1
0
This repo is archived. You can view files and clone it, but cannot push or open issues or pull requests.
tmk_keyboard_custom/converter/x68k_usb/Makefile

124 lines
3.8 KiB
Makefile
Raw Normal View History

2012-03-23 16:43:37 +00:00
#
# Makefile for PJRC Teensy
#
# Target file name (without extension).
TARGET = x68k_usb
2012-03-23 16:43:37 +00:00
# Directory common source filess exist
2015-04-09 16:53:24 +00:00
TMK_DIR = ../../tmk_core
2012-03-23 16:43:37 +00:00
# Directory keyboard dependent files exist
TARGET_DIR = .
# keyboard dependent files
2012-06-30 05:44:59 +00:00
SRC = keymap.c \
2012-03-23 16:43:37 +00:00
matrix.c \
led.c \
protocol/serial_uart.c
2012-03-23 16:43:37 +00:00
CONFIG_H = config.h
2012-03-23 16:43:37 +00:00
# MCU name, you MUST set this to match the board you are using
# type "make clean" after changing this, so all files will be rebuilt
#MCU = at90usb162 # Teensy 1.0
#MCU = atmega32u4 # Teensy 2.0
2012-03-23 16:43:37 +00:00
#MCU = at90usb646 # Teensy++ 1.0
#MCU = at90usb1286 # Teensy++ 2.0
MCU = atmega32u2 # Teensy 2.0
2012-03-23 16:43:37 +00:00
# Processor frequency.
# Normally the first thing your program should do is set the clock prescaler,
# so your program will run at the correct speed. You should also set this
# variable to same clock speed. The _delay_ms() macro uses this, and many
# examples use this variable to calculate timings. Do not add a "UL" here.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
2013-06-21 07:34:39 +00:00
# Boot Section Size in bytes
# Teensy halfKay 512
# Atmel DFU loader 4096
# LUFA bootloader 4096
OPT_DEFS += -DBOOTLOADER_SIZE=4096
2012-03-23 16:43:37 +00:00
# Build Options
# *Comment out* to disable the options.
#
2013-06-21 07:34:39 +00:00
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
2012-03-23 16:43:37 +00:00
#---------------- Programming Options --------------------------
AVRDUDE = avrdude
# Type: avrdude -c ? to get a full listing.
AVRDUDE_PROGRAMMER = avr109
AVRDUDE_PORT = /dev/ttyACM0
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
# Uncomment the following if you want avrdude's erase cycle counter.
# Note that this counter needs to be initialized first using -Yn,
# see avrdude manual.
#AVRDUDE_ERASE_COUNTER = -y
# Uncomment the following if you do /not/ wish a verification to be
# performed after programming the device.
#AVRDUDE_NO_VERIFY = -V
# Increase verbosity level. Please use this when submitting bug
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
# to submit bug reports.
#AVRDUDE_VERBOSE = -v -v
AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
2012-03-23 16:43:37 +00:00
2012-06-30 05:44:59 +00:00
# Search Path
VPATH += $(TARGET_DIR)
2015-04-09 07:20:42 +00:00
VPATH += $(TMK_DIR)
2012-06-30 05:44:59 +00:00
2012-03-23 16:43:37 +00:00
2015-04-09 07:20:42 +00:00
include $(TMK_DIR)/protocol.mk
include $(TMK_DIR)/protocol/lufa.mk
2015-04-09 07:20:42 +00:00
include $(TMK_DIR)/common.mk
include $(TMK_DIR)/rules.mk