144 lines
4.6 KiB
Makefile
144 lines
4.6 KiB
Makefile
|
#----------------------------------------------------------------------------
|
||
|
|
# On command line:
|
||
|
|
#
|
||
|
|
# make all = Make software.
|
||
|
|
#
|
||
|
|
# make clean = Clean out built project files.
|
||
|
|
#
|
||
|
|
# make coff = Convert ELF to AVR COFF.
|
||
|
|
#
|
||
|
|
# make extcoff = Convert ELF to AVR Extended COFF.
|
||
|
|
#
|
||
|
|
# make program = Download the hex file to the device.
|
||
|
|
# Please customize your programmer settings(PROGRAM_CMD)
|
||
|
|
#
|
||
|
|
# make teensy = Download the hex file to the device, using teensy_loader_cli.
|
||
|
|
# (must have teensy_loader_cli installed).
|
||
|
|
#
|
||
|
|
# make dfu = Download the hex file to the device, using dfu-programmer (must
|
||
|
|
# have dfu-programmer installed).
|
||
|
|
#
|
||
|
|
# make flip = Download the hex file to the device, using Atmel FLIP (must
|
||
|
|
# have Atmel FLIP installed).
|
||
|
|
#
|
||
|
|
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
|
||
|
|
# (must have dfu-programmer installed).
|
||
|
|
#
|
||
|
|
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
|
||
|
|
# (must have Atmel FLIP installed).
|
||
|
|
#
|
||
|
|
# make debug = Start either simulavr or avarice as specified for debugging,
|
||
|
|
# with avr-gdb or avr-insight as the front end for debugging.
|
||
|
|
#
|
||
|
|
# make filename.s = Just compile filename.c into the assembler code only.
|
||
|
|
#
|
||
|
|
# make filename.i = Create a preprocessed source file for use in submitting
|
||
|
|
# bug reports to the GCC project.
|
||
|
|
#
|
||
|
|
# To rebuild project do "make clean" then "make all".
|
||
|
|
#----------------------------------------------------------------------------
|
||
|
|
|
||
|
|
# Target file name (without extension).
|
||
|
|
TARGET = adb_usb_lufa
|
||
|
|
|
||
|
|
# Directory common source filess exist
|
||
|
|
TMK_DIR = ../../tmk_core
|
||
|
|
|
||
|
|
# Directory keyboard dependent files exist
|
||
|
|
TARGET_DIR = .
|
||
|
|
|
||
|
|
# project specific files
|
||
|
|
SRC = keymap_common.c \
|
||
|
|
matrix.c \
|
||
|
|
led.c \
|
||
|
|
adb.c
|
||
|
|
|
||
|
|
ifdef KEYMAP
|
||
|
|
SRC := keymap_$(KEYMAP).c $(SRC)
|
||
|
|
else
|
||
|
|
SRC := keymap_ansi.c $(SRC)
|
||
|
|
endif
|
||
|
|
|
||
|
|
CONFIG_H = config.h
|
||
|
|
|
||
|
|
|
||
|
|
# MCU name
|
||
|
|
# atmega32u4 Teensy2.0
|
||
|
|
# atemga32u4 TMK Converter rev.1
|
||
|
|
# atemga32u2 TMK Converter rev.2
|
||
|
|
MCU = atmega32u4
|
||
|
|
|
||
|
|
# Processor frequency.
|
||
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
||
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
||
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||
|
|
# automatically to create a 32-bit value in your source code.
|
||
|
|
#
|
||
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
||
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
||
|
|
# does not *change* the processor frequency - it should merely be updated to
|
||
|
|
# reflect the processor speed set externally so that the code can use accurate
|
||
|
|
# software delays.
|
||
|
|
F_CPU = 16000000
|
||
|
|
|
||
|
|
|
||
|
|
#
|
||
|
|
# LUFA specific
|
||
|
|
#
|
||
|
|
# Target architecture (see library "Board Types" documentation).
|
||
|
|
ARCH = AVR8
|
||
|
|
|
||
|
|
# Input clock frequency.
|
||
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
||
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
||
|
|
# source code.
|
||
|
|
#
|
||
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
||
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||
|
|
F_USB = $(F_CPU)
|
||
|
|
|
||
|
|
# Interrupt driven control endpoint task(+60)
|
||
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||
|
|
|
||
|
|
|
||
|
|
# Boot Section Size in *bytes*
|
||
|
|
# Teensy halfKay 512
|
||
|
|
# Teensy++ halfKay 1024
|
||
|
|
# Atmel DFU loader 4096 for TMK Converter rev.1/rev.2
|
||
|
|
# LUFA bootloader 4096
|
||
|
|
# USBaspLoader 2048
|
||
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=512
|
||
|
|
|
||
|
|
|
||
|
|
# Build Options
|
||
|
|
# comment out to disable the options.
|
||
|
|
#
|
||
|
|
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
||
|
|
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
||
|
|
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
||
|
|
CONSOLE_ENABLE = yes # Console for debug(+400)
|
||
|
|
COMMAND_ENABLE = yes # Commands for debug and configuration
|
||
|
|
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
|
||
|
|
#NKRO_ENABLE = yes # USB Nkey Rollover
|
||
|
|
ADB_MOUSE_ENABLE = yes
|
||
|
|
|
||
|
|
# ADB Mice need acceleration for todays much bigger screens.
|
||
|
|
OPT_DEFS += -DADB_MOUSE_MAXACC=8
|
||
|
|
|
||
|
|
|
||
|
|
# Optimize size but this may cause error "relocation truncated to fit"
|
||
|
|
#EXTRALDFLAGS = -Wl,--relax
|
||
|
|
|
||
|
|
# Search Path
|
||
|
|
VPATH += $(TARGET_DIR)
|
||
|
|
VPATH += $(TMK_DIR)
|
||
|
|
|
||
|
|
include $(TMK_DIR)/protocol/lufa.mk
|
||
|
|
include $(TMK_DIR)/protocol.mk
|
||
|
|
include $(TMK_DIR)/common.mk
|
||
|
|
include $(TMK_DIR)/rules.mk
|