107 lines
3.4 KiB
Makefile
107 lines
3.4 KiB
Makefile
|
#
|
||
|
|
# Makefile for Teensy
|
||
|
|
#
|
||
|
|
# Target file name (without extension).
|
||
|
|
TARGET = serialmouse_usb
|
||
|
|
|
||
|
|
# Directory common source filess exist
|
||
|
|
TOP_DIR = ../..
|
||
|
|
|
||
|
|
# Directory keyboard dependent files exist
|
||
|
|
TARGET_DIR = .
|
||
|
|
|
||
|
|
# project specific files
|
||
|
|
SRC = keymap.c \
|
||
|
|
matrix.c \
|
||
|
|
led.c
|
||
|
|
|
||
|
|
CONFIG_H = config.h
|
||
|
|
|
||
|
|
|
||
|
|
# MCU name
|
||
|
|
#MCU = at90usb1287
|
||
|
|
MCU = atmega32u4
|
||
|
|
|
||
|
|
# Processor frequency.
|
||
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
||
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
||
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||
|
|
# automatically to create a 32-bit value in your source code.
|
||
|
|
#
|
||
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
||
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
||
|
|
# does not *change* the processor frequency - it should merely be updated to
|
||
|
|
# reflect the processor speed set externally so that the code can use accurate
|
||
|
|
# software delays.
|
||
|
|
F_CPU = 16000000
|
||
|
|
|
||
|
|
|
||
|
|
#
|
||
|
|
# LUFA specific
|
||
|
|
#
|
||
|
|
# Target architecture (see library "Board Types" documentation).
|
||
|
|
ARCH = AVR8
|
||
|
|
|
||
|
|
# Input clock frequency.
|
||
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
||
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
||
|
|
# source code.
|
||
|
|
#
|
||
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
||
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||
|
|
F_USB = $(F_CPU)
|
||
|
|
|
||
|
|
# Interrupt driven control endpoint task(+60)
|
||
|
|
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||
|
|
|
||
|
|
|
||
|
|
# Boot Section Size in *bytes*
|
||
|
|
# Teensy halfKay 512
|
||
|
|
# Teensy++ halfKay 1024
|
||
|
|
# Atmel DFU loader 4096
|
||
|
|
# LUFA bootloader 4096
|
||
|
|
# USBaspLoader 2048
|
||
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=512
|
||
|
|
|
||
|
|
|
||
|
|
# Build Options
|
||
|
|
# comment out to disable the options.
|
||
|
|
#
|
||
|
|
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
||
|
|
#MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
||
|
|
#EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
||
|
|
CONSOLE_ENABLE = yes # Console for debug(+400)
|
||
|
|
#COMMAND_ENABLE = yes # Commands for debug and configuration
|
||
|
|
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
|
||
|
|
|
||
|
|
|
||
|
|
# Serial Mouse Options
|
||
|
|
# You can choose a mouse protocol and the implementation of
|
||
|
|
# the underlying serial connection.
|
||
|
|
#
|
||
|
|
SERIAL_MOUSE_MICROSOFT_ENABLE = yes # Enable support for Microsoft-compatible mice
|
||
|
|
#SERIAL_MOUSE_MOUSESYSTEMS_ENABLE = yes # Enable support for Mousesystems-compatible mice
|
||
|
|
#SERIAL_MOUSE_USE_UART = yes # use hardware UART for serial connection
|
||
|
|
SERIAL_MOUSE_USE_SOFT = yes # use software serial implementation
|
||
|
|
|
||
|
|
# Optional serial mouse driver features
|
||
|
|
# Support scrolling while holding the middle mouse button
|
||
|
|
# (currently only supported for Mousesystems mice):
|
||
|
|
#OPT_DEFS += -DSERIAL_MOUSE_CENTER_SCROLL
|
||
|
|
|
||
|
|
# Optimize size but this may cause error "relocation truncated to fit"
|
||
|
|
#EXTRALDFLAGS = -Wl,--relax
|
||
|
|
|
||
|
|
# Search Path
|
||
|
|
VPATH += $(TARGET_DIR)
|
||
|
|
VPATH += $(TOP_DIR)
|
||
|
|
|
||
|
|
include $(TOP_DIR)/protocol.mk
|
||
|
|
include $(TOP_DIR)/protocol/lufa.mk
|
||
|
|
include $(TOP_DIR)/common.mk
|
||
|
|
include $(TOP_DIR)/rules.mk
|