#include <avr/eeprom.h> | |||||
#include <avr/interrupt.h> | |||||
#include <util/delay.h> | |||||
#include "progmem.h" | |||||
#include "timer.h" | |||||
#include "rgblight.h" | |||||
#include "debug.h" | |||||
const uint8_t DIM_CURVE[] PROGMEM = { | |||||
0, 1, 1, 2, 2, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, | |||||
3, 3, 3, 3, 3, 3, 3, 4, 4, 4, 4, 4, 4, 4, 4, 4, | |||||
4, 4, 4, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 6, 6, 6, | |||||
6, 6, 6, 6, 6, 7, 7, 7, 7, 7, 7, 7, 8, 8, 8, 8, | |||||
8, 8, 9, 9, 9, 9, 9, 9, 10, 10, 10, 10, 10, 11, 11, 11, | |||||
11, 11, 12, 12, 12, 12, 12, 13, 13, 13, 13, 14, 14, 14, 14, 15, | |||||
15, 15, 16, 16, 16, 16, 17, 17, 17, 18, 18, 18, 19, 19, 19, 20, | |||||
20, 20, 21, 21, 22, 22, 22, 23, 23, 24, 24, 25, 25, 25, 26, 26, | |||||
27, 27, 28, 28, 29, 29, 30, 30, 31, 32, 32, 33, 33, 34, 35, 35, | |||||
36, 36, 37, 38, 38, 39, 40, 40, 41, 42, 43, 43, 44, 45, 46, 47, | |||||
48, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, | |||||
63, 64, 65, 66, 68, 69, 70, 71, 73, 74, 75, 76, 78, 79, 81, 82, | |||||
83, 85, 86, 88, 90, 91, 93, 94, 96, 98, 99, 101, 103, 105, 107, 109, | |||||
110, 112, 114, 116, 118, 121, 123, 125, 127, 129, 132, 134, 136, 139, 141, 144, | |||||
146, 149, 151, 154, 157, 159, 162, 165, 168, 171, 174, 177, 180, 183, 186, 190, | |||||
193, 196, 200, 203, 207, 211, 214, 218, 222, 226, 230, 234, 238, 242, 248, 255, | |||||
}; | |||||
const uint8_t RGBLED_BREATHING_TABLE[] PROGMEM = {0,0,0,0,1,1,1,2,2,3,4,5,5,6,7,9,10,11,12,14,15,17,18,20,21,23,25,27,29,31,33,35,37,40,42,44,47,49,52,54,57,59,62,65,67,70,73,76,79,82,85,88,90,93,97,100,103,106,109,112,115,118,121,124,127,131,134,137,140,143,146,149,152,155,158,162,165,167,170,173,176,179,182,185,188,190,193,196,198,201,203,206,208,211,213,215,218,220,222,224,226,228,230,232,234,235,237,238,240,241,243,244,245,246,248,249,250,250,251,252,253,253,254,254,254,255,255,255,255,255,255,255,254,254,254,253,253,252,251,250,250,249,248,246,245,244,243,241,240,238,237,235,234,232,230,228,226,224,222,220,218,215,213,211,208,206,203,201,198,196,193,190,188,185,182,179,176,173,170,167,165,162,158,155,152,149,146,143,140,137,134,131,128,124,121,118,115,112,109,106,103,100,97,93,90,88,85,82,79,76,73,70,67,65,62,59,57,54,52,49,47,44,42,40,37,35,33,31,29,27,25,23,21,20,18,17,15,14,12,11,10,9,7,6,5,5,4,3,2,2,1,1,1,0,0,0}; | |||||
const uint8_t RGBLED_BREATHING_INTERVALS[] PROGMEM = {30, 20, 10, 5}; | |||||
const uint8_t RGBLED_RAINBOW_MOOD_INTERVALS[] PROGMEM = {120, 60, 30}; | |||||
const uint8_t RGBLED_RAINBOW_SWIRL_INTERVALS[] PROGMEM = {100, 50, 20}; | |||||
const uint8_t RGBLED_SNAKE_INTERVALS[] PROGMEM = {100, 50, 20}; | |||||
const uint8_t RGBLED_KNIGHT_INTERVALS[] PROGMEM = {100, 50, 20}; | |||||
rgblight_config_t rgblight_config; | |||||
rgblight_config_t inmem_config; | |||||
struct cRGB led[RGBLED_NUM]; | |||||
uint8_t rgblight_inited = 0; | |||||
void sethsv(uint16_t hue, uint8_t sat, uint8_t val, struct cRGB *led1) { | |||||
/* convert hue, saturation and brightness ( HSB/HSV ) to RGB | |||||
The DIM_CURVE is used only on brightness/value and on saturation (inverted). | |||||
This looks the most natural. | |||||
*/ | |||||
uint8_t r, g, b; | |||||
val = pgm_read_byte(&DIM_CURVE[val]); | |||||
sat = 255 - pgm_read_byte(&DIM_CURVE[255 - sat]); | |||||
uint8_t base; | |||||
if (sat == 0) { // Acromatic color (gray). Hue doesn't mind. | |||||
r = val; | |||||
g = val; | |||||
b = val; | |||||
} else { | |||||
base = ((255 - sat) * val) >> 8; | |||||
switch (hue / 60) { | |||||
case 0: | |||||
r = val; | |||||
g = (((val - base)*hue) / 60) + base; | |||||
b = base; | |||||
break; | |||||
case 1: | |||||
r = (((val - base)*(60 - (hue % 60))) / 60) + base; | |||||
g = val; | |||||
b = base; | |||||
break; | |||||
case 2: | |||||
r = base; | |||||
g = val; | |||||
b = (((val - base)*(hue % 60)) / 60) + base; | |||||
break; | |||||
case 3: | |||||
r = base; | |||||
g = (((val - base)*(60 - (hue % 60))) / 60) + base; | |||||
b = val; | |||||
break; | |||||
case 4: | |||||
r = (((val - base)*(hue % 60)) / 60) + base; | |||||
g = base; | |||||
b = val; | |||||
break; | |||||
case 5: | |||||
r = val; | |||||
g = base; | |||||
b = (((val - base)*(60 - (hue % 60))) / 60) + base; | |||||
break; | |||||
} | |||||
} | |||||
setrgb(r,g,b, led1); | |||||
} | |||||
void setrgb(uint8_t r, uint8_t g, uint8_t b, struct cRGB *led1) { | |||||
(*led1).r = r; | |||||
(*led1).g = g; | |||||
(*led1).b = b; | |||||
} | |||||
uint32_t eeconfig_read_rgblight(void) { | |||||
return eeprom_read_dword(EECONFIG_RGBLIGHT); | |||||
} | |||||
void eeconfig_write_rgblight(uint32_t val) { | |||||
eeprom_write_dword(EECONFIG_RGBLIGHT, val); | |||||
} | |||||
void eeconfig_write_rgblight_default(void) { | |||||
dprintf("eeconfig_write_rgblight_default\n"); | |||||
rgblight_config.enable = 1; | |||||
rgblight_config.mode = 1; | |||||
rgblight_config.hue = 200; | |||||
rgblight_config.sat = 204; | |||||
rgblight_config.val = 204; | |||||
eeconfig_write_rgblight(rgblight_config.raw); | |||||
