RN-42 Bluetooth Module Support ============================== Bluetooth controller board works with HHKB Pro2, JP, Type-S and Type-S JP and it supports both USB and Bluetooth as keyboard output protocol. Bluetooth module Roving Networks/Microchip RN-42 is installed on the board. RN-42: http://www.microchip.com/wwwproducts/Devices.aspx?product=RN42 Capabitlities: - USB keyboard functions completely equivarent to USB controller including mouse keys and NKRO. - Switching between USB and Bluetooth You can switch the two connections with BT switch or key combination. - RN-42 config mode You can change power/connection configuration of the module if needed. - Low battery alert Red LED turns on when low voltage. - RN-42 status indicator LED indicates status of Bluetooth connection. - Pairing The module stores up to 8 connections. - Auto connect The module connects the last connected device automatically. - iOS support works as keyboard with iPhone5. No tested completely. - Android support works as keyboard and mouse with Nexus5. No tested completely. - Mouse keys over BT Note that iOS doesn't accept mouse device. Limitations: - Short battery life Around 12hr with 1000mAh - No connection switching RN-42 auto-connects to the last connected device. Some of consumer products can switch between devices, for example Logitech K480. http://www.logitech.com/en-us/product/multi-device-keyboard-k480?crid=26 - HHKB JP requires case modification for BT switch and LEDs. without switch power controlled by MCU? Probably using 3.3V regulator enable pin power of RN-42 can be controlled. NOTE: - LIPO BATTERY IS VERY DANGEROUS, TAKE EXTRA CARE OF YOUR SAFETY AND PROPERTY. - RN-42 version 6.15 is supported. - No NKRO over Bluetooth - Check you country's wiress regulation and certification of RN-42. Bugs: Todos: Lipo Battery ------------ You can use 3.7V Lithium Ion battery with JST PH 2pin connector and protection circuit. Battery space inside HHKB is around 54mm x 50mm and its height is 7mm. Sparkfun 850mAh https://www.sparkfun.com/products/341 Sparkfun 1000mAh https://www.sparkfun.com/products/339 Sparkfun 2000mAh battery won't fit due to its size. Learn about Lipo battery: https://learn.adafruit.com/li-ion-and-lipoly-batteries LED Status ---------- Configuring 10 times per sec Startup/configuration timer 2 times per sec Discoverable/Inquiring/Idle once per sec Connected solid on RN-42 Magic Command -------------------- Magic key combination is 'LShift+RShift' by default in case of HHKB. Here is help. ----- Bluetooth RN-42 Help ----- i: RN-42 info b: battery voltage Del: enter/exit RN-42 config mode Slck: RN-42 initialize p: pairing u: toggle Force USB mode RN-42 info: displays information of the module on console. battery voltage: displays current voltage of battery and uptime. RN-42 initialize: does factory reset and configures RN-42 pairing: enters Pairing mode. toggle Force USB mode: switch between USB and Bluetooth RN-42 Config mode ----------------- You can tune/operate RN-42 yourself with config(command) mode. 1. hook up USB cable 2. run `hid_listen` command in console 3. turn on Bluetooth switch 4. press LShift+RShift+Delete(Fn+~) you will see output like followings: Entering config mode ... CMD v Ver 6.15 04/26/2013 (c) Roving Networks 5. do config with RN-42 commands. See documentations of RN-42. 6. to exit also press LShift+RShift+Delete(Fn+~) Exiting config mode ... --- END RN-42 Initial Configuration --------------------------- RN-42 is configured as SPP device at factory reset, you need to configure it as HID device. This is needed just once first time. 1. hook up USB cable 2. run `hid_listen` command in console 3. turn on Bluetooth switch 4. press LShift+RShift+ScrLk(Fn+O) you will see output like followings: Entering config mode ... CMD Ver 6.15 04/26/2013 (c) Roving Networks ECHO ON SF,1 AOK S-,TmkBT AOK SS,Keyboard/Mouse AOK SM,4 AOK SW,8000 AOK S~,6 AOK SH,003C AOK SY,FFF4 AOK R,1 Reboot! Exiting config mode ... 5. output of command 'X' after cofiguration Ver 6.15 04/26/2013 (c) Roving Networks ***Settings*** BTA=00066667BBE9 BTName=TmkBT-BBE9 Baudrt(SW4)=115K Mode =DTR Authen=1 PinCod=1234 Bonded=0 Rem=NONE SET ***ADVANCED Settings*** SrvName= Keyboard/Mouse SrvClass=0000 DevClass=1F00 InqWindw=0100 PagWindw=0100 CfgTimer=255 StatuStr=NULL HidFlags=3c DTRtimer=8 KeySwapr=0 ***OTHER Settings*** Profile= HID CfgChar= $ SniffEna=8000 LowPower=0 TX Power=fff4 IOPorts= 0 IOValues=0 Sleeptmr=0 DebugMod=0 RoleSwch=0 Switch to USB mode ------------------ You can switch between USB and Bluetooth with pressing 'LShift+RShift+u'. Pairing mode ------------ This disconnects current connect and enter pairing mode. For deveropment =============== RN-42 Serial Connection ----------------------- UART: 115200bps, 8bit, 1-stopbit, non-parity, no flow control SSP: 115200bps, 8bit, 1-stopbit, non-parity, no flow control(via Bluetooth) To enter command mode disconnect the module from host and type '$$$'.