
R1 | | ~~~~
|
||||||
|
D- <----+--+-----R2-----|INT1 PB2-4|------->ROW(6-8)
|
||||||
|
D+ <----|---+----R3-----|INT0 PC0-2|------->COL(9-11)
|
||||||
|
Z1 Z2 | PC3|------->ENABLE(12)
|
||||||
|
GND<----+---+-----------|GND PB0|<-------KEY(4)
|
||||||
|
| PB1|------->PREV(5)
|
||||||
|
| |
|
||||||
|
GND+-C2--+--|XTAL1 RXD|------->Debug Console
|
||||||
|
X1 | TXD|<-------Debug Console
|
||||||
|
GND+-C3--+--|XTAL2 RST|---SW--+GND
|
||||||
|
+---------------+
|
||||||
|
R1: 1.5K Ohm
|
||||||
|
R2,R3: 68 Ohm
|
||||||
|
Z1,Z2: Zener 3.6V
|
||||||
|
C1,C2: 22pF
|
||||||
|
C3: 0.1uF
|
||||||
|
X1: Crystal 20MHz(16MHz/12MHz)
|
||||||
|
SW: Push Switch(Optional for bootloader)
|
||||||
@ -1,67 +1,16 @@
|
|||||||
Alternative Controller for HHKB pro
|
Internal of HHKB pro
|
||||||
===================================
|
=====================
|
||||||
I want to add vi cursor and mouse keys to HHKB. Original HHKB controller is not programmable and
|
HHKB pro has MCU and some chips on separate two PCBs.
|
||||||
firmware source code is not open. So, customizing HHKB needs to replace original controller with programmable one.
|
|
||||||
I used Teensy++ as alternative controller. Though a Teensy has enough ports to drive HHKB,
|
|
||||||
Teensy++ has clean pinout and it makes programing and wiring easier.
|
|
||||||
|
|
||||||
This is just a proof of concept for replacing controller of HHKB, not a complete firmware.
|
Controller PCB
|
||||||
|
--------------
|
||||||
My prototype firmware source tree is here:
|
|
||||||
github(http://github.com/tmk/tmk_keyboard)
|
|
||||||
This firmware is a port of my previous project:
|
|
||||||
HHKB style Mod(http://geekhack.org/showwiki.php?title=Island:11930)
|
|
||||||
PJRC:
|
|
||||||
Teensy++/Teensy(http://www.pjrc.com/teensy/)
|
|
||||||
|
|
||||||
|
|
||||||
Pros:
|
|
||||||
* without pattern cutting, case mod and soldering
|
|
||||||
* can keep original controller intact
|
|
||||||
* can change HHKB behaviour as you like(by C programming)
|
|
||||||
|
|
||||||
Cons:
|
|
||||||
* void your warranty
|
|
||||||
* unavailability of Teensy++/Teensy(because of PS3 cracking boom?)
|
|
||||||
|
|
||||||
Features:
|
|
||||||
* customized keymap
|
|
||||||
* more keymap layers
|
|
||||||
* mouse keys for minimum mouse operation(never comfortable for normal use)
|
|
||||||
* and more...(in the future)
|
|
||||||
|
|
||||||
Any suggestions or ideas are welcome.
|
|
||||||
|
|
||||||
|
|
||||||
NOTE:
|
|
||||||
My HHKB is just "Professional". This means followings may not be applied to "Professional2".
|
|
||||||
|
|
||||||
DISCLAIMER:
|
|
||||||
I'm not a professional for electronics and MCU programming. This may damage your HHKB.
|
|
||||||
And my English writing is poor, I'm not sure I can convey my notions accurately.
|
|
||||||
|
|
||||||
|
|
||||||
Teensy++ installation
|
|
||||||
---------------------
|
|
||||||
Angled USB mini B adapter is used to install Teensy++ laterally.
|
|
||||||
(teensy_install.jpg)
|
|
||||||
|
|
||||||
Bread baord wires are used to connect Teensy++.
|
|
||||||
(teensy_wiring.jpg)
|
|
||||||
(connector_contact.jpg)
|
|
||||||
|
|
||||||
|
|
||||||
HHKB internal
|
|
||||||
-------------
|
|
||||||
HHKB pro has some chips on separate two PCBs.
