11 vuotta sitten · 4701b08b71
--- a/keyboard/gh60/Makefile.lufa
+++ b/keyboard/gh60/Makefile.lufa
@@ -0,0 +1,123 @@
 #----------------------------------------------------------------------------
 # On command line:
 #
 # make all = Make software.
 #
 # make clean = Clean out built project files.
 #
 # make coff = Convert ELF to AVR COFF.
 #
 # make extcoff = Convert ELF to AVR Extended COFF.
 #
 # make program = Download the hex file to the device.
 # Please customize your programmer settings(PROGRAM_CMD)
 #
 # make teensy = Download the hex file to the device, using teensy_loader_cli.
 # (must have teensy_loader_cli installed).
 #
 # make dfu = Download the hex file to the device, using dfu-programmer (must
 # have dfu-programmer installed).
 #
 # make flip = Download the hex file to the device, using Atmel FLIP (must
 # have Atmel FLIP installed).
 #
 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
 # (must have dfu-programmer installed).
 #
 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
 # (must have Atmel FLIP installed).
 #
 # make debug = Start either simulavr or avarice as specified for debugging, 
 # with avr-gdb or avr-insight as the front end for debugging.
 #
 # make filename.s = Just compile filename.c into the assembler code only.
 #
 # make filename.i = Create a preprocessed source file for use in submitting
 # bug reports to the GCC project.
 #
 # To rebuild project do "make clean" then "make all".
 #----------------------------------------------------------------------------

 # Target file name (without extension).
 TARGET = gh60_lufa

 # Directory common source filess exist
 TOP_DIR = ../..

 # Directory keyboard dependent files exist
 TARGET_DIR = .


 # List C source files here. (C dependencies are automatically generated.)
 SRC += keymap.c \
 matrix.c \
 led.c

 CONFIG_H = config.h


 # MCU name
 #MCU = at90usb1287
 MCU = atmega32u4

 # Processor frequency.
 # This will define a symbol, F_CPU, in all source code files equal to the
 # processor frequency in Hz. You can then use this symbol in your source code to
 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
 # automatically to create a 32-bit value in your source code.
 #
 # This will be an integer division of F_USB below, as it is sourced by
 # F_USB after it has run through any CPU prescalers. Note that this value
 # does not *change* the processor frequency - it should merely be updated to
 # reflect the processor speed set externally so that the code can use accurate
 # software delays.
 F_CPU = 16000000


 #
 # LUFA specific
 #
 # Target architecture (see library "Board Types" documentation).
 ARCH = AVR8

 # Input clock frequency.
 # This will define a symbol, F_USB, in all source code files equal to the
 # input clock frequency (before any prescaling is performed) in Hz. This value may
 # differ from F_CPU if prescaling is used on the latter, and is required as the
 # raw input clock is fed directly to the PLL sections of the AVR for high speed
 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
 # at the end, this will be done automatically to create a 32-bit value in your
 # source code.
 #
 # If no clock division is performed on the input clock inside the AVR (via the
 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)


 # Build Options
 # comment out to disable the options.
 #
 MOUSEKEY_ENABLE = yes # Mouse keys
 EXTRAKEY_ENABLE = yes # Audio control and System control
 CONSOLE_ENABLE = yes # Console for debug
 #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
 #PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support


 # Boot Section Size in bytes
 # Teensy halfKay 512
 # Atmel DFU loader 4096
 # LUFA bootloader 4096
 OPT_DEFS += -DBOOT_SIZE=4096


 # Search Path
 VPATH += $(TARGET_DIR)
 VPATH += $(TOP_DIR)

 include $(TOP_DIR)/protocol/lufa.mk
 include $(TOP_DIR)/common.mk
 include $(TOP_DIR)/rules.mk