(you will see 'CMD') and type '+' to get local echo. To exit type '---'(you will see 'END'). RN-42 Commands -------------- S-,tmkBT // Device name SS,keyboard/mouse // service name SM,4 // Auto Connect DTR mode SW,8010 // Sniff enable 0x10*0.625ms=10ms; 50ms is laggish and not much power save S~,6 // HID profile S~,0 // SPP profile SH,003C // HID register SY,0004 // Transmit power SC,0000 // COD: 000005C0 (see HID spec/Bluegiga doc) SD,05C0 // bit 12-8 7 6 5-0 // 00101 1 1 0 // peripheral pointing keybaord joystick, gamepad, ... SM,6 // Pairing mode: auto connect SM,4 // Master mode: Connection can be controled with GPIO6 SF,1 // Factroy reset R,1 // reboot SR,Z // removes all remote addresses for reconnecting. // can be used to connect another host SR,I // registers last inquiry address Operation Modes --------------- SM,3 Auto Connect Master mode SM,4 Auto Connect DTR Mode uses GPIO6 to make and break connection(Mode =DTR) confirm: auto connect works and control connection with GPIO6 SM,5 Auto Connect ANY Mode (Mode =ANY) each time GPIO is set, make inquiry and connect to the first found device SM,6 automatically reconnect(Mode =Pair) confirm: auto connect works well but difficult to enter command mode. HID flag register ----------------- SH,0200 GH 10 0000 0000(0200) default 00 0011 1000(0038) Combo || | | |\_\____ number of paired devices to which the module can reconnect || | | \_______ send out reports over UART (0xFF ) || \__\_________ descriptor type |\______________ toggle virtual keyboard on iOS when first connected \_______________ Force HID mode if GPIO11 is high on power-up Descriptor type: 0000: keybaord 0001: Game Pad 0010: Mouse 0011: Combo 0100: Joystick 1xxx: reserved Out report - Indicator ---------------------- 0xFE 0x02 0x01 Apple iOS --------- Keyboard can be used with iPhone, but mouse cannot. Android ------- 3.7.1.5 Note: To connect with Android phone the modules must wake up 11ms every 2.5seconds. Power Management ---------------- Inquiry and Page window Idle or Active (3.1.1) Downside: delay in discovery or connection time SI, // set inquiry scan window(discovery) on/off duty? SJ, // set page scan window(connection) This reduces averaege power >20mA to 5mA(3mA in Sniff mode) Sniff mode Transmit Sniff mode is disabled by default and radio is active continuously when connected.(25-30mA) In Sniff mode the radio wakes up intermittently and sleeps in very low power mode.(2mA) SW, // set interval timer(*0.625ms) 0000-7FFF Deep sleep Idle (3.1.2) In this mode the module shuts down completly and only draws about 300uA. To enable this set the most signifant bit(0x8000) of Sniff interaval timer. SW,8320 // deep sleep enable(interval=0x320*0.625=500ms) In normal sleep the firmware is still running in idle mode, and wakes up about 20 times per second to check ports, update LEDs, etc. During deep sleep, the firmware actually stops runnig some tasks and the LEDs only update about once per second. To wake from deep sleep there are three ways: (in worst case wake up takes 5ms) *send a charactor to the UART(first charactor will be lost) *toggle CTS low to high and wait 5ms *wake automatically every slot time(*0.625ms) Once the radio is awake it stay active for exactly 1 second of inactivity and then sleeps again. Downside: latency and data loss Disable Output driver Idle or Active (3.1.3) S%,1000 // set all GPIO pins(0-11) to inputs. Lower Transmit Power Idle or Active (3.1.4) SY, // transmit power setting(takes effect after a power cycle and reboot) Downside: reducing effective range Optimizig for Latency --------------------- By default the firmware is optimized for throughput. SQ,16 // set latency bit SQ,0 // unset latency bit Configuration timer settings ---------------------------- Remote configuration is used for the module to be configured with various commands over Bluetooth(SPP profile only?). The module has remote configuration timer to allow remote configuration over Bluetooth after power up in Slave mode. In Master modes the remote configuration timer is set to 0(no remote configuration). (In Trigger Master mode the timer is used as an idle timer to break the connection after time expires with no charactors receive.) ST,0 // no remote, no local when connected ST,<1-252> // local and remote with timeout in seconds from power up ST,253 // local only without timeout ST,254 // remote only without timeout ST,255 // local and remote without timeout Commands -------- S7, 7bit mode SA, Authenticaiton SB, Send break SC, Service class SD, Device class SM, Operation mode SP, Pin code(alpahnumeric) SQ, Special configuration(GPIO, discovery mode, low latency, reboot, UART) SR, Store remote address SR,Z Erase all address SS, Set service name(1-20)** ST, Remote configuration timer(Master:0, Slave:0-255, Triger:as idle timer) SU, UART baud rate SW, low-power sniff mode** deep sleep and wake up every 625us * SX,<0|1> bonding enable only acceps device that matches the stored address SY, power setting** SZ, non-standard raw baud rate =baud*0.004096 S~, Profile 0:SPP, 5:APL, 6:HID S-, Device name -15 alphanumeric charactors S?,<0|1> role switch enable S$, command mode char $|, low-power connect mode deep sleep/active(discoverable and connectable) cycle D display basic setting E display extended setting GB display the device's Bluetooth address GF display Bluetooth address of connected device GK show connection status GR show remote address for reconnecting G& show GPIO pin G show stored setting + toggle local echo on/off & show GPIO 3,4,6,7(DIP switch) C connect to stored remote address C,
connect last address CFI connect and go into fast data mode CFR connect and go into fast data mode CT,
, connect to the address and disconnect after val? F,1 fast data mod: H display help I,