2011-05-25 01:37:58 +00:00
#
# Makefile for V-USB
#
2011-01-28 15:44:05 +00:00
# Target file name (without extension).
2011-05-25 01:37:58 +00:00
TARGET = ps2_usb_vusb
2011-01-28 15:44:05 +00:00
# Directory common source filess exist
2012-06-07 15:37:46 +00:00
TOP_DIR = ../..
2011-01-28 15:44:05 +00:00
# Directory keyboard dependent files exist
TARGET_DIR = .
# keyboard dependent files
2011-09-17 13:39:50 +00:00
SRC = main.c \
keymap.c \
matrix.c \
led.c \
ps2_usart.c
2011-01-28 15:44:05 +00:00
2011-02-21 06:43:17 +00:00
CONFIG_H = config_vusb.h
2011-05-06 15:04:18 +00:00
# V-USB debug level: To use ps2_usart.c level must be 0
# ps2_usart.c requires USART to receive PS/2 signal.
2011-01-28 15:44:05 +00:00
OPT_DEFS = -DDEBUG_LEVEL= 0
# MCU name, you MUST set this to match the board you are using
# type "make clean" after changing this, so all files will be rebuilt
#MCU = at90usb162 # Teensy 1.0
#MCU = atmega32u4 # Teensy 2.0
#MCU = at90usb646 # Teensy++ 1.0
#MCU = at90usb1286 # Teensy++ 2.0
MCU = atmega168
# Processor frequency.
# Normally the first thing your program should do is set the clock prescaler,
# so your program will run at the correct speed. You should also set this
# variable to same clock speed. The _delay_ms() macro uses this, and many
# examples use this variable to calculate timings. Do not add a "UL" here.
2011-02-20 08:46:02 +00:00
F_CPU = 20000000
2011-01-28 15:44:05 +00:00
# Build Options
# comment out to disable the options.
#
2011-02-08 15:03:58 +00:00
MOUSEKEY_ENABLE = yes # Mouse keys
2011-09-17 13:39:50 +00:00
EXTRAKEY_ENABLE = yes # Audio control and System control
#NKRO_ENABLE = yes # USB Nkey Rollover
NO_UART = yes # UART is unavailable
2011-01-28 15:44:05 +00:00
2011-02-20 08:46:02 +00:00
2011-02-21 06:43:17 +00:00
#---------------- Programming Options --------------------------
AVRDUDE = avrdude
2011-02-20 08:46:02 +00:00
# Type: avrdude -c ? to get a full listing.
AVRDUDE_PROGRAMMER = usbasp
AVRDUDE_PORT =
AVRDUDE_WRITE_FLASH = -U flash:w:$( TARGET) .hex
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
# Uncomment the following if you want avrdude's erase cycle counter.
# Note that this counter needs to be initialized first using -Yn,
# see avrdude manual.
#AVRDUDE_ERASE_COUNTER = -y
# Uncomment the following if you do /not/ wish a verification to be
# performed after programming the device.
#AVRDUDE_NO_VERIFY = -V
# Increase verbosity level. Please use this when submitting bug
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
# to submit bug reports.
#AVRDUDE_VERBOSE = -v -v
#AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS = -p $( MCU) -c $( AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS += $( AVRDUDE_NO_VERIFY)
AVRDUDE_FLAGS += $( AVRDUDE_VERBOSE)
AVRDUDE_FLAGS += $( AVRDUDE_ERASE_COUNTER)
2011-02-21 06:43:17 +00:00
PROGRAM_CMD = $( AVRDUDE) $( AVRDUDE_FLAGS) $( AVRDUDE_WRITE_FLASH) $( AVRDUDE_WRITE_EEPROM)
2011-02-20 08:46:02 +00:00
2012-06-07 03:35:24 +00:00
i n c l u d e $( TOP_DIR ) / p r o t o c o l / v u s b . m k
i n c l u d e $( TOP_DIR ) / p r o t o c o l . m k
i n c l u d e $( TOP_DIR ) / c o m m o n . m k
i n c l u d e $( TOP_DIR ) / r u l e s . m k