1
0
tmk_keyboard/keyboard/alps64/Makefile
2016-10-12 20:23:02 +09:00

109 行
3.2 KiB
Makefile

# Target file name (without extension).
TARGET ?= alps64
# Directory common source filess exist
TMK_DIR ?= ../../tmk_core
# Directory keyboard dependent files exist
TARGET_DIR ?= .
# project specific files
SRC ?= matrix.c \
led.c
CONFIG_H ?= config.h
# MCU name
MCU ?= atmega32u2
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU ?= 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH ?= AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB ?= $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
BOOTLOADER_SIZE ?= 4096
OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
#SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
#NKRO_ENABLE ?= yes # USB Nkey Rollover
#ACTIONMAP_ENABLE ?= yes # Use 16bit action codes in keymap instead of 8bit keycodes
#
# Keymap file
#
ifeq (yes,$(strip $(UNIMAP_ENABLE)))
KEYMAP_FILE = unimap
else
ifeq (yes,$(strip $(ACTIONMAP_ENABLE)))
KEYMAP_FILE = actionmap
else
KEYMAP_FILE = keymap
endif
endif
ifdef KEYMAP
SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
else
SRC := $(KEYMAP_FILE)_plain.c $(SRC)
endif
# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax
# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TMK_DIR)
include $(TMK_DIR)/protocol/lufa.mk
include $(TMK_DIR)/common.mk
include $(TMK_DIR)/rules.mk