} | |||||
void eeconfig_debug_rgblight(void) { | |||||
dprintf("rgblight_config eprom\n"); | |||||
dprintf("rgblight_config.enable = %d\n", rgblight_config.enable); | |||||
dprintf("rghlight_config.mode = %d\n", rgblight_config.mode); | |||||
dprintf("rgblight_config.hue = %d\n", rgblight_config.hue); | |||||
dprintf("rgblight_config.sat = %d\n", rgblight_config.sat); | |||||
dprintf("rgblight_config.val = %d\n", rgblight_config.val); | |||||
} | |||||
void rgblight_init(void) { | |||||
debug_enable = 1; // Debug ON! | |||||
dprintf("rgblight_init called.\n"); | |||||
rgblight_inited = 1; | |||||
dprintf("rgblight_init start!\n"); | |||||
if (!eeconfig_is_enabled()) { | |||||
dprintf("rgblight_init eeconfig is not enabled.\n"); | |||||
eeconfig_init(); | |||||
eeconfig_write_rgblight_default(); | |||||
} | |||||
rgblight_config.raw = eeconfig_read_rgblight(); | |||||
if (!rgblight_config.mode) { | |||||
dprintf("rgblight_init rgblight_config.mode = 0. Write default values to EEPROM.\n"); | |||||
eeconfig_write_rgblight_default(); | |||||
rgblight_config.raw = eeconfig_read_rgblight(); | |||||
} | |||||
eeconfig_debug_rgblight(); // display current eeprom values | |||||
rgblight_timer_init(); // setup the timer | |||||
if (rgblight_config.enable) { | |||||
rgblight_mode(rgblight_config.mode); | |||||
} | |||||
} | |||||
void rgblight_increase(void) { | |||||
uint8_t mode; | |||||
if (rgblight_config.mode < RGBLIGHT_MODES) { | |||||
mode = rgblight_config.mode + 1; | |||||
} | |||||
rgblight_mode(mode); | |||||
} | |||||
void rgblight_decrease(void) { | |||||
uint8_t mode; | |||||
if (rgblight_config.mode > 1) { //mode will never < 1, if mode is less than 1, eeprom need to be initialized. | |||||
mode = rgblight_config.mode-1; | |||||
} | |||||
rgblight_mode(mode); | |||||
} | |||||
void rgblight_step(void) { | |||||
uint8_t mode; | |||||
mode = rgblight_config.mode + 1; | |||||
if (mode > RGBLIGHT_MODES) { | |||||
mode = 1; | |||||
} | |||||
rgblight_mode(mode); | |||||
} | |||||
void rgblight_mode(uint8_t mode) { | |||||
if (!rgblight_config.enable) { | |||||
return; | |||||
} | |||||
if (mode<1) { | |||||
rgblight_config.mode = 1; | |||||
} else if (mode > RGBLIGHT_MODES) { | |||||
rgblight_config.mode = RGBLIGHT_MODES; | |||||
} else { | |||||
rgblight_config.mode = mode; | |||||
} | |||||
eeconfig_write_rgblight(rgblight_config.raw); | |||||
dprintf("rgblight mode: %u\n", rgblight_config.mode); | |||||
if (rgblight_config.mode == 1) { | |||||
rgblight_timer_disable(); | |||||
} else if (rgblight_config.mode >=2 && rgblight_config.mode <=23) { | |||||
// MODE 2-5, breathing | |||||
// MODE 6-8, rainbow mood | |||||
// MODE 9-14, rainbow swirl | |||||
// MODE 15-20, snake | |||||
// MODE 21-23, knight | |||||
rgblight_timer_enable(); | |||||
} | |||||
rgblight_sethsv(rgblight_config.hue, rgblight_config.sat, rgblight_config.val); | |||||
} | |||||
void rgblight_toggle(void) { | |||||
rgblight_config.enable ^= 1; | |||||
eeconfig_write_rgblight(rgblight_config.raw); | |||||
dprintf("rgblight toggle: rgblight_config.enable = %u\n", rgblight_config.enable); | |||||
if (rgblight_config.enable) { | |||||
rgblight_mode(rgblight_config.mode); | |||||
} else { | |||||
rgblight_timer_disable(); | |||||
_delay_ms(50); | |||||
rgblight_set(); | |||||
} | |||||
} | |||||
void rgblight_increase_hue(void){ | |||||
uint16_t hue; | |||||
hue = (rgblight_config.hue+RGBLIGHT_HUE_STEP) % 360; | |||||
rgblight_sethsv(hue, rgblight_config.sat, rgblight_config.val); | |||||
} | |||||
void rgblight_decrease_hue(void){ | |||||
uint16_t hue; | |||||
if (rgblight_config.hue-RGBLIGHT_HUE_STEP <0 ) { | |||||
hue = (rgblight_config.hue+360-RGBLIGHT_HUE_STEP) % 360; | |||||
} else { | |||||
hue = (rgblight_config.hue-RGBLIGHT_HUE_STEP) % 360; | |||||
} | |||||
rgblight_sethsv(hue, rgblight_config.sat, rgblight_config.val); | |||||
} | |||||
void rgblight_increase_sat(void) { | |||||
uint8_t sat; | |||||
if (rgblight_config.sat + RGBLIGHT_SAT_STEP > 255) { | |||||
sat = 255; | |||||
} else { | |||||
sat = rgblight_config.sat+RGBLIGHT_SAT_STEP; | |||||
} | |||||
rgblight_sethsv(rgblight_config.hue, sat, rgblight_config.val); | |||||
} | |||||
void rgblight_decrease_sat(void){ | |||||
uint8_t sat; | |||||
if (rgblight_config.sat - RGBLIGHT_SAT_STEP < 0) { | |||||
sat = 0; | |||||
} else { | |||||
sat = rgblight_config.sat-RGBLIGHT_SAT_STEP; | |||||
} | |||||
rgblight_sethsv(rgblight_config.hue, sat, rgblight_config.val); | |||||
} | |||||
void rgblight_increase_val(void){ | |||||
uint8_t val; | |||||
if (rgblight_config.val + RGBLIGHT_VAL_STEP > 255) { | |||||
val = 255; | |||||
} else { | |||||
val = rgblight_config.val+RGBLIGHT_VAL_STEP; | |||||
} | |||||
rgblight_sethsv(rgblight_config.hue, rgblight_config.sat, val); | |||||
} | |||||
void rgblight_decrease_val(void) { | |||||
uint8_t val; | |||||
if (rgblight_config.val - RGBLIGHT_VAL_STEP < 0) { | |||||
val = 0; | |||||
} else { | |||||
val = rgblight_config.val-RGBLIGHT_VAL_STEP; | |||||
} | |||||
rgblight_sethsv(rgblight_config.hue, rgblight_config.sat, val); | |||||
