|
1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950515253545556575859606162636465666768697071727374757677787980818283848586878889909192939495969798 |
- #
- # Makefile for TMK keyboard converter rev2
- # https://github.com/tmk/keyboard_converter#pcb-rev2
- #
- # Target file name (without extension).
- TARGET = ps2_usb_tmk_rev2
-
- # Directory common source filess exist
- TMK_DIR = ../../tmk_core
-
- # Directory keyboard dependent files exist
- TARGET_DIR = .
-
- # project specific files
- SRC = keymap_common.c \
- matrix.c \
- led.c
-
- ifdef KEYMAP
- SRC := keymap_$(KEYMAP).c $(SRC)
- else
- SRC := keymap_plain.c $(SRC)
- endif
-
- CONFIG_H = config_tmk_rev2.h
-
-
- # MCU name
- MCU = atmega32u2
-
- # Processor frequency.
- # This will define a symbol, F_CPU, in all source code files equal to the
- # processor frequency in Hz. You can then use this symbol in your source code to
- # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
- # automatically to create a 32-bit value in your source code.
- #
- # This will be an integer division of F_USB below, as it is sourced by
- # F_USB after it has run through any CPU prescalers. Note that this value
- # does not *change* the processor frequency - it should merely be updated to
- # reflect the processor speed set externally so that the code can use accurate
- # software delays.
- F_CPU = 16000000
-
-
- #
- # LUFA specific
- #
- # Target architecture (see library "Board Types" documentation).
- ARCH = AVR8
-
- # Input clock frequency.
- # This will define a symbol, F_USB, in all source code files equal to the
- # input clock frequency (before any prescaling is performed) in Hz. This value may
- # differ from F_CPU if prescaling is used on the latter, and is required as the
- # raw input clock is fed directly to the PLL sections of the AVR for high speed
- # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
- # at the end, this will be done automatically to create a 32-bit value in your
- # source code.
- #
- # If no clock division is performed on the input clock inside the AVR (via the
- # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
- F_USB = $(F_CPU)
-
-
- # Boot Section Size in *bytes*
- # Teensy halfKay 512
- # Teensy++ halfKay 1024
- # Atmel DFU loader 4096
- # LUFA bootloader 4096
- # USBaspLoader 2048
- OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
- # Build Options
- # comment out to disable the options.
- #
- #BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
- MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
- EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
- CONSOLE_ENABLE = yes # Console for debug(+400)
- COMMAND_ENABLE = yes # Commands for debug and configuration
- #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
-
-
- # PS/2 Options
- #
- PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
- #PS2_USE_BUSYWAIT = yes # uses primitive reference code
-
-
- # Search Path
- VPATH += $(TARGET_DIR)
- VPATH += $(TMK_DIR)
-
- include $(TMK_DIR)/protocol.mk
- include $(TMK_DIR)/protocol/lufa.mk
- include $(TMK_DIR)/common.mk
- include $(TMK_DIR)/rules.mk
|