124 rivejä
3.8 KiB
Makefile
124 rivejä
3.8 KiB
Makefile
#
|
|
# Makefile for PJRC Teensy
|
|
#
|
|
|
|
|
|
# Target file name (without extension).
|
|
TARGET = x68k_usb
|
|
|
|
# Directory common source filess exist
|
|
TMK_DIR = ../../tmk_core
|
|
|
|
# Directory keyboard dependent files exist
|
|
TARGET_DIR = .
|
|
|
|
# keyboard dependent files
|
|
SRC = keymap.c \
|
|
matrix.c \
|
|
led.c \
|
|
protocol/serial_uart.c
|
|
|
|
CONFIG_H = config.h
|
|
|
|
|
|
# MCU name, you MUST set this to match the board you are using
|
|
# type "make clean" after changing this, so all files will be rebuilt
|
|
#MCU = at90usb162 # Teensy 1.0
|
|
#MCU = atmega32u4 # Teensy 2.0
|
|
#MCU = at90usb646 # Teensy++ 1.0
|
|
#MCU = at90usb1286 # Teensy++ 2.0
|
|
MCU = atmega32u2 # Teensy 2.0
|
|
|
|
|
|
# Processor frequency.
|
|
# Normally the first thing your program should do is set the clock prescaler,
|
|
# so your program will run at the correct speed. You should also set this
|
|
# variable to same clock speed. The _delay_ms() macro uses this, and many
|
|
# examples use this variable to calculate timings. Do not add a "UL" here.
|
|
F_CPU = 16000000
|
|
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH = AVR8
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB = $(F_CPU)
|
|
|
|
# Interrupt driven control endpoint task(+60)
|
|
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
|
|
# Boot Section Size in bytes
|
|
# Teensy halfKay 512
|
|
# Atmel DFU loader 4096
|
|
# LUFA bootloader 4096
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|
|
|
|
|
# Build Options
|
|
# *Comment out* to disable the options.
|
|
#
|
|
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
|
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
|
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
|
CONSOLE_ENABLE = yes # Console for debug(+400)
|
|
COMMAND_ENABLE = yes # Commands for debug and configuration
|
|
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
|
|
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
|
|
|
|
|
|
|
|
#---------------- Programming Options --------------------------
|
|
AVRDUDE = avrdude
|
|
# Type: avrdude -c ? to get a full listing.
|
|
AVRDUDE_PROGRAMMER = avr109
|
|
AVRDUDE_PORT = /dev/ttyACM0
|
|
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
|
|
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
|
|
|
|
# Uncomment the following if you want avrdude's erase cycle counter.
|
|
# Note that this counter needs to be initialized first using -Yn,
|
|
# see avrdude manual.
|
|
#AVRDUDE_ERASE_COUNTER = -y
|
|
|
|
# Uncomment the following if you do /not/ wish a verification to be
|
|
# performed after programming the device.
|
|
#AVRDUDE_NO_VERIFY = -V
|
|
|
|
# Increase verbosity level. Please use this when submitting bug
|
|
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
|
|
# to submit bug reports.
|
|
#AVRDUDE_VERBOSE = -v -v
|
|
|
|
AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
|
|
#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
|
|
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
|
|
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
|
|
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
|
|
|
|
PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
|
|
|
|
|
|
# Search Path
|
|
VPATH += $(TARGET_DIR)
|
|
VPATH += $(TMK_DIR)
|
|
|
|
|
|
include $(TMK_DIR)/protocol.mk
|
|
include $(TMK_DIR)/protocol/lufa.mk
|
|
include $(TMK_DIR)/common.mk
|
|
include $(TMK_DIR)/rules.mk
|