 plain: OPT_DEFS += -DPLAIN_MAP
 plain: all
--- a/keyboard/gh60/Makefile.pjrc
+++ b/keyboard/gh60/Makefile.pjrc
@@ -0,0 +1,93 @@
 #----------------------------------------------------------------------------
 # On command line:
 #
 # make all = Make software.
 #
 # make clean = Clean out built project files.
 #
 # make coff = Convert ELF to AVR COFF.
 #
 # make extcoff = Convert ELF to AVR Extended COFF.
 #
 # make program = Download the hex file to the device.
 # Please customize your programmer settings(PROGRAM_CMD)
 #
 # make teensy = Download the hex file to the device, using teensy_loader_cli.
 # (must have teensy_loader_cli installed).
 #
 # make dfu = Download the hex file to the device, using dfu-programmer (must
 # have dfu-programmer installed).
 #
 # make flip = Download the hex file to the device, using Atmel FLIP (must
 # have Atmel FLIP installed).
 #
 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
 # (must have dfu-programmer installed).
 #
 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
 # (must have Atmel FLIP installed).
 #
 # make debug = Start either simulavr or avarice as specified for debugging, 
 # with avr-gdb or avr-insight as the front end for debugging.
 #
 # make filename.s = Just compile filename.c into the assembler code only.
 #
 # make filename.i = Create a preprocessed source file for use in submitting
 # bug reports to the GCC project.
 #
 # To rebuild project do "make clean" then "make all".
 #----------------------------------------------------------------------------

 # Target file name (without extension).
 TARGET = gh60_pjrc

 # Directory common source filess exist
 TOP_DIR = ../..

 # Directory keyboard dependent files exist
 TARGET_DIR = .

 # keyboard dependent files
 SRC = keymap.c \
 matrix.c \
 led.c

 CONFIG_H = config.h


 # MCU name, you MUST set this to match the board you are using
 # type "make clean" after changing this, so all files will be rebuilt
 #MCU = at90usb162 # Teensy 1.0
 MCU = atmega32u4 # Teensy 2.0
 #MCU = at90usb646 # Teensy++ 1.0
 #MCU = at90usb1286 # Teensy++ 2.0


 # Processor frequency.
 # Normally the first thing your program should do is set the clock prescaler,
 # so your program will run at the correct speed. You should also set this
 # variable to same clock speed. The _delay_ms() macro uses this, and many
 # examples use this variable to calculate timings. Do not add a "UL" here.
 F_CPU = 16000000


 # Build Options
 # comment out to disable the options.
 #
 MOUSEKEY_ENABLE = yes # Mouse keys
 #PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support
 EXTRAKEY_ENABLE = yes # Audio control and System control
 NKRO_ENABLE = yes # USB Nkey Rollover
 CONSOLE_ENABLE = yes # Console for debug


 # Search Path
 VPATH += $(TARGET_DIR)
 VPATH += $(TOP_DIR)

 include $(TOP_DIR)/protocol/pjrc.mk
 include $(TOP_DIR)/common.mk
 include $(TOP_DIR)/rules.mk

 plain: OPT_DEFS += -DPLAIN_MAP
 plain: all
--- a/keyboard/gh60/README.md
+++ b/keyboard/gh60/README.md
@@ -0,0 +1,89 @@
 GH60 keyboard firmware
 ======================
 DIY compact keyboard designed and run by komar007 and Geekhack community.

 ## Threads on Geekhack.org
 - [Prototyping](http://geekhack.org/index.php?topic=34959.0)
 - [Beta-test](http://geekhack.org/index.php?topic=37570.0)


 ## Build
 Move to this directory then just run `make` like:

 $ make -f Makfile.pjrc


 ## Keymap
 See keymap.c to define your own favourite keymap.

 ###Keymap with funky layers.
 Layer 0: Default Layer
 ,-----------------------------------------------------------.
 |Esc| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backsp |
 |-----------------------------------------------------------|
 |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \|
 |-----------------------------------------------------------|
 |Caps | A| S| D| F| G| H| J| K| L|Fn3| '|Return |
 |-----------------------------------------------------------|
 |Shift | Z| X| C| V| B| N| M| ,| .|Fn2|Shift |
 |-----------------------------------------------------------|
 |Ctrl|Gui |Alt | Space |Alt |Gui |App |Fn1 |
 `-----------------------------------------------------------'