} | |||||
void rgblight_sethsv_noeeprom(uint16_t hue, uint8_t sat, uint8_t val){ | |||||
inmem_config.raw = rgblight_config.raw; | |||||
if (rgblight_config.enable) { | |||||
struct cRGB tmp_led; | |||||
sethsv(hue, sat, val, &tmp_led); | |||||
inmem_config.hue = hue; | |||||
inmem_config.sat = sat; | |||||
inmem_config.val = val; | |||||
// dprintf("rgblight set hue [MEMORY]: %u,%u,%u\n", inmem_config.hue, inmem_config.sat, inmem_config.val); | |||||
rgblight_setrgb(tmp_led.r, tmp_led.g, tmp_led.b); | |||||
} | |||||
} | |||||
void rgblight_sethsv(uint16_t hue, uint8_t sat, uint8_t val){ | |||||
if (rgblight_config.enable) { | |||||
if (rgblight_config.mode == 1) { | |||||
// same static color | |||||
rgblight_sethsv_noeeprom(hue, sat, val); | |||||
} else { | |||||
// all LEDs in same color | |||||
if (rgblight_config.mode >= 2 && rgblight_config.mode <= 5) { | |||||
// breathing mode, ignore the change of val, use in memory value instead | |||||
val = rgblight_config.val; | |||||
} else if (rgblight_config.mode >= 6 && rgblight_config.mode <= 14) { | |||||
// rainbow mood and rainbow swirl, ignore the change of hue | |||||
hue = rgblight_config.hue; | |||||
} | |||||
} | |||||
rgblight_config.hue = hue; | |||||
rgblight_config.sat = sat; | |||||
rgblight_config.val = val; | |||||
eeconfig_write_rgblight(rgblight_config.raw); | |||||
dprintf("rgblight set hsv [EEPROM]: %u,%u,%u\n", rgblight_config.hue, rgblight_config.sat, rgblight_config.val); | |||||
} | |||||
} | |||||
void rgblight_setrgb(uint8_t r, uint8_t g, uint8_t b){ | |||||
// dprintf("rgblight set rgb: %u,%u,%u\n", r,g,b); | |||||
for (uint8_t i=0;i<RGBLED_NUM;i++) { | |||||
led[i].r = r; | |||||
led[i].g = g; | |||||
led[i].b = b; | |||||
} | |||||
rgblight_set(); | |||||
} | |||||
void rgblight_set(void) { | |||||
if (rgblight_config.enable) { | |||||
ws2812_setleds(led, RGBLED_NUM); | |||||
} else { | |||||
for (uint8_t i=0;i<RGBLED_NUM;i++) { | |||||
led[i].r = 0; | |||||
led[i].g = 0; | |||||
led[i].b = 0; | |||||
} | |||||
ws2812_setleds(led, RGBLED_NUM); | |||||
} | |||||
} | |||||
// Animation timer -- AVR Timer1 | |||||
void rgblight_timer_init(void) { | |||||
static uint8_t rgblight_timer_is_init = 0; | |||||
if (rgblight_timer_is_init) { | |||||
return; | |||||
} | |||||
rgblight_timer_is_init = 1; | |||||
/* Timer 1 setup */ | |||||
TCCR1B = _BV(WGM12) //CTC mode OCR1A as TOP | |||||
| _BV(CS12); //Clock selelct: clk/1 | |||||
/* Set TOP value */ | |||||
uint8_t sreg = SREG; | |||||
cli(); | |||||
OCR1AH = (RGBLED_TIMER_TOP>>8)&0xff; | |||||
OCR1AL = RGBLED_TIMER_TOP&0xff; | |||||
SREG = sreg; | |||||
} | |||||
void rgblight_timer_enable(void) { | |||||
TIMSK1 |= _BV(OCIE1A); | |||||
dprintf("TIMER1 enabled.\n"); | |||||
} | |||||
void rgblight_timer_disable(void) { | |||||
TIMSK1 &= ~_BV(OCIE1A); | |||||
dprintf("TIMER1 disabled.\n"); | |||||
} | |||||
void rgblight_timer_toggle(void) { | |||||
TIMSK1 ^= _BV(OCIE1A); | |||||
dprintf("TIMER1 toggled.\n"); | |||||
} | |||||
ISR(TIMER1_COMPA_vect) { | |||||
// Mode = 1, static light, do nothing here | |||||
if (rgblight_config.mode>=2 && rgblight_config.mode<=5) { | |||||
// mode = 2 to 5, breathing mode | |||||
rgblight_effect_breathing(rgblight_config.mode-2); | |||||
} else if (rgblight_config.mode>=6 && rgblight_config.mode<=8) { | |||||
rgblight_effect_rainbow_mood(rgblight_config.mode-6); | |||||
} else if (rgblight_config.mode>=9 && rgblight_config.mode<=14) { | |||||
rgblight_effect_rainbow_swirl(rgblight_config.mode-9); | |||||
} else if (rgblight_config.mode>=15 && rgblight_config.mode<=20) { | |||||
rgblight_effect_snake(rgblight_config.mode-15); | |||||
} else if (rgblight_config.mode>=21 && rgblight_config.mode<=23) { | |||||
rgblight_effect_knight(rgblight_config.mode-21); | |||||
} | |||||
} | |||||
// effects | |||||
void rgblight_effect_breathing(uint8_t interval) { | |||||
static uint8_t pos = 0; | |||||
static uint16_t last_timer = 0; | |||||
if (timer_elapsed(last_timer)<pgm_read_byte(&RGBLED_BREATHING_INTERVALS[interval])) return; | |||||
last_timer = timer_read(); | |||||
rgblight_sethsv_noeeprom(rgblight_config.hue, rgblight_config.sat, pgm_read_byte(&RGBLED_BREATHING_TABLE[pos])); | |||||
pos = (pos+1) % 256; | |||||
} | |||||
void rgblight_effect_rainbow_mood(uint8_t interval) { | |||||
static uint16_t current_hue=0; | |||||
static uint16_t last_timer = 0; | |||||
if (timer_elapsed(last_timer)<pgm_read_byte(&RGBLED_RAINBOW_MOOD_INTERVALS[interval])) return; | |||||
last_timer = timer_read(); | |||||
rgblight_sethsv_noeeprom(current_hue, rgblight_config.sat, rgblight_config.val); | |||||
current_hue = (current_hue+1) % 360; | |||||
} | |||||
void rgblight_effect_rainbow_swirl(uint8_t interval) { | |||||
static uint16_t current_hue=0; | |||||
static uint16_t last_timer = 0; | |||||
uint16_t hue; | |||||
uint8_t i; | |||||
if (timer_elapsed(last_timer)<pgm_read_byte(&RGBLED_RAINBOW_MOOD_INTERVALS[interval/2])) return; | |||||
last_timer = timer_read(); | |||||
for (i=0; i<RGBLED_NUM; i++) { | |||||
