Keyboard firmwares for Atmel AVR and Cortex-M
Você não pode selecionar mais de 25 tópicos Os tópicos devem começar com uma letra ou um número, podem incluir traços ('-') e podem ter até 35 caracteres.

Makefile 4.5KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136
  1. #----------------------------------------------------------------------------
  2. # On command line:
  3. #
  4. # make all = Make software.
  5. #
  6. # make clean = Clean out built project files.
  7. #
  8. # make coff = Convert ELF to AVR COFF.
  9. #
  10. # make extcoff = Convert ELF to AVR Extended COFF.
  11. #
  12. # make program = Download the hex file to the device.
  13. # Please customize your programmer settings(PROGRAM_CMD)
  14. #
  15. # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16. # (must have teensy_loader_cli installed).
  17. #
  18. # make dfu = Download the hex file to the device, using dfu-programmer (must
  19. # have dfu-programmer installed).
  20. #
  21. # make flip = Download the hex file to the device, using Atmel FLIP (must
  22. # have Atmel FLIP installed).
  23. #
  24. # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25. # (must have dfu-programmer installed).
  26. #
  27. # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28. # (must have Atmel FLIP installed).
  29. #
  30. # make debug = Start either simulavr or avarice as specified for debugging,
  31. # with avr-gdb or avr-insight as the front end for debugging.
  32. #
  33. # make filename.s = Just compile filename.c into the assembler code only.
  34. #
  35. # make filename.i = Create a preprocessed source file for use in submitting
  36. # bug reports to the GCC project.
  37. #
  38. # To rebuild project do "make clean" then "make all".
  39. #----------------------------------------------------------------------------
  40. # Target file name (without extension).
  41. TARGET = gherkin
  42. # Directory common source filess exist
  43. TMK_DIR = ../../tmk_core
  44. # Directory keyboard dependent files exist
  45. TARGET_DIR = .
  46. # project specific files
  47. SRC = matrix.c \
  48. led.c \
  49. backlight.c
  50. ifdef KEYMAP
  51. SRC := keymap_$(KEYMAP).c $(SRC)
  52. else
  53. SRC := actionmap_gherkin.c $(SRC)
  54. endif
  55. CONFIG_H = config.h
  56. # MCU name
  57. #MCU = at90usb1287
  58. MCU = atmega32u4
  59. # Processor frequency.
  60. # This will define a symbol, F_CPU, in all source code files equal to the
  61. # processor frequency in Hz. You can then use this symbol in your source code to
  62. # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  63. # automatically to create a 32-bit value in your source code.
  64. #
  65. # This will be an integer division of F_USB below, as it is sourced by
  66. # F_USB after it has run through any CPU prescalers. Note that this value
  67. # does not *change* the processor frequency - it should merely be updated to
  68. # reflect the processor speed set externally so that the code can use accurate
  69. # software delays.
  70. F_CPU = 16000000
  71. #
  72. # LUFA specific
  73. #
  74. # Target architecture (see library "Board Types" documentation).
  75. ARCH = AVR8
  76. # Input clock frequency.
  77. # This will define a symbol, F_USB, in all source code files equal to the
  78. # input clock frequency (before any prescaling is performed) in Hz. This value may
  79. # differ from F_CPU if prescaling is used on the latter, and is required as the
  80. # raw input clock is fed directly to the PLL sections of the AVR for high speed
  81. # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  82. # at the end, this will be done automatically to create a 32-bit value in your
  83. # source code.
  84. #
  85. # If no clock division is performed on the input clock inside the AVR (via the
  86. # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  87. F_USB = $(F_CPU)
  88. # Interrupt driven control endpoint task(+60)
  89. OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  90. # Boot Section Size in *bytes*
  91. # Teensy halfKay 512
  92. # Teensy++ halfKay 1024
  93. # Atmel DFU loader 4096
  94. # LUFA bootloader 4096
  95. # USBaspLoader 2048
  96. OPT_DEFS += -DBOOTLOADER_SIZE=4096
  97. # Build Options
  98. # comment out to disable the options.
  99. #
  100. ACTIONMAP_ENABLE = yes # Use 16bit action codes in keymap instead of 8bit keycodes
  101. BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
  102. MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
  103. EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
  104. CONSOLE_ENABLE = yes # Console for debug(+400)
  105. COMMAND_ENABLE = yes # Commands for debug and configuration
  106. #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
  107. NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
  108. BACKLIGHT_ENABLE = yes
  109. # Optimize size but this may cause error "relocation truncated to fit"
  110. #EXTRALDFLAGS = -Wl,--relax
  111. # Search Path
  112. VPATH += $(TARGET_DIR)
  113. VPATH += $(TMK_DIR)
  114. include $(TMK_DIR)/protocol/lufa.mk
  115. include $(TMK_DIR)/common.mk
  116. include $(TMK_DIR)/rules.mk