 Layer 1: HHKB mode
 ,-----------------------------------------------------------.
 |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delete |
 |-----------------------------------------------------------|
 |Caps | | | | | | | |Psc|Slk|Pus|Up | |Inser|
 |-----------------------------------------------------------|
 |Contro|VoD|VoU|Mut| | | *| /|Hom|PgU|Lef|Rig|Enter |
 |-----------------------------------------------------------|
 |Shift | | | | | | +| -|End|PgD|Dow|Shift |
 |-----------------------------------------------------------|
 |Ctrl|Gui |Alt | Space |Alt |Gui |App |xxx |
 `-----------------------------------------------------------'

 Layer 2: Vi mode
 ,-----------------------------------------------------------.
 | `| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Backsp |
 |-----------------------------------------------------------|
 |Tab |Hom|PgD|Up |PgU|End|Hom|PgD|PgU|End| | | | |
 |-----------------------------------------------------------|
 |Contro| |Lef|Dow|Rig| |Lef|Dow|Up |Rig| | |Return |
 |-----------------------------------------------------------|
 |Shift | | | | | |Hom|PgD|PgU|End|xxx|Shift |
 |-----------------------------------------------------------|
 |Ctrl|Gui |Alt | Space |Alt |Gui |App |Ctrl|
 `-----------------------------------------------------------'

 Layer 3: Mouse mode
 ,-----------------------------------------------------------.
 | `| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Backsp |
 |-----------------------------------------------------------|
 |Tab |MwL|MwD|McU|MwU|MwR|MwL|MwD|MwU|MwR| | | | |
 |-----------------------------------------------------------|
 |Contro| |McL|McD|McR| |McL|McD|McU|McR|xxx| |Return |
 |-----------------------------------------------------------|
 |Shift | | |Mb1|Mb2|Mb3|Mb2|Mb1| | | |Shift |
 |-----------------------------------------------------------|
 |Ctrl|Gui |Alt | Space |Alt |Gui |xxx |Ctrl|
 `-----------------------------------------------------------'
 Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel 

 ### Plain keymap without Fn layer.
 This will be useful if you want to use key mapping tool like AHK.
 To get this plain keymap run:

 $ make -f Makefile.pjrc plain

 ,-----------------------------------------------------------.
 |Esc| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backsp |
 |-----------------------------------------------------------|
 |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \|
 |-----------------------------------------------------------|
 |Caps | A| S| D| F| G| H| J| K| L| ;| '|Return |
 |-----------------------------------------------------------|
 |Shift | Z| X| C| V| B| N| M| ,| .| /|Shift |
 |-----------------------------------------------------------|
 |Ctrl|Gui |Alt | Space |Alt |Gui |App |Ctrl|
 `-----------------------------------------------------------'
--- a/keyboard/gh60/config.h
+++ b/keyboard/gh60/config.h
@@ -0,0 +1,50 @@
 /*
 Copyright 2012 Jun Wako <[email protected]>

 This program is free software: you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
 the Free Software Foundation, either version 2 of the License, or
 (at your option) any later version.

 This program is distributed in the hope that it will be useful,
 but WITHOUT ANY WARRANTY; without even the implied warranty of
 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
 GNU General Public License for more details.

 You should have received a copy of the GNU General Public License
 along with this program. If not, see <http://www.gnu.org/licenses/>.
 */

 #ifndef CONFIG_H
 #define CONFIG_H


 /* USB Device descriptor parameter */
 #define VENDOR_ID 0xFEED
 #define PRODUCT_ID 0x6060
 #define DEVICE_VER 0x0001
 #define MANUFACTURER geekhack
 #define PRODUCT GH60


 /* message strings */
 #define DESCRIPTION t.m.k. keyboard firmware for GH60


 /* matrix size */
 #define MATRIX_ROWS 5
 #define MATRIX_COLS 14

 /* define if matrix has ghost */
 //#define MATRIX_HAS_GHOST

 /* Set 0 if need no debouncing */
 #define DEBOUNCE 5


 /* key combination for command */
 #define IS_COMMAND() ( \
 keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
 )

 #endif
--- a/keyboard/gh60/keymap.c
+++ b/keyboard/gh60/keymap.c
@@ -0,0 +1,202 @@
 /*
 Copyright 2012 Jun Wako <[email protected]>

 This program is free software: you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
 the Free Software Foundation, either version 2 of the License, or
 (at your option) any later version.