hue = (360/RGBLED_NUM*i+current_hue)%360; | |||||
sethsv(hue, rgblight_config.sat, rgblight_config.val, &led[i]); | |||||
} | |||||
rgblight_set(); | |||||
if (interval % 2) { | |||||
current_hue = (current_hue+1) % 360; | |||||
} else { | |||||
if (current_hue -1 < 0) { | |||||
current_hue = 359; | |||||
} else { | |||||
current_hue = current_hue - 1; | |||||
} | |||||
} | |||||
} | |||||
void rgblight_effect_snake(uint8_t interval) { | |||||
static uint8_t pos=0; | |||||
static uint16_t last_timer = 0; | |||||
uint8_t i,j; | |||||
int8_t k; | |||||
int8_t increament = 1; | |||||
if (interval%2) increament = -1; | |||||
if (timer_elapsed(last_timer)<pgm_read_byte(&RGBLED_SNAKE_INTERVALS[interval/2])) return; | |||||
last_timer = timer_read(); | |||||
for (i=0;i<RGBLED_NUM;i++) { | |||||
led[i].r=0; | |||||
led[i].g=0; | |||||
led[i].b=0; | |||||
for (j=0;j<RGBLIGHT_EFFECT_SNAKE_LENGTH;j++) { | |||||
k = pos+j*increament; | |||||
if (k<0) k = k+RGBLED_NUM; | |||||
if (i==k) { | |||||
sethsv(rgblight_config.hue, rgblight_config.sat, (uint8_t)(rgblight_config.val*(RGBLIGHT_EFFECT_SNAKE_LENGTH-j)/RGBLIGHT_EFFECT_SNAKE_LENGTH), &led[i]); | |||||
} | |||||
} | |||||
} | |||||
rgblight_set(); | |||||
if (increament == 1) { | |||||
if (pos - 1 < 0) { | |||||
pos = 13; | |||||
} else { | |||||
pos -= 1; | |||||
} | |||||
} else { | |||||
pos = (pos+1)%RGBLED_NUM; | |||||
} | |||||
} | |||||
void rgblight_effect_knight(uint8_t interval) { | |||||
static int8_t pos=0; | |||||
static uint16_t last_timer = 0; | |||||
uint8_t i,j,cur; | |||||
int8_t k; | |||||
struct cRGB preled[RGBLED_NUM]; | |||||
static int8_t increament = -1; | |||||
if (timer_elapsed(last_timer)<pgm_read_byte(&RGBLED_KNIGHT_INTERVALS[interval])) return; | |||||
last_timer = timer_read(); | |||||
for (i=0;i<RGBLED_NUM;i++) { | |||||
preled[i].r=0; | |||||
preled[i].g=0; | |||||
preled[i].b=0; | |||||
for (j=0;j<RGBLIGHT_EFFECT_KNIGHT_LENGTH;j++) { | |||||
k = pos+j*increament; | |||||
if (k<0) k = 0; | |||||
if (k>=RGBLED_NUM) k=RGBLED_NUM-1; | |||||
if (i==k) { | |||||
sethsv(rgblight_config.hue, rgblight_config.sat, rgblight_config.val, &preled[i]); | |||||
} | |||||
} | |||||
} | |||||
if (RGBLIGHT_EFFECT_KNIGHT_OFFSET) { | |||||
for (i=0;i<RGBLED_NUM;i++) { | |||||
cur = (i+RGBLIGHT_EFFECT_KNIGHT_OFFSET) % RGBLED_NUM; | |||||
led[i].r = preled[cur].r; | |||||
led[i].g = preled[cur].g; | |||||
led[i].b = preled[cur].b; | |||||
} | |||||
} | |||||
rgblight_set(); | |||||
if (increament == 1) { | |||||
if (pos - 1 < 0 - RGBLIGHT_EFFECT_KNIGHT_LENGTH) { | |||||
pos = 0- RGBLIGHT_EFFECT_KNIGHT_LENGTH; | |||||
increament = -1; | |||||
} else { | |||||
pos -= 1; | |||||
} | |||||
} else { | |||||
if (pos+1>RGBLED_NUM+RGBLIGHT_EFFECT_KNIGHT_LENGTH) { | |||||
pos = RGBLED_NUM+RGBLIGHT_EFFECT_KNIGHT_LENGTH-1; | |||||
increament = 1; | |||||
} else { | |||||
pos += 1; | |||||
} | |||||
} | |||||
} |
#ifndef RGBLIGHT_H | |||||
#define RGBLIGHT_H | |||||
#ifndef RGBLIGHT_MODES | |||||
#define RGBLIGHT_MODES 23 | |||||
#endif | |||||
#ifndef RGBLIGHT_EFFECT_SNAKE_LENGTH | |||||
#define RGBLIGHT_EFFECT_SNAKE_LENGTH 7 | |||||
#endif | |||||
#ifndef RGBLIGHT_EFFECT_KNIGHT_LENGTH | |||||
#define RGBLIGHT_EFFECT_KNIGHT_LENGTH 7 | |||||
#endif | |||||
#ifndef RGBLIGHT_EFFECT_KNIGHT_OFFSET | |||||
#define RGBLIGHT_EFFECT_KNIGHT_OFFSET 11 | |||||
#endif | |||||
#ifndef RGBLIGHT_EFFECT_DUALKNIGHT_LENGTH | |||||
#define RGBLIGHT_EFFECT_DUALKNIGHT_LENGTH 4 | |||||
#endif | |||||
#ifndef RGBLIGHT_HUE_STEP | |||||
#define RGBLIGHT_HUE_STEP 10 | |||||
#endif | |||||
#ifndef RGBLIGHT_SAT_STEP | |||||
#define RGBLIGHT_SAT_STEP 17 | |||||
#endif | |||||
#ifndef RGBLIGHT_VAL_STEP | |||||
#define RGBLIGHT_VAL_STEP 17 | |||||
#endif | |||||
#define RGBLED_TIMER_TOP F_CPU/(256*64) | |||||
#include <stdint.h> | |||||
#include <stdbool.h> | |||||
#include "eeconfig.h" | |||||
#include "light_ws2812.h" | |||||
typedef union { | |||||
uint32_t raw; | |||||
struct { | |||||
bool enable :1; | |||||
uint8_t mode :6; | |||||
uint16_t hue :9; | |||||
uint8_t sat :8; | |||||
uint8_t val :8; | |||||
}; | |||||
} rgblight_config_t; | |||||
void rgblight_init(void); | |||||
void rgblight_increase(void); | |||||
void rgblight_decrease(void); | |||||
void rgblight_toggle(void); | |||||
void rgblight_step(void); | |||||
void rgblight_mode(uint8_t mode); | |||||
void rgblight_set(void); | |||||
void rgblight_increase_hue(void); | |||||
void rgblight_decrease_hue(void); | |||||
void rgblight_increase_sat(void); | |||||
void rgblight_decrease_sat(void); | |||||
void rgblight_increase_val(void); | |||||
void rgblight_decrease_val(void); | |||||
void rgblight_sethsv(uint16_t hue, uint8_t sat, uint8_t val); | |||||
void rgblight_setrgb(uint8_t r, uint8_t g, uint8_t b); | |||||
#define EECONFIG_RGBLIGHT (uint8_t *)7 | |||||
uint32_t eeconfig_read_rgblight(void); | |||||
void eeconfig_write_rgblight(uint32_t val); | |||||
void eeconfig_write_rgblight_default(void); | |||||
void eeconfig_debug_rgblight(void); | |||||
void sethsv(uint16_t hue, uint8_t sat, uint8_t val, struct cRGB *led1); | |||||
