tmk
7 years ago
11 changed files with 86 additions and 307 deletions
+ 34
- 25
converter/ps2_usb/Makefile
View File
| @@ -1,31 +1,39 @@ | |||
| # | |||
| # Makefile for Teensy | |||
| # | |||
| # Target file name (without extension). | |||
| TARGET = ps2_usb_lufa | |||
| TARGET ?= ps2_usb | |||
| # Directory common source filess exist | |||
| TMK_DIR = ../../tmk_core | |||
| TMK_DIR ?= ../../tmk_core | |||
| # Directory keyboard dependent files exist | |||
| TARGET_DIR = . | |||
| TARGET_DIR ?= . | |||
| # project specific files | |||
| SRC = matrix.c \ | |||
| SRC ?= matrix.c \ | |||
| led.c | |||
| # | |||
| # Keymap file | |||
| # | |||
| ifdef UNIMAP_ENABLE | |||
| KEYMAP_FILE = unimap | |||
| else | |||
| ifdef ACTIONMAP_ENABLE | |||
| KEYMAP_FILE = actionmap | |||
| else | |||
| KEYMAP_FILE = keymap | |||
| endif | |||
| endif | |||
| ifdef KEYMAP | |||
| SRC := keymap_$(KEYMAP).c $(SRC) | |||
| SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC) | |||
| else | |||
| SRC := keymap_plain.c $(SRC) | |||
| SRC := $(KEYMAP_FILE)_plain.c $(SRC) | |||
| endif | |||
| CONFIG_H = config.h | |||
| CONFIG_H ?= config.h | |||
| # MCU name | |||
| #MCU = at90usb1287 | |||
| MCU = atmega32u4 | |||
| MCU ?= atmega32u2 | |||
| # Processor frequency. | |||
| # This will define a symbol, F_CPU, in all source code files equal to the | |||
| @@ -38,14 +46,14 @@ MCU = atmega32u4 | |||
| # does not *change* the processor frequency - it should merely be updated to | |||
| # reflect the processor speed set externally so that the code can use accurate | |||
| # software delays. | |||
| F_CPU = 16000000 | |||
| F_CPU ?= 16000000 | |||
| # | |||
| # LUFA specific | |||
| # | |||
| # Target architecture (see library "Board Types" documentation). | |||
| ARCH = AVR8 | |||
| ARCH ?= AVR8 | |||
| # Input clock frequency. | |||
| # This will define a symbol, F_USB, in all source code files equal to the | |||
| @@ -58,7 +66,7 @@ ARCH = AVR8 | |||
| # | |||
| # If no clock division is performed on the input clock inside the AVR (via the | |||
| # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
| F_USB = $(F_CPU) | |||
| F_USB ?= $(F_CPU) | |||
| # Interrupt driven control endpoint task(+60) | |||
| #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
| @@ -70,25 +78,26 @@ F_USB = $(F_CPU) | |||
| # Atmel DFU loader 4096 | |||
| # LUFA bootloader 4096 | |||
| # USBaspLoader 2048 | |||
| OPT_DEFS += -DBOOTLOADER_SIZE=512 | |||
| BOOTLOADER_SIZE ?= 4096 | |||
| OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE) | |||
| # Build Options | |||
| # comment out to disable the options. | |||
| # | |||
| #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
| MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
| EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
| CONSOLE_ENABLE = yes # Console for debug(+400) | |||
| COMMAND_ENABLE = yes # Commands for debug and configuration | |||
| NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |||
| BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) | |||
| MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) | |||
| EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) | |||
| CONSOLE_ENABLE ?= yes # Console for debug(+400) | |||
| COMMAND_ENABLE ?= yes # Commands for debug and configuration | |||
| NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA | |||
| # PS/2 Options | |||
| # | |||
| #PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) | |||
| PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin | |||
| #PS2_USE_BUSYWAIT = yes # uses primitive reference code | |||
| #PS2_USE_USART ?= yes # uses hardware USART engine for PS/2 signal receive(recomened) | |||
| PS2_USE_INT ?= yes # uses external interrupt for falling edge of PS/2 clock pin | |||
| #PS2_USE_BUSYWAIT ?= yes # uses primitive reference code | |||
| # Optimize size but this may cause error "relocation truncated to fit" | |||
+ 0
- 74
converter/ps2_usb/Makefile.pjrc
View File
| @@ -1,74 +0,0 @@ | |||
| # Target file name (without extension). | |||
| TARGET = ps2_usb_pjrc | |||