 This program is distributed in the hope that it will be useful,
 but WITHOUT ANY WARRANTY; without even the implied warranty of
 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
 GNU General Public License for more details.

 You should have received a copy of the GNU General Public License
 along with this program. If not, see <http://www.gnu.org/licenses/>.
 */
 #include <stdint.h>
 #include <stdbool.h>
 #include <avr/pgmspace.h>
 #include "keycode.h"
 #include "print.h"
 #include "debug.h"
 #include "util.h"
 #include "keymap.h"


 /* GH60 keymap definition macro 
 * K2C, K31 and K3C are extra keys for ISO
 */
 #define KEYMAP( \
 K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
 K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
 K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \
 K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
 K40, K41, K42, K45, K4A, K4B, K4C, K4D \
 ) { \
 { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D }, \
 { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D }, \
 { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D }, \
 { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37, KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D }, \
 { KC_##K40, KC_##K41, KC_##K42, KC_NO, KC_NO, KC_##K45, KC_NO, KC_NO, KC_NO, KC_NO, KC_##K4A, KC_##K4B, KC_##K4C, KC_##K4D } \
 }

 /* ANSI valiant. No extra keys for ISO */
 #define KEYMAP_ANSI( \
 K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
 K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
 K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2D, \
 K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3D, \
 K40, K41, K42, K45, K4A, K4B, K4C, K4D \
 ) KEYMAP( \ 
 K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
 K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
 K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO, K2D, \
 K30, NO, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, NO, K3D, \
 K40, K41, K42, K45, K4A, K4B, K4C, K4D \
 )

 #define KEYCODE(layer, row, col) (pgm_read_byte(&keymaps[(layer)][(row)][(col)]))


 // Assign Fn key(0-7) to a layer to which switch with the Fn key pressed.
 static const uint8_t PROGMEM fn_layer[] = {
 0, // Fn0
 1, // Fn1
 2, // Fn2
 3, // Fn3
 3, // Fn4
 0, // Fn5
 0, // Fn6
 0 // Fn7
 };

 // Assign Fn key(0-7) to a keycode sent when release Fn key without use of the layer.
 // See layer.c for details.
 static const uint8_t PROGMEM fn_keycode[] = {
 KC_NO, // Fn0
 KC_NO, // Fn1
 KC_SLSH, // Fn2
 KC_SCLN, // Fn3
 KC_NO, // Fn4
 KC_NO, // Fn5
 KC_NO, // Fn6
 KC_NO // Fn7
 };