void setrgb(uint8_t r, uint8_t g, uint8_t b, struct cRGB *led1); | |||||
void rgblight_sethsv_noeeprom(uint16_t hue, uint8_t sat, uint8_t val); | |||||
void rgblight_timer_init(void); | |||||
void rgblight_timer_enable(void); | |||||
void rgblight_timer_disable(void); | |||||
void rgblight_timer_toggle(void); | |||||
void rgblight_effect_breathing(uint8_t interval); | |||||
void rgblight_effect_rainbow_mood(uint8_t interval); | |||||
void rgblight_effect_rainbow_swirl(uint8_t interval); | |||||
void rgblight_effect_snake(uint8_t interval); | |||||
void rgblight_effect_knight(uint8_t interval); | |||||
#endif |
/* Name: usbconfig.h | |||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers | |||||
* Author: Christian Starkjohann | |||||
* Creation Date: 2005-04-01 | |||||
* Tabsize: 4 | |||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH | |||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt) | |||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $ | |||||
*/ | |||||
#ifndef __usbconfig_h_included__ | |||||
#define __usbconfig_h_included__ | |||||
/* | |||||
General Description: | |||||
This file is an example configuration (with inline documentation) for the USB | |||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is | |||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may | |||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any | |||||
other hardware interrupt, as long as it is the highest level interrupt, see | |||||
section at the end of this file). | |||||
*/ | |||||
/* ---------------------------- Hardware Config ---------------------------- */ | |||||
#define USB_CFG_IOPORTNAME D | |||||
/* This is the port where the USB bus is connected. When you configure it to | |||||
* "B", the registers PORTB, PINB and DDRB will be used. | |||||
*/ | |||||
#define USB_CFG_DMINUS_BIT 4 | |||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected. | |||||
* This may be any bit in the port. | |||||
*/ | |||||
#define USB_CFG_DPLUS_BIT 2 | |||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected. | |||||
* This may be any bit in the port. Please note that D+ must also be connected | |||||
* to interrupt pin INT0! [You can also use other interrupts, see section | |||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as | |||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the | |||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame | |||||
* markers every millisecond.] | |||||
*/ | |||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000) | |||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000, | |||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code | |||||
* require no crystal, they tolerate +/- 1% deviation from the nominal | |||||
* frequency. All other rates require a precision of 2000 ppm and thus a | |||||
* crystal! | |||||
* Since F_CPU should be defined to your actual clock rate anyway, you should | |||||
* not need to modify this setting. | |||||
*/ | |||||
#define USB_CFG_CHECK_CRC 0 | |||||
/* Define this to 1 if you want that the driver checks integrity of incoming | |||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are | |||||
* currently only available for 18 MHz crystal clock. You must choose | |||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option. | |||||
*/ | |||||
/* ----------------------- Optional Hardware Config ------------------------ */ | |||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */ | |||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of | |||||
* V+, you can connect and disconnect the device from firmware by calling | |||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h). | |||||
* This constant defines the port on which the pullup resistor is connected. | |||||
*/ | |||||
/* #define USB_CFG_PULLUP_BIT 4 */ | |||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined | |||||
* above) where the 1.5k pullup resistor is connected. See description | |||||
* above for details. | |||||
*/ | |||||
/* --------------------------- Functional Range ---------------------------- */ | |||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1 | |||||
/* Define this to 1 if you want to compile a version with two endpoints: The | |||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint | |||||
* number). | |||||
*/ | |||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1 | |||||
/* Define this to 1 if you want to compile a version with three endpoints: The | |||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number | |||||
* configured below) and a catch-all default interrupt-in endpoint as above. | |||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature. | |||||
*/ | |||||
#define USB_CFG_EP3_NUMBER 3 | |||||
/* If the so-called endpoint 3 is used, it can now be configured to any other | |||||
* endpoint number (except 0) with this macro. Default if undefined is 3. | |||||
*/ | |||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */ | |||||
/* The above macro defines the startup condition for data toggling on the | |||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1. | |||||