|
|
||||||
|
|
||||||
Controller PCB:
|
|
||||||
M38K07M4 Renesas MCU with USB function
|
M38K07M4 Renesas MCU with USB function
|
||||||
http://documentation.renesas.com/eng/products/mpumcu/rej03b0192_38k0ds.pdf
|
http://documentation.renesas.com/eng/products/mpumcu/rej03b0192_38k0ds.pdf
|
||||||
|
|
||||||
(HHKB_controller.jpg)
|
(HHKB_controller.jpg)
|
||||||
|
|
||||||
Keyswitch PCB:
|
Keyswitch PCB
|
||||||
|
-------------
|
||||||
HC4051 Analog Multiplexer: select a row line.
|
HC4051 Analog Multiplexer: select a row line.
|
||||||
http://www.alldatasheet.com/datasheet-pdf/pdf/203989/KODENSHI/KK74HC4051A.html
|
http://www.alldatasheet.com/datasheet-pdf/pdf/203989/KODENSHI/KK74HC4051A.html
|
||||||
LS145 BCD Decoder: select a column line.
|
LS145 BCD Decoder: select a column line.
|
||||||
@ -76,13 +25,16 @@ Keyswitch PCB:
|
|||||||
(HHKB_TP1684.jpg)
|
(HHKB_TP1684.jpg)
|
||||||
|
|
||||||
|
|
||||||
Two PCBs are connected by 15 lines. Vcc and GND use 3 lines each, other 9 lines are for keyboard signaling.
|
Connector Cable
|
||||||
|
---------------
|
||||||
|
Two PCBs are connected by 15 lines(13 in case of Pro2).
|
||||||
|
Vcc and GND use 3(2) lines each, other 9 lines are for keyboard signaling.
|
||||||
|
|
||||||
Keyswitch PCB connector Teensy++ pins
|
Keyswitch PCB connector Teensy++ pins
|
||||||
-------------------------------------------------------------------------------
|
-------------------------------------------------------------------------------
|
||||||
1 Vcc(5V) 5V
|
1 Vcc(5V) Not exist on Pro2 5V
|
||||||
2 Vcc(5V)
|
2 Vcc(5V) 5V
|
||||||
3 Vcc(5V)
|
3 Vcc(5V) 5V
|
||||||
4 TP1684 KEY: Low(0) when key pressed PE6 input(with pullup)
|
4 TP1684 KEY: Low(0) when key pressed PE6 input(with pullup)
|
||||||
5 TP1684 KEY_PREV: assert previous key state??? PE7 output
|
5 TP1684 KEY_PREV: assert previous key state??? PE7 output
|
||||||
6 HC4051 A(bit0) select 8 rows(0 to 7) PB0 output
|
6 HC4051 A(bit0) select 8 rows(0 to 7) PB0 output
|
||||||
@ -92,9 +44,11 @@ Two PCBs are connected by 15 lines. Vcc and GND use 3 lines each, other 9 lines
|
|||||||
10 LS145 B(bit1) PB4 output
|
10 LS145 B(bit1) PB4 output
|
||||||
11 LS145 C(bit2) PB5 output
|
11 LS145 C(bit2) PB5 output
|
||||||
12 LS145 D(enable) Low(0) enable selected column PB6 output
|
12 LS145 D(enable) Low(0) enable selected column PB6 output
|
||||||
13 GND
|
13 GND GND
|
||||||
14 GND
|
14 GND GND
|
||||||
15 GND GND
|
15 GND Not exist on Pro2 GND
|
||||||
|
|
||||||
|
NOTE: guessing pin5(KEY_PREV) may work for hysteresis of capacitive sensing.
|
||||||
|
|
||||||
(HHKB_connector.jpg)
|
(HHKB_connector.jpg)
|
||||||
|
|
||||||
@ -103,19 +57,20 @@ Keyswitch matrix
|
|||||||
----------------
|
----------------
|
||||||
60 keyswitches in 8*8 matrix. It is ghost-free and bounce-free.
|
60 keyswitches in 8*8 matrix. It is ghost-free and bounce-free.