 static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
 #ifdef PLAIN_MAP
 /* Layer 0: Default Layer
 * ,-----------------------------------------------------------.
 * |Esc| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backsp |
 * |-----------------------------------------------------------|
 * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \|
 * |-----------------------------------------------------------|
 * |Caps | A| S| D| F| G| H| J| K| L| ;| '|Return |
 * |-----------------------------------------------------------|
 * |Shift | Z| X| C| V| B| N| M| ,| .| /|Shift |
 * |-----------------------------------------------------------|
 * |Ctrl|Gui |Alt | Space |Alt |Gui |App |Ctrl|
 * `-----------------------------------------------------------'
 */
 KEYMAP(ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, \
 TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSLS, \
 CAPS,A, S, D, F, G, H, J, K, L, SCLN,QUOT,NO, ENT, \
 LSFT,NO, Z, X, C, V, B, N, M, COMM,DOT, SLSH,NO, RSFT, \
 LCTL,LGUI,LALT, SPC, RALT,RGUI,APP, RCTL),
 #else
 /* Layer 0: Default Layer
 * ,-----------------------------------------------------------.
 * |Esc| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backsp |
 * |-----------------------------------------------------------|
 * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \|
 * |-----------------------------------------------------------|
 * |Caps | A| S| D| F| G| H| J| K| L|Fn3| '|Return |
 * |-----------------------------------------------------------|
 * |Shift | Z| X| C| V| B| N| M| ,| .|Fn2|Shift |
 * |-----------------------------------------------------------|
 * |Ctrl|Gui |Alt | Space |Alt |Fn4 |Fn4 |Fn1 |
 * `-----------------------------------------------------------'
 */
 KEYMAP_ANSI(
 ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, \
 TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSLS, \
 LCTL,A, S, D, F, G, H, J, K, L, FN3, QUOT, ENT, \
 LSFT,Z, X, C, V, B, N, M, COMM,DOT, FN2, RSFT, \
 LCTL,LGUI,LALT, SPC, RALT,FN4, FN4, FN1),
 /* Layer 1: HHKB mode
 * ,-----------------------------------------------------------.
 * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delete |
 * |-----------------------------------------------------------|
 * |Caps | | | | | | | |Psc|Slk|Pus|Up | |Inser|
 * |-----------------------------------------------------------|
 * |Contro|VoD|VoU|Mut| | | *| /|Hom|PgU|Lef|Rig|Enter |
 * |-----------------------------------------------------------|
 * |Shift | | | | | | +| -|End|PgD|Dow|Shift |
 * |-----------------------------------------------------------|
 * |Ctrl|Gui |Alt | Space |Alt |Gui |App |xxx |
 * `-----------------------------------------------------------'
 */ 
 KEYMAP_ANSI(
 PWR, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, \
 CAPS,NO, NO, NO, NO, NO, NO, NO, PSCR,SLCK,PAUS,UP, NO, INS, \
 LCTL,VOLD,VOLU,MUTE,NO, NO, PAST,PSLS,HOME,PGUP,LEFT,RGHT, ENT, \
 LSFT,NO, NO, NO, NO, NO, PPLS,PMNS,END, PGDN,DOWN, RSFT, \
 LCTL,LGUI,LALT, SPC, RALT,RGUI,APP, FN1),
 /* Layer 2: Vi mode (Slash)
 * ,-----------------------------------------------------------.
 * | `| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Backsp |
 * |-----------------------------------------------------------|
 * |Tab |Hom|PgD|Up |PgU|End|Hom|PgD|PgU|End| | | | |
 * |-----------------------------------------------------------|
 * |Contro| |Lef|Dow|Rig| |Lef|Dow|Up |Rig| | |Return |
 * |-----------------------------------------------------------|
 * |Shift | | | | | |Hom|PgD|PgU|End|xxx|Shift |
 * |-----------------------------------------------------------|
 * |Ctrl|Gui |Alt | Space |Alt |Gui |App |Ctrl|
 * `-----------------------------------------------------------'
 */
 KEYMAP_ANSI(
 GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, BSPC, \
 TAB, HOME,PGDN,UP, PGUP,END, HOME,PGDN,PGUP,END, NO, NO, NO, NO, \
 LCTL,NO, LEFT,DOWN,RGHT,NO, LEFT,DOWN,UP, RGHT,NO, NO, ENT, \
 LSFT,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, FN2, RSFT, \
 LCTL,LGUI,LALT, SPC, RALT,RGUI,APP, RCTL),
 /* Layer 3: Mouse mode (Semicolon/App)
 * ,-----------------------------------------------------------.
 * | `| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Backsp |
 * |-----------------------------------------------------------|
 * |Tab | | | | | |MwL|MwD|MwU|MwR| | | | |
 * |-----------------------------------------------------------|
 * |Contro| |Ac0|Ac1|Ac1| |McL|McD|McU|McR|xxx| |Return |
 * |-----------------------------------------------------------|
 * |Shift | | | | |Mb3|Mb2|Mb1|Mb4|Mb5| |Shift |
 * |-----------------------------------------------------------|
 * |Ctrl|Gui |Alt | Space | |xxx |xxx | |
 * `-----------------------------------------------------------'
 * Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel 
 */
 KEYMAP_ANSI(
 GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, BSPC, \
 TAB, NO, NO, NO, NO, NO, WH_L,WH_D,WH_U,WH_R,NO, NO, NO, NO, \
 LCTL,NO, ACL0,ACL1,ACL2,NO, MS_L,MS_D,MS_U,MS_R,FN3, NO, ENT, \
 LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,BTN4,BTN5,NO, RSFT, \
 LCTL,LGUI,LALT, BTN1, NO, FN4, FN4, NO ),
 #endif
 };