* Since the token is toggled BEFORE sending any data, the first packet is | |||||
* sent with the oposite value of this configuration! | |||||
*/ | |||||
#define USB_CFG_IMPLEMENT_HALT 0 | |||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature | |||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature, | |||||
* it is required by the standard. We have made it a config option because it | |||||
* bloats the code considerably. | |||||
*/ | |||||
#define USB_CFG_SUPPRESS_INTR_CODE 0 | |||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't | |||||
* want to send any data over them. If this macro is defined to 1, functions | |||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if | |||||
* you need the interrupt-in endpoints in order to comply to an interface | |||||
* (e.g. HID), but never want to send any data. This option saves a couple | |||||
* of bytes in flash memory and the transmit buffers in RAM. | |||||
*/ | |||||
#define USB_CFG_INTR_POLL_INTERVAL 10 | |||||
/* If you compile a version with endpoint 1 (interrupt-in), this is the poll | |||||
* interval. The value is in milliseconds and must not be less than 10 ms for | |||||
* low speed devices. | |||||
*/ | |||||
#define USB_CFG_IS_SELF_POWERED 0 | |||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the | |||||
* device is powered from the USB bus. | |||||
*/ | |||||
#define USB_CFG_MAX_BUS_POWER 500 | |||||
/* Set this variable to the maximum USB bus power consumption of your device. | |||||
* The value is in milliamperes. [It will be divided by two since USB | |||||
* communicates power requirements in units of 2 mA.] | |||||
*/ | |||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1 | |||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out | |||||
* transfers. Set it to 0 if you don't need it and want to save a couple of | |||||
* bytes. | |||||
*/ | |||||
#define USB_CFG_IMPLEMENT_FN_READ 0 | |||||
/* Set this to 1 if you need to send control replies which are generated | |||||
* "on the fly" when usbFunctionRead() is called. If you only want to send | |||||
* data from a static buffer, set it to 0 and return the data from | |||||
* usbFunctionSetup(). This saves a couple of bytes. | |||||
*/ | |||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0 | |||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints. | |||||
* You must implement the function usbFunctionWriteOut() which receives all | |||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number | |||||
* can be found in 'usbRxToken'. | |||||
*/ | |||||
#define USB_CFG_HAVE_FLOWCONTROL 0 | |||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition | |||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in | |||||
* usbdrv.h. | |||||
*/ | |||||
#define USB_CFG_DRIVER_FLASH_PAGE 0 | |||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page | |||||
* where the driver's constants (descriptors) are located. Or in other words: | |||||
* Define this to 1 for boot loaders on the ATMega128. | |||||
*/ | |||||
#define USB_CFG_LONG_TRANSFERS 0 | |||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes | |||||
* in a single control-in or control-out transfer. Note that the capability | |||||
* for long transfers increases the driver size. | |||||
*/ | |||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */ | |||||
/* This macro is a hook if you want to do unconventional things. If it is | |||||
* defined, it's inserted at the beginning of received message processing. | |||||
* If you eat the received message and don't want default processing to | |||||
* proceed, do a return after doing your things. One possible application | |||||
* (besides debugging) is to flash a status LED on each packet. | |||||
*/ | |||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */ | |||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has | |||||
* one parameter which distinguishes between the start of RESET state and its | |||||
* end. | |||||
*/ | |||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */ | |||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was | |||||
* received. | |||||
*/ | |||||
#define USB_COUNT_SOF 0 | |||||
/* define this macro to 1 if you need the global variable "usbSofCount" which | |||||
* counts SOF packets. This feature requires that the hardware interrupt is | |||||
* connected to D- instead of D+. | |||||
*/ | |||||
/* #ifdef __ASSEMBLER__ | |||||
* macro myAssemblerMacro | |||||
* in YL, TCNT0 | |||||
* sts timer0Snapshot, YL | |||||
* endm | |||||
* #endif | |||||
* #define USB_SOF_HOOK myAssemblerMacro | |||||
* This macro (if defined) is executed in the assembler module when a | |||||
* Start Of Frame condition is detected. It is recommended to define it to | |||||
* the name of an assembler macro which is defined here as well so that more | |||||
* than one assembler instruction can be used. The macro may use the register | |||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages | |||||
* immediately after an SOF pulse may be lost and must be retried by the host. | |||||