| # Directory common source filess exist | |||
| TMK_DIR = ../../tmk_core | |||
| # Directory keyboard dependent files exist | |||
| TARGET_DIR = . | |||
| # keyboard dependent files | |||
| SRC = matrix.c \ | |||
| led.c | |||
| ifdef KEYMAP | |||
| SRC := keymap_$(KEYMAP).c $(SRC) | |||
| else | |||
| SRC := keymap_plain.c $(SRC) | |||
| endif | |||
| CONFIG_H = config.h | |||
| # MCU name, you MUST set this to match the board you are using | |||
| # type "make clean" after changing this, so all files will be rebuilt | |||
| #MCU = at90usb162 # Teensy 1.0 | |||
| MCU = atmega32u4 # Teensy 2.0 | |||
| #MCU = at90usb646 # Teensy++ 1.0 | |||
| #MCU = at90usb1286 # Teensy++ 2.0 | |||
| # Processor frequency. | |||
| # Normally the first thing your program should do is set the clock prescaler, | |||
| # so your program will run at the correct speed. You should also set this | |||
| # variable to same clock speed. The _delay_ms() macro uses this, and many | |||
| # examples use this variable to calculate timings. Do not add a "UL" here. | |||
| F_CPU = 16000000 | |||
| # Boot Section Size in *bytes* | |||
| # Teensy halfKay 512 | |||
| # Teensy++ halfKay 1024 | |||
| # Atmel DFU loader 4096 | |||
| # LUFA bootloader 4096 | |||
| # USBaspLoader 2048 | |||
| OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
| # Build Options | |||
| # *Comment out* to disable the options. | |||
| # | |||
| #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
| MOUSEKEY_ENABLE = yes # Mouse keys | |||
| EXTRAKEY_ENABLE = yes # Audio control and System control | |||
| CONSOLE_ENABLE = yes # Console for debug(+400) | |||
| COMMAND_ENABLE = yes # Commands for debug and configuration | |||
| NKRO_ENABLE = yes # USB Nkey Rollover | |||
| # PS/2 Options | |||
| # | |||
| #PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) | |||
| #PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin | |||
| PS2_USE_BUSYWAIT = yes # uses primitive reference code | |||
| # Search Path | |||
| VPATH += $(TARGET_DIR) | |||
| VPATH += $(TMK_DIR) | |||
| include $(TMK_DIR)/protocol.mk | |||
| include $(TMK_DIR)/protocol/pjrc.mk | |||
| include $(TMK_DIR)/common.mk | |||
| include $(TMK_DIR)/rules.mk | |||
+ 17
- 0
converter/ps2_usb/Makefile.rev1
View File
| @@ -0,0 +1,17 @@ | |||
| TARGET ?= ps2_usb_rev1 | |||
| MCU = atmega32u4 | |||
| CONFIG_H = config_rev1.h | |||
| BOOTLOADER_SIZE = 4096 | |||
| BOOTMAGIC_ENABLE ?= no | |||
| MOUSEKEY_ENABLE ?= yes | |||
| EXTRAKEY_ENABLE ?= yes | |||
| CONSOLE_ENABLE ?= yes | |||
| COMMAND_ENABLE ?= yes | |||
| NKRO_ENABLE ?= yes | |||
| PS2_USE_USART = yes | |||
| PS2_USE_INT = no | |||
| PS2_USE_BUSYWAIT = no | |||
| include Makefile | |||
+ 17
- 0
converter/ps2_usb/Makefile.rev2
View File
| @@ -0,0 +1,17 @@ | |||
| TARGET ?= ps2_usb_rev2 | |||
| MCU = atmega32u2 | |||
| CONFIG_H = config_rev2.h | |||
| BOOTLOADER_SIZE = 4096 | |||
| BOOTMAGIC_ENABLE ?= no | |||
| MOUSEKEY_ENABLE ?= no | |||
| EXTRAKEY_ENABLE ?= yes | |||
| CONSOLE_ENABLE ?= yes | |||
| COMMAND_ENABLE ?= yes | |||
| NKRO_ENABLE ?= yes | |||
| PS2_USE_USART = no | |||
| PS2_USE_INT = yes | |||
| PS2_USE_BUSYWAIT = no | |||
| include Makefile | |||
+ 0
- 97
converter/ps2_usb/Makefile.tmk_rev1
View File
| @@ -1,97 +0,0 @@ | |||
| # | |||
| # Makefile for TMK keyboard converter rev2 | |||
| # https://github.com/tmk/keyboard_converter#pcb-rev1 | |||
| # | |||
| # Target file name (without extension). | |||
| TARGET = ps2_usb_tmk_rev1 | |||
| # Directory common source filess exist | |||
| TMK_DIR = ../../tmk_core | |||
| # Directory keyboard dependent files exist | |||
| TARGET_DIR = . | |||
| # project specific files | |||
| SRC = matrix.c \ | |||
| led.c | |||
| ifdef KEYMAP | |||
| SRC := keymap_$(KEYMAP).c $(SRC) | |||
| else | |||
| SRC := keymap_plain.c $(SRC) | |||
| endif | |||
| CONFIG_H = config_tmk_rev1.h | |||
| # MCU name | |||
| MCU = atmega32u4 | |||
| # Processor frequency. | |||
| # This will define a symbol, F_CPU, in all source code files equal to the | |||
| # processor frequency in Hz. You can then use this symbol in your source code to | |||
| # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
| # automatically to create a 32-bit value in your source code. | |||
| # | |||
| # This will be an integer division of F_USB below, as it is sourced by | |||
| # F_USB after it has run through any CPU prescalers. Note that this value | |||
| # does not *change* the processor frequency - it should merely be updated to | |||
| # reflect the processor speed set externally so that the code can use accurate | |||
| # software delays. | |||
| F_CPU = 16000000 | |||
| # | |||
| # LUFA specific | |||
| # | |||
| # Target architecture (see library "Board Types" documentation). | |||
| ARCH = AVR8 | |||
| # Input clock frequency. | |||
| # This will define a symbol, F_USB, in all source code files equal to the | |||
| # input clock frequency (before any prescaling is performed) in Hz. This value may | |||
| # differ from F_CPU if prescaling is used on the latter, and is required as the | |||
| # raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
| # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
| # at the end, this will be done automatically to create a 32-bit value in your | |||
| # source code. | |||
| # | |||
| # If no clock division is performed on the input clock inside the AVR (via the | |||
| # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
| F_USB = $(F_CPU) | |||
| # Boot Section Size in *bytes* | |||
| # Teensy halfKay 512 | |||
| # Teensy++ halfKay 1024 | |||
| # Atmel DFU loader 4096 | |||
| # LUFA bootloader 4096 | |||
| # USBaspLoader 2048 | |||
| OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
| # Build Options | |||
| # comment out to disable the options. | |||
| # | |||
| #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
| MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
| EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
| CONSOLE_ENABLE = yes # Console for debug(+400) | |||
| COMMAND_ENABLE = yes # Commands for debug and configuration | |||
| #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |||
| # PS/2 Options | |||
| # | |||
| PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) | |||
| #PS2_USE_BUSYWAIT = yes # uses primitive reference code | |||
| # Search Path | |||
| VPATH += $(TARGET_DIR) | |||
| VPATH += $(TMK_DIR) | |||
| include $(TMK_DIR)/protocol.mk | |||
| include $(TMK_DIR)/protocol/lufa.mk | |||
| include $(TMK_DIR)/common.mk | |||
| include $(TMK_DIR)/rules.mk | |||
+ 0
- 97
converter/ps2_usb/Makefile.tmk_rev2
View File
| @@ -1,97 +0,0 @@ | |||
| # | |||
| # Makefile for TMK keyboard converter rev2 | |||
| # https://github.com/tmk/keyboard_converter#pcb-rev2 | |||
| # | |||
| # Target file name (without extension). | |||
| TARGET = ps2_usb_tmk_rev2 | |||
| # Directory common source filess exist | |||
| TMK_DIR = ../../tmk_core | |||
| # Directory keyboard dependent files exist | |||
| TARGET_DIR = . | |||
| # project specific files | |||
| SRC = matrix.c \ | |||
| led.c | |||
| ifdef KEYMAP | |||
| SRC := keymap_$(KEYMAP).c $(SRC) | |||
| else | |||
| SRC := keymap_plain.c $(SRC) | |||
| endif | |||
| CONFIG_H = config_tmk_rev2.h | |||
| # MCU name | |||
| MCU = atmega32u2 | |||
| # Processor frequency. | |||
| # This will define a symbol, F_CPU, in all source code files equal to the | |||
| # processor frequency in Hz. You can then use this symbol in your source code to | |||
| # calculate timings. Do NOT tack on a 'UL' at the end, this will be done | |||
| # automatically to create a 32-bit value in your source code. | |||
| # | |||
| # This will be an integer division of F_USB below, as it is sourced by | |||
| # F_USB after it has run through any CPU prescalers. Note that this value | |||
| # does not *change* the processor frequency - it should merely be updated to | |||
| # reflect the processor speed set externally so that the code can use accurate | |||
| # software delays. | |||
| F_CPU = 16000000 | |||
| # | |||
| # LUFA specific | |||
| # | |||
| # Target architecture (see library "Board Types" documentation). | |||
| ARCH = AVR8 | |||
| # Input clock frequency. | |||