 uint8_t keymap_get_keycode(uint8_t layer, uint8_t row, uint8_t col)
 {
 return KEYCODE(layer, row, col);
 }

 uint8_t keymap_fn_layer(uint8_t index)
 {
 return pgm_read_byte(&fn_layer[index]);
 }

 uint8_t keymap_fn_keycode(uint8_t index)
 {
 return pgm_read_byte(&fn_keycode[index]);
 }
--- a/keyboard/gh60/led.c
+++ b/keyboard/gh60/led.c
@@ -0,0 +1,34 @@
 /*
 Copyright 2012 Jun Wako <[email protected]>

 This program is free software: you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
 the Free Software Foundation, either version 2 of the License, or
 (at your option) any later version.

 This program is distributed in the hope that it will be useful,
 but WITHOUT ANY WARRANTY; without even the implied warranty of
 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
 GNU General Public License for more details.

 You should have received a copy of the GNU General Public License
 along with this program. If not, see <http://www.gnu.org/licenses/>.
 */

 #include <avr/io.h>
 #include "stdint.h"
 #include "led.h"


 void led_set(uint8_t usb_led)
 {
 if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
 // output low
 DDRB |= (1<<2);
 PORTB &= ~(1<<2);
 } else {
 // Hi-Z
 DDRB &= ~(1<<2);
 PORTB &= ~(1<<2);
 }
 }
--- a/keyboard/gh60/matrix.c
+++ b/keyboard/gh60/matrix.c
@@ -0,0 +1,224 @@
 /*
 Copyright 2012 Jun Wako <[email protected]>

 This program is free software: you can redistribute it and/or modify
 it under the terms of the GNU General Public License as published by
 the Free Software Foundation, either version 2 of the License, or
 (at your option) any later version.

 This program is distributed in the hope that it will be useful,
 but WITHOUT ANY WARRANTY; without even the implied warranty of
 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
 GNU General Public License for more details.

 You should have received a copy of the GNU General Public License
 along with this program. If not, see <http://www.gnu.org/licenses/>.
 */

 /*
 * scan matrix
 */
 #include <stdint.h>
 #include <stdbool.h>
 #include <avr/io.h>
 #include <util/delay.h>
 #include "print.h"
 #include "debug.h"
 #include "util.h"
 #include "matrix.h"


 #ifndef DEBOUNCE
 # define DEBOUNCE 5
 #endif
 static uint8_t debouncing = DEBOUNCE;

 /* matrix state(1:on, 0:off) */
 static uint16_t *matrix;
 static uint16_t *matrix_debouncing;
 static uint16_t matrix0[MATRIX_ROWS];
 static uint16_t matrix1[MATRIX_ROWS];
 static bool is_modified;

 static uint16_t read_cols(void);
 static void init_cols(void);
 static void unselect_rows(void);
 static void select_row(uint8_t row);


 inline
 uint8_t matrix_rows(void)
 {
 return MATRIX_ROWS;
 }

 inline
 uint8_t matrix_cols(void)
 {
 return MATRIX_COLS;
 }

 void matrix_init(void)
 {
 // initialize row and col
 unselect_rows();
 init_cols();

 // initialize matrix state: all keys off
 matrix = matrix0;
 matrix_debouncing = matrix1;
 for (uint8_t i=0; i < MATRIX_ROWS; i++) {
 matrix[i] = 0;
 matrix_debouncing[i] = 0;
 }
 is_modified = false;
 }

 uint8_t matrix_scan(void)
 {
 for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
 //unselect_rows();
 select_row(i);
 _delay_us(30); // without this wait read unstable value.
 uint16_t cols = read_cols();
 if (matrix_debouncing[i] != cols) {
 matrix_debouncing[i] = cols;
 if (debouncing) {
 debug("bounce!: "); debug_hex(debouncing); debug("\n");
 }
 debouncing = DEBOUNCE;
 is_modified = false;
 }
 unselect_rows();
 }
 //unselect_rows();

 if (debouncing) {
 debouncing--;
 _delay_ms(1);
 } else {
 uint16_t *tmp = matrix;
 matrix = matrix_debouncing;
 matrix_debouncing = tmp;
 is_modified = true;
 }