* What can you do with this hook? Since the SOF signal occurs exactly every | |||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in | |||||
* designs running on the internal RC oscillator. | |||||
* Please note that Start Of Frame detection works only if D- is wired to the | |||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES! | |||||
*/ | |||||
#define USB_CFG_CHECK_DATA_TOGGLING 0 | |||||
/* define this macro to 1 if you want to filter out duplicate data packets | |||||
* sent by the host. Duplicates occur only as a consequence of communication | |||||
* errors, when the host does not receive an ACK. Please note that you need to | |||||
* implement the filtering yourself in usbFunctionWriteOut() and | |||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable | |||||
* for each control- and out-endpoint to check for duplicate packets. | |||||
*/ | |||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0 | |||||
/* define this macro to 1 if you want the function usbMeasureFrameLength() | |||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator. | |||||
*/ | |||||
#define USB_USE_FAST_CRC 0 | |||||
/* The assembler module has two implementations for the CRC algorithm. One is | |||||
* faster, the other is smaller. This CRC routine is only used for transmitted | |||||
* messages where timing is not critical. The faster routine needs 31 cycles | |||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine | |||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and | |||||
* run the AVR close to its limit. | |||||
*/ | |||||
/* -------------------------- Device Description --------------------------- */ | |||||
#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF) | |||||
/* USB vendor ID for the device, low byte first. If you have registered your | |||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free | |||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules! | |||||
* *** IMPORTANT NOTE *** | |||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices | |||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand | |||||
* the implications! | |||||
*/ | |||||
#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF) | |||||
/* This is the ID of the product, low byte first. It is interpreted in the | |||||
* scope of the vendor ID. If you have registered your own VID with usb.org | |||||
* or if you have licensed a PID from somebody else, define it here. Otherwise | |||||
* you may use one of obdev's free shared VID/PID pairs. See the file | |||||
* USB-IDs-for-free.txt for details! | |||||
* *** IMPORTANT NOTE *** | |||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices | |||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand | |||||
* the implications! | |||||
*/ | |||||
#define USB_CFG_DEVICE_VERSION 0x00, 0x01 | |||||
/* Version number of the device: Minor number first, then major number. | |||||
*/ | |||||
#define USB_CFG_VENDOR_NAME 't', '.', 'm', '.', 'k', '.' | |||||
#define USB_CFG_VENDOR_NAME_LEN 6 | |||||
/* These two values define the vendor name returned by the USB device. The name | |||||
* must be given as a list of characters under single quotes. The characters | |||||
* are interpreted as Unicode (UTF-16) entities. | |||||
* If you don't want a vendor name string, undefine these macros. | |||||
* ALWAYS define a vendor name containing your Internet domain name if you use | |||||
* obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for | |||||
* details. | |||||
*/ | |||||
#define USB_CFG_DEVICE_NAME 'a', 'a', 'r', 'd', 'v', 'a', 'r', 'k', ' ', 'V', '-', 'U', 'S', 'B', ' ', 'k', 'e', 'y', 'b', 'o', 'a', 'r', 'd' | |||||
#define USB_CFG_DEVICE_NAME_LEN 23 | |||||
/* Same as above for the device name. If you don't want a device name, undefine | |||||
* the macros. See the file USB-IDs-for-free.txt before you assign a name if | |||||
* you use a shared VID/PID. | |||||
*/ | |||||
/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */ | |||||
/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */ | |||||
/* Same as above for the serial number. If you don't want a serial number, | |||||
* undefine the macros. | |||||
* It may be useful to provide the serial number through other means than at | |||||
* compile time. See the section about descriptor properties below for how | |||||
* to fine tune control over USB descriptors such as the string descriptor | |||||
* for the serial number. | |||||
*/ | |||||
#define USB_CFG_DEVICE_CLASS 0 | |||||
#define USB_CFG_DEVICE_SUBCLASS 0 | |||||
/* See USB specification if you want to conform to an existing device class. | |||||
* Class 0xff is "vendor specific". | |||||
*/ | |||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */ | |||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */ | |||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */ | |||||
/* See USB specification if you want to conform to an existing device class or | |||||
* protocol. The following classes must be set at interface level: | |||||