|
||||||
|
|
||||||
COL 0 1 2 3 4 5 6 7
|
COL 0 1 2 3 4 5 6 7
|
||||||
ROW ---------------------------------------------------------------
|
ROW ---------------------------------------------------------------
|
||||||
0| 2 q w s a z x c
|
0| 2 q w s a z x c
|
||||||
1| 3 4 r e d f v b
|
1| 3 4 r e d f v b
|
||||||
2| 5 6 y t g h n _NONE_
|
2| 5 6 y t g h n _NONE_
|
||||||
3| 1 Esc Tab Control LShift LAlt LMeta Space
|
3| 1 Esc Tab Control LShift LAlt LMeta Space
|
||||||
4| 7 8 u i k j m _NONE_
|
4| 7 8 u i k j m _NONE_
|
||||||
5| \ ` Delete Return Fn RShift RAlt RMeta
|
5| \ ` Delete Return Fn RShift RAlt RMeta
|
||||||
6| 9 0 o p ; l , _NONE_
|
6| 9 0 o p ; l , _NONE_
|
||||||
7| - + ] [ ' / . _NONE_
|
7| - + ] [ ' / . _NONE_
|
||||||
|
|
||||||
|
|
||||||
Matrix diagram:
|
Matrix diagram:
|
||||||
|
|
||||||
+-------------------------+-+-+-+-+-+-+-+ Vcc
|
+-------------------------+-+-+-+-+-+-+-+ Vcc
|
||||||
|bias control? - - - - - - - - ---
|
|bias control? - - - - - - - - ---
|
||||||
| 3.9K*8 R R R R R R R R |
|
| 3.9K*8 R R R R R R R R |
|
||||||
@ -141,7 +96,8 @@ Matrix diagram:
|
|||||||
to controller
|
to controller
|
||||||
|
|
||||||
|
|
||||||
Signals charts:
|
Signals charts
|
||||||
|
--------------
|
||||||
While pressing space bar, watched HHKB original controller signals by logic analyzer.
|
While pressing space bar, watched HHKB original controller signals by logic analyzer.
|
||||||
Row and column is looping between 0-7 each for selecting a key.
|
Row and column is looping between 0-7 each for selecting a key.
|
||||||
A key is scaned every about 15ms, so scan rate is 66Hz.
|
A key is scaned every about 15ms, so scan rate is 66Hz.
|
||||||
@ -157,7 +113,8 @@ Signals charts:
|
|||||||
(HHKB_chart2.jpg)
|
(HHKB_chart2.jpg)
|
||||||
|
|
||||||
|
|
||||||
Matrix scan pseudo code:
|
Matrix scan pseudo code
|
||||||
|
-----------------------
|
||||||
for (row: 0-7) {
|
for (row: 0-7) {
|
||||||
SELECT_ROW(row); // set HC4051(A,B,C)
|
SELECT_ROW(row); // set HC4051(A,B,C)
|
||||||
|
|
||||||
@ -190,10 +147,5 @@ Matrix scan pseudo code:
|
|||||||
}
|
}
|
||||||
|
|
||||||
|
|
||||||
Keymap layers
|
|
||||||
-------------
|
|
||||||
Followings are added layers with additional Fn keys.
|
|
||||||
|
|
||||||
see keymap.c
|
|
||||||
|
|
||||||
EOF
|
EOF
|
||||||
|
|||||||
32
keyboard/hhkb/iwrap.txt
Normal file
32
keyboard/hhkb/iwrap.txt
Normal file
@ -0,0 +1,32 @@
|
|||||||
|
|
||||||
|
iWRAP
|
||||||
|
-----
|
||||||
|
+---------------+ WT12
|
||||||
|
5V | ATmega168 | 5V/3.3V~~~~
|
||||||
|
+-----+---|Vcc,AVCC PC4|---/--->iWRAP(RxD)
|
||||||
|
USB | C3 | PC5|<--/----iWRAP(TxD)
|
||||||
|
~~~ | + | |
|
||||||
|
5V <--BATT + GND | | HHKB
|
||||||
|
R1 | | ~~~~
|
||||||
|
D- <----+-----+--R2-----|INT1 PB2-4|------->ROW(6-8)
|
||||||
|
D+ <----|---+----R3-----|INT0 PC0-2|------->COL(9-11)
|
||||||
|
Z1 Z2 | PC3|------->ENABLE(12)
|
||||||
|
GND<----+---+-----------|GND PB0|<-------KEY(4)
|
||||||
|
| PB1|------->PREV(5)
|
||||||
|
| |
|
||||||
|
GND+-C2--+--|XTAL1 RXD|------->Debug Console
|
||||||
|
X1 | TXD|<-------Debug Console
|
||||||
|
GND+-C3--+--|XTAL2 RST|---SW--+GND
|
||||||
|
+---------------+
|
||||||
|
|
||||||
|
R1: 1.5K Ohm
|
||||||
|
R2,R3: 68 Ohm
|
||||||
|
Z1,Z2: Zener 3.6V
|
||||||
|
C1,C2: 22pF
|
||||||
|
C3: 0.1uF
|
||||||
|
X1: Crystal 12MHz
|
||||||
|
SW: Push Switch(Optional)
|
||||||
|
BATT: Li-Po Battery, Battery Charger and Voltage Regulator(5V and 3.3V).
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
Loading…
Reference in New Issue
Block a user