7 years ago · d96f295106
--- a/keyboard/hhkb/Makefile
+++ b/keyboard/hhkb/Makefile
 #----------------------------------------------------------------------------
 # Target file name (without extension).
 TARGET ?= hhkb_lufa
 TARGET ?= hhkb
 # Directory common source filess exist
 TMK_DIR ?= ../../tmk_core
 SRC ?= matrix.c \
 led.c
 ifeq (yes,$(strip $(RN42_ENABLE)))
 CONFIG_H ?= config_rn42.h
 else
 CONFIG_H ?= config.h
 endif
 # MCU name
 # PJRC Teensy++ 2.0
 #MCU = at90usb1286
 # TMK Alt Controller or PJRC Teensy 2.0
 MCU ?= atmega32u4
 # Processor frequency.
 # Build Options
 # comment out to disable the options.
 #
 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
 MOUSEKEY_ENABLE = yes # Mouse keys
 EXTRAKEY_ENABLE = yes # Audio control and System control
 CONSOLE_ENABLE = yes # Console for debug
 COMMAND_ENABLE = yes # Commands for debug and configuration
 NKRO_ENABLE = yes # USB Nkey Rollover
 #KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
 #HHKB_JP = yes # HHKB JP support
 #UNIMAP_ENABLE = yes
 #ACTIONMAP_ENABLE = yes # Use 16bit actionmap instead of 8bit keymap
 #KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
 #BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration
 MOUSEKEY_ENABLE ?= yes # Mouse keys
 EXTRAKEY_ENABLE ?= yes # Audio control and System control
 CONSOLE_ENABLE ?= yes # Console for debug
 COMMAND_ENABLE ?= yes # Commands for debug and configuration
 NKRO_ENABLE ?= yes # USB Nkey Rollover
 #HHKB_JP ?= yes # HHKB JP support
 #UNIMAP_ENABLE ?= yes # Universal keymap
 #ACTIONMAP_ENABLE ?= yes # Use 16bit actionmap instead of 8bit keymap
 #KEYMAP_SECTION_ENABLE ?= yes # fixed address keymap for keymap editor
 #OPT_DEFS += -DNO_ACTION_TAPPING
 #OPT_DEFS += -DNO_ACTION_LAYER
 #
 # Keymap file
 #
 ifdef UNIMAP_ENABLE
 ifeq (yes,$(strip $(UNIMAP_ENABLE)))
 KEYMAP_FILE = unimap
 else
 ifdef ACTIONMAP_ENABLE
 ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
 KEYMAP_FILE = actionmap
 else
 KEYMAP_FILE = keymap
 ifdef KEYMAP
 SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
 else
 ifdef HHKB_JP
 ifeq (yes,$(strip $(HHKB_JP)))
 SRC := $(KEYMAP_FILE)_jp.c $(SRC)
 else 
 SRC := $(KEYMAP_FILE)_hhkb.c $(SRC)
 VPATH += $(TARGET_DIR)
 VPATH += $(TMK_DIR)
 ifeq (yes,$(strip $(RN42_ENABLE)))
 include rn42.mk
 include $(TMK_DIR)/protocol.mk
 endif
 include $(TMK_DIR)/protocol/lufa.mk
 include $(TMK_DIR)/common.mk
 include $(TMK_DIR)/rules.mk
--- a/keyboard/hhkb/Makefile.keymap_editor
+++ b/keyboard/hhkb/Makefile.keymap_editor
 # build firmware for keymap editor
 #
 TARGET = hhkb_editor
 KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
 include Makefile
--- a/keyboard/hhkb/Makefile.rn42.keymap_editor
+++ b/keyboard/hhkb/Makefile.rn42.keymap_editor
 # build firmware for keymap editor
 #
 TARGET = hhkb_rn42_editor
 KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
 include Makefile.rn42
--- a/keyboard/hhkb/Makefile.jp
+++ b/keyboard/hhkb/Makefile.jp
 TARGET = hhkb_jp
 HHKB_JP = yes
 NKRO_ENABLE = no
 include Makefile
--- a/keyboard/hhkb/Makefile.rn42
+++ b/keyboard/hhkb/Makefile.rn42
 #----------------------------------------------------------------------------
 # On command line:
 #
 # make all = Make software.
 #
 # make clean = Clean out built project files.
 #
 # make coff = Convert ELF to AVR COFF.
 #
 # make extcoff = Convert ELF to AVR Extended COFF.
 #
 # make program = Download the hex file to the device.
 # Please customize your programmer settings(PROGRAM_CMD)
 #
 # make teensy = Download the hex file to the device, using teensy_loader_cli.
 # (must have teensy_loader_cli installed).
 #
 # make dfu = Download the hex file to the device, using dfu-programmer (must
 # have dfu-programmer installed).
 #
 # make flip = Download the hex file to the device, using Atmel FLIP (must
 # have Atmel FLIP installed).
 #
 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
 # (must have dfu-programmer installed).
 #
 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
 # (must have Atmel FLIP installed).
 #
 # make debug = Start either simulavr or avarice as specified for debugging, 
 # with avr-gdb or avr-insight as the front end for debugging.
 #
 # make filename.s = Just compile filename.c into the assembler code only.
 #
 # make filename.i = Create a preprocessed source file for use in submitting
 # bug reports to the GCC project.
 #
 # To rebuild project do "make clean" then "make all".
 #----------------------------------------------------------------------------
 # Target file name (without extension).
 TARGET = hhkb_rn42
 # Directory common source filess exist
 TMK_DIR = ../../tmk_core
 # Directory keyboard dependent files exist
 TARGET_DIR = .