* HID class is 3, no subclass and protocol required (but may be useful!) | |||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM | |||||
*/ | |||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0 | |||||
/* Define this to the length of the HID report descriptor, if you implement | |||||
* an HID device. Otherwise don't define it or define it to 0. | |||||
* If you use this define, you must add a PROGMEM character array named | |||||
* "usbHidReportDescriptor" to your code which contains the report descriptor. | |||||
* Don't forget to keep the array and this define in sync! | |||||
*/ | |||||
/* #define USB_PUBLIC static */ | |||||
/* Use the define above if you #include usbdrv.c instead of linking against it. | |||||
* This technique saves a couple of bytes in flash memory. | |||||
*/ | |||||
/* ------------------- Fine Control over USB Descriptors ------------------- */ | |||||
/* If you don't want to use the driver's default USB descriptors, you can | |||||
* provide our own. These can be provided as (1) fixed length static data in | |||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at | |||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more | |||||
* information about this function. | |||||
* Descriptor handling is configured through the descriptor's properties. If | |||||
* no properties are defined or if they are 0, the default descriptor is used. | |||||
* Possible properties are: | |||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched | |||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is | |||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if | |||||
* you want RAM pointers. | |||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found | |||||
* in static memory is in RAM, not in flash memory. | |||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash), | |||||
* the driver must know the descriptor's length. The descriptor itself is | |||||
* found at the address of a well known identifier (see below). | |||||
* List of static descriptor names (must be declared PROGMEM if in flash): | |||||
* char usbDescriptorDevice[]; | |||||
* char usbDescriptorConfiguration[]; | |||||
* char usbDescriptorHidReport[]; | |||||
* char usbDescriptorString0[]; | |||||
* int usbDescriptorStringVendor[]; | |||||
* int usbDescriptorStringDevice[]; | |||||
* int usbDescriptorStringSerialNumber[]; | |||||
* Other descriptors can't be provided statically, they must be provided | |||||
* dynamically at runtime. | |||||
* | |||||
* Descriptor properties are or-ed or added together, e.g.: | |||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18)) | |||||
* | |||||
* The following descriptors are defined: | |||||
* USB_CFG_DESCR_PROPS_DEVICE | |||||
* USB_CFG_DESCR_PROPS_CONFIGURATION | |||||
* USB_CFG_DESCR_PROPS_STRINGS | |||||
* USB_CFG_DESCR_PROPS_STRING_0 | |||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR | |||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT | |||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER | |||||
* USB_CFG_DESCR_PROPS_HID | |||||
* USB_CFG_DESCR_PROPS_HID_REPORT | |||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver) | |||||
* | |||||
* Note about string descriptors: String descriptors are not just strings, they | |||||
* are Unicode strings prefixed with a 2 byte header. Example: | |||||
* int serialNumberDescriptor[] = { | |||||
* USB_STRING_DESCRIPTOR_HEADER(6), | |||||
* 'S', 'e', 'r', 'i', 'a', 'l' | |||||
* }; | |||||
*/ | |||||
#define USB_CFG_DESCR_PROPS_DEVICE 0 | |||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC | |||||
//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0 | |||||
#define USB_CFG_DESCR_PROPS_STRINGS 0 | |||||
#define USB_CFG_DESCR_PROPS_STRING_0 0 | |||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0 | |||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0 | |||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0 | |||||
//#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC | |||||
#define USB_CFG_DESCR_PROPS_HID 0 | |||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC | |||||
//#define USB_CFG_DESCR_PROPS_HID_REPORT 0 | |||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0 | |||||
/* ----------------------- Optional MCU Description ------------------------ */ | |||||
/* The following configurations have working defaults in usbdrv.h. You | |||||
* usually don't need to set them explicitly. Only if you want to run | |||||
* the driver on a device which is not yet supported or with a compiler | |||||
* which is not fully supported (such as IAR C) or if you use a differnt | |||||
* interrupt than INT0, you may have to define some of these. | |||||
*/ | |||||
/* #define USB_INTR_CFG MCUCR */ | |||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */ | |||||
/* #define USB_INTR_CFG_CLR 0 */ | |||||
/* #define USB_INTR_ENABLE GIMSK */ | |||||
/* #define USB_INTR_ENABLE_BIT INT0 */ | |||||
/* #define USB_INTR_PENDING GIFR */ | |||||
/* #define USB_INTR_PENDING_BIT INTF0 */ | |||||
/* #define USB_INTR_VECTOR INT0_vect */ | |||||
#endif /* __usbconfig_h_included__ */ | |||||