| # This will define a symbol, F_USB, in all source code files equal to the | |||
| # input clock frequency (before any prescaling is performed) in Hz. This value may | |||
| # differ from F_CPU if prescaling is used on the latter, and is required as the | |||
| # raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
| # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
| # at the end, this will be done automatically to create a 32-bit value in your | |||
| # source code. | |||
| # | |||
| # If no clock division is performed on the input clock inside the AVR (via the | |||
| # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
| F_USB = $(F_CPU) | |||
| # Boot Section Size in *bytes* | |||
| # Teensy halfKay 512 | |||
| # Teensy++ halfKay 1024 | |||
| # Atmel DFU loader 4096 | |||
| # LUFA bootloader 4096 | |||
| # USBaspLoader 2048 | |||
| OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
| # Build Options | |||
| # comment out to disable the options. | |||
| # | |||
| #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
| MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
| EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
| CONSOLE_ENABLE = yes # Console for debug(+400) | |||
| COMMAND_ENABLE = yes # Commands for debug and configuration | |||
| #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |||
| # PS/2 Options | |||
| # | |||
| PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin | |||
| #PS2_USE_BUSYWAIT = yes # uses primitive reference code | |||
| # Search Path | |||
| VPATH += $(TARGET_DIR) | |||
| VPATH += $(TMK_DIR) | |||
| include $(TMK_DIR)/protocol.mk | |||
| include $(TMK_DIR)/protocol/lufa.mk | |||
| include $(TMK_DIR)/common.mk | |||
| include $(TMK_DIR)/rules.mk | |||
+ 5
- 0
converter/ps2_usb/Makefile.unimap.rev1
View File
| @@ -0,0 +1,5 @@ | |||
| TARGET = ps2_usb_rev1_unimap | |||
| UNIMAP_ENABLE = yes | |||
| KEYMAP_SECTION_ENABLE = yes | |||
| include Makefile.rev1 | |||
+ 5
- 0
converter/ps2_usb/Makefile.unimap.rev2
View File
| @@ -0,0 +1,5 @@ | |||
| TARGET = ps2_usb_rev2_unimap | |||
| UNIMAP_ENABLE = yes | |||
| KEYMAP_SECTION_ENABLE = yes | |||
| include Makefile.rev2 | |||
+ 8
- 14
converter/ps2_usb/README.md
View File
| @@ -5,36 +5,30 @@ This firmware converts PS/2 keyboard protocol to USB.(It supports Scan Code Set | |||
| Connect Wires | |||
| ------------- | |||
| In case of Teensy2.0(ATMega32U4): | |||
| 1. Connect **Vcc** and **GND**. | |||
| 2. Connect **Clock** and **Data** line. | |||
| - **Interrupt**: **Clock** is on `PD1` and **Data** on `PD0`.(Recommended. Soarer's converter compatible) | |||
| - **Busywait**: **Clock** is on `PD1` and **Data** on `PD0`. | |||
| - **USART**: **Clock** is on `PD5` and **Data** on `PD2`. | |||
| 3. Optionally you need pull-up resistor. 1K-10K Ohm is OK. | |||
| 3. You need pull-up resistors. 1K-10K Ohm would be fine. | |||
| To change pin configuration edit **config.h** and **Makefile**. | |||
| Build Firmware | |||
| -------------- | |||
| For **PJRC Teensy** just run `make`: | |||
| $ make clean | |||
| $ make | |||
| To select keymap: | |||
| For **TMK converter Rev.2**: | |||
| $ make clean | |||
| $ make KEYMAP=[plain|jis|spacefn|...] | |||
| $ make -f Makefile.rev2 clean | |||
| $ make -f Makefile.rev2 KEYMAP=plain | |||
| After that you will find HEX file `ps2_usb_lufa.hex` in current directory. | |||
| To program firmware push the button on converter and run: | |||
| $ make -f Makefile.rev2 KEYMAP=plain dfu | |||
| - For **TMK converter Rev.1** use `make -f Makefile.tmk_rev1` instead of `make` and HEX file is `ps2_usb_tmk_rev1.hex`. | |||
| - For **TMK converter Rev.2** use `make -f Makefile.tmk_rev2` instead of `make` and HEX file is `ps2_usb_tmk_rev2.hex`. | |||
| - For **TMK converter Rev.1** use `make -f Makefile.rev1` instead. | |||
| - To select keymap use `jis`, `spacefn` or your own in place of `plain`. | |||
| Keymap | |||
converter/ps2_usb/config_tmk_rev1.h → converter/ps2_usb/config_rev1.h
View File
converter/ps2_usb/config_tmk_rev2.h → converter/ps2_usb/config_rev2.h
View File
Loading…