 return 1;
 }

 bool matrix_is_modified(void)
 {
 return is_modified;
 }

 inline
 bool matrix_has_ghost(void)
 {
 return false;
 }

 inline
 bool matrix_is_on(uint8_t row, uint8_t col)
 {
 return (matrix[row] & (1<<col));
 }

 inline
 uint16_t matrix_get_row(uint8_t row)
 {
 return matrix[row];
 }

 void matrix_print(void)
 {
 print("\nr/c 01234567890ABCDEF\n");
 for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
 phex(row); print(": ");
 pbin_reverse16(matrix_get_row(row));
 print("\n");
 }
 }

 uint8_t matrix_key_count(void)
 {
 uint8_t count = 0;
 for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
 count += bitpop16(matrix[i]);
 }
 return count;
 }

 /* Column pin configuration
 * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13
 * pin: F0 F1 E6 C7 C6 B6 D4 B1 B0 B5 B4 D7 D6 B3
 */
 static void init_cols(void)
 {
 // Input with pull-up(DDR:0, PORT:1)
 DDRF &= ~(1<<0 | 1<<1);
 PORTF |= (1<<0 | 1<<1);
 DDRE &= ~(1<<6);
 PORTE |= (1<<6);
 DDRD &= ~(1<<7 | 1<<6 | 1<<4);
 PORTD |= (1<<7 | 1<<6 | 1<<4);
 DDRC &= ~(1<<7 | 1<<6);
 PORTC |= (1<<7 | 1<<6);
 DDRB &= ~(1<<6 | 1<< 5 | 1<<4 | 1<<3 | 1<<1 | 1<<0);
 PORTB |= (1<<6 | 1<< 5 | 1<<4 | 1<<3 | 1<<1 | 1<<0);
 }

 static uint16_t read_cols(void)
 {
 return (PINF&(1<<0) ? 0 : (1<<0)) |
 (PINF&(1<<1) ? 0 : (1<<1)) |
 (PINE&(1<<6) ? 0 : (1<<2)) |
 (PINC&(1<<7) ? 0 : (1<<3)) |
 (PINC&(1<<6) ? 0 : (1<<4)) |
 (PINB&(1<<6) ? 0 : (1<<5)) |
 (PIND&(1<<4) ? 0 : (1<<6)) |
 (PINB&(1<<1) ? 0 : (1<<7)) |
 (PINB&(1<<0) ? 0 : (1<<8)) |
 (PINB&(1<<5) ? 0 : (1<<9)) |
 (PINB&(1<<4) ? 0 : (1<<10)) |
 (PIND&(1<<7) ? 0 : (1<<11)) |
 (PIND&(1<<6) ? 0 : (1<<12)) |
 (PINB&(1<<3) ? 0 : (1<<13));
 }

 /* Row pin configuration
 * row: 0 1 2 3 4
 * pin: D0 D1 D2 D3 D5
 */
 static void unselect_rows(void)
 {
 // Hi-Z(DDR:0, PORT:0) to unselect
 DDRD &= ~0b00101111;
 PORTD &= ~0b00101111;
 }

 static void select_row(uint8_t row)
 {
 // Output low(DDR:1, PORT:0) to select
 switch (row) {
 case 0:
 DDRD |= (1<<0);
 PORTD &= ~(1<<0);
 break;
 case 1:
 DDRD |= (1<<1);
 PORTD &= ~(1<<1);
 break;
 case 2:
 DDRD |= (1<<2);
 PORTD &= ~(1<<2);
 break;
 case 3:
 DDRD |= (1<<3);
 PORTD &= ~(1<<3);
 break;
 case 4:
 DDRD |= (1<<5);
 PORTD &= ~(1<<5);
 break;
 }
 }
--- a/protocol/pjrc/main.c
+++ b/protocol/pjrc/main.c
@@ -44,9 +44,6 @@

 int main(void)
 {
 DEBUG_LED_CONFIG;
 DEBUG_LED_OFF;

 // set for 16 MHz clock
 CPU_PRESCALE(0);