81 Zeilen
2.9 KiB
C
81 Zeilen
2.9 KiB
C
/*
|
|
ChibiOS - (C) 2015-2016 flabbergast <s3+flabbergast@sdfeu.org>
|
|
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
|
you may not use this file except in compliance with the License.
|
|
You may obtain a copy of the License at
|
|
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
Unless required by applicable law or agreed to in writing, software
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
See the License for the specific language governing permissions and
|
|
limitations under the License.
|
|
*/
|
|
|
|
#ifndef _MCUCONF_H_
|
|
#define _MCUCONF_H_
|
|
|
|
#define KL2x_MCUCONF
|
|
|
|
/*
|
|
* HAL driver system settings.
|
|
*/
|
|
#if 1
|
|
/* High-frequency internal RC, 48MHz, possible USB clock recovery */
|
|
#define KINETIS_MCGLITE_MODE KINETIS_MCGLITE_MODE_HIRC
|
|
#define KINETIS_SYSCLK_FREQUENCY 48000000UL
|
|
#define KINETIS_CLKDIV1_OUTDIV1 1
|
|
#endif
|
|
|
|
#if 0
|
|
/* Low-frequency internal RC, 8 MHz mode */
|
|
#define KINETIS_MCGLITE_MODE KINETIS_MCGLITE_MODE_LIRC8M
|
|
#define KINETIS_SYSCLK_FREQUENCY 8000000UL
|
|
#define KINETIS_CLKDIV1_OUTDIV1 1
|
|
#endif
|
|
|
|
/*
|
|
* SERIAL driver system settings.
|
|
*/
|
|
#define KINETIS_SERIAL_USE_UART0 TRUE
|
|
|
|
/*
|
|
* USB driver settings
|
|
*/
|
|
#define KINETIS_USB_USE_USB0 TRUE
|
|
/* need to redefine this, since the default is for K20x */
|
|
#define KINETIS_USB_USB0_IRQ_PRIORITY 2
|
|
|
|
/*
|
|
* Kinetis FOPT configuration byte
|
|
*/
|
|
/* for KL27: */
|
|
#define KINETIS_NV_FOPT_BYTE 0x39
|
|
#define KINETIS_NV_FSEC_BYTE 0x7E
|
|
/* NV_FOPT: bit7-6/BOOTSRC_SEL=0b00 (11=from ROM; 00=from FLASH)
|
|
bit5/FAST_INIT=1, bit4/LPBOOT1=1,
|
|
bit3/RESET_PIN_CFG=1, bit2/NMI_DIS=1,
|
|
bit1/BOOTPIN_OPT=0, bit0/LPBOOT0=1 */
|
|
/* BOOTPIN_OPT: 1=boot depends on BOOTSRC_SEL
|
|
0=boot samples BOOTCFG0=NMI pin */
|
|
/* Boot sequence, page 88 of manual:
|
|
* - If the NMI/BOOTCFG0 input is high or the NMI function is disabled in FTFA_FOPT, the CPU begins execution at the PC location.
|
|
* - If the NMI/BOOTCFG0 input is low, the NMI function is enabled in FTFA_FOPT, and FTFA_FOPT[BOOTPIN_OPT] = 1, this results in an NMI interrupt. The processor executes an Exception Entry and reads the NMI interrupt handler address from vector-table offset 8. The CPU begins execution at the NMI interrupt handler.
|
|
* - When FTFA_FOPT[BOOTPIN_OPT] = 0, it forces boot from ROM if NMI/BOOTCFG0 pin set to 0.
|
|
*
|
|
* Observed behaviour:
|
|
* - when BOOTPIN_OPT=0, BOOTSRC_SEL still matters:
|
|
* - if 0b11 (from ROM), it still boots from ROM, even if BOOTCFG0 pin
|
|
* is high/floating, but leaves ROM and runs user app after
|
|
* 5 seconds delay.
|
|
* - if 0b00 (from FLASH), reset/powerup jumps to user app unless
|
|
* BOOTCFG0 pin is asserted.
|
|
* - in any case, reset when in bootloader induces the 5 second delay
|
|
* before starting the user app.
|
|
*
|
|
*/
|
|
|
|
#endif /* _MCUCONF_H_ */
|