 # List C source files here. (C dependencies are automatically generated.)
 SRC += matrix.c \
 led.c
 CONFIG_H = config_rn42.h
 # MCU name
 MCU = atmega32u4
 # Processor frequency.
 # This will define a symbol, F_CPU, in all source code files equal to the
 # processor frequency in Hz. You can then use this symbol in your source code to
 # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
 # automatically to create a 32-bit value in your source code.
 #
 # This will be an integer division of F_USB below, as it is sourced by
 # F_USB after it has run through any CPU prescalers. Note that this value
 # does not *change* the processor frequency - it should merely be updated to
 # reflect the processor speed set externally so that the code can use accurate
 # software delays.
 F_CPU = 16000000
 #
 # LUFA specific
 #
 # Target architecture (see library "Board Types" documentation).
 ARCH = AVR8
 # Input clock frequency.
 # This will define a symbol, F_USB, in all source code files equal to the
 # input clock frequency (before any prescaling is performed) in Hz. This value may
 # differ from F_CPU if prescaling is used on the latter, and is required as the
 # raw input clock is fed directly to the PLL sections of the AVR for high speed
 # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
 # at the end, this will be done automatically to create a 32-bit value in your
 # source code.
 #
 # If no clock division is performed on the input clock inside the AVR (via the
 # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
 # Interrupt driven control endpoint task
 #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
 # Boot Section Size in *bytes*
 # Teensy halfKay 512
 # Teensy++ halfKay 1024
 # Atmel DFU loader 4096 (TMK Alt Controller)
 # LUFA bootloader 4096
 # USBaspLoader 2048
 OPT_DEFS += -DBOOTLOADER_SIZE=4096
 # Build Options
 # comment out to disable the options.
 #
 BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
 MOUSEKEY_ENABLE = yes # Mouse keys
 EXTRAKEY_ENABLE = yes # Audio control and System control
 CONSOLE_ENABLE = yes # Console for debug
 COMMAND_ENABLE = yes # Commands for debug and configuration
 NKRO_ENABLE = yes # USB Nkey Rollover
 #KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
 #HHKB_JP = yes # HHKB JP support
 #
 # Keymap file
 #
 ifdef KEYMAP
 SRC := keymap_$(KEYMAP).c $(SRC)
 else
 ifdef HHKB_JP
 SRC := keymap_jp.c $(SRC)
 else 
 SRC := keymap_hhkb.c $(SRC)
 endif
 endif
 ifneq (, $(or $(findstring keymap_jp.c, $(SRC)), $(findstring yes, $(HHKB_JP))))
 OPT_DEFS += -DHHKB_JP
 endif
 # Search Path
 VPATH += $(TARGET_DIR)
 VPATH += $(TMK_DIR)
 include rn42.mk
 include $(TMK_DIR)/protocol.mk
 include $(TMK_DIR)/protocol/lufa.mk
 include $(TMK_DIR)/common.mk
 include $(TMK_DIR)/rules.mk
 debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
 debug-on: all
 debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
 debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))
 debug-off: all
 TARGET ?= hhkb_rn42
 CONFIG_H ?= config_rn42.h
 RN42_ENABLE ?= yes
 NKRO_ENABLE ?= no
 include Makefile
--- a/keyboard/hhkb/Makefile.rn42.jp
+++ b/keyboard/hhkb/Makefile.rn42.jp
 HHKB_JP = yes
 include Makefile.rn42
--- a/keyboard/hhkb/Makefile.unimap.jp
+++ b/keyboard/hhkb/Makefile.unimap.jp
 HHKB_JP = yes
 UNIMAP_ENABLE = yes
 KEYMAP_SECTION_ENABLE = yes
 NKRO_ENABLE = no
 include Makefile
--- a/keyboard/hhkb/Makefile.unimap.rn42
+++ b/keyboard/hhkb/Makefile.unimap.rn42
 TARGET = hhkb_rn42_unimap
 UNIMAP_ENABLE = yes
 KEYMAP_SECTION_ENABLE = yes
 include Makefile.rn42
--- a/keyboard/hhkb/Makefile.unimap.rn42.jp
+++ b/keyboard/hhkb/Makefile.unimap.rn42.jp
 TARGET = hhkb_jp_rn42_unimap
 HHKB_JP = yes
 UNIMAP_ENABLE = yes
 KEYMAP_SECTION_ENABLE = yes
 include Makefile.rn42
--- a/keyboard/hhkb/binary/hhkb_jp_unimap.hex
+++ b/keyboard/hhkb/binary/hhkb_jp_unimap.hex
--- a/keyboard/hhkb/binary/hhkb_unimap.hex
+++ b/keyboard/hhkb/binary/hhkb_unimap.hex
--- a/keyboard/hhkb/not_supported/Makefile.pjrc
+++ b/keyboard/hhkb/not_supported/Makefile.pjrc
--- a/keyboard/hhkb/unimap_jp.c
+++ b/keyboard/hhkb/unimap_jp.c
 NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, 
 ZKHK, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO, NO,
 ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, JYEN,BSPC, NO, NO, NO, NO, NO, NO, NO,
 TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, BSLS, NO, NO, NO, NO, NO, NO, NO,
 TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, NO,  NO, NO, NO, NO, NO, NO, NO,
 LCTL,A, S, D, F, G, H, J, K, L, SCLN,QUOT, NUHS,ENT, NO, NO, NO, NO,
 LSFT,NO, Z, X, C, V, B, N, M, COMM,DOT, SLSH, RO, RSFT, UP, NO, NO, NO, NO,
 FN0, LGUI,LALT,MHEN, SPC, HENK,KANA,RALT,NO, NO, FN0, LEFT,DOWN,RGHT, NO, NO, NO

		HHKB_JP = yes			HHKB_JP = yes
		include Makefile.rn42			include Makefile.rn42