@@ -20,6 +20,7 @@ CONFIG_H = config.h | |||
MCU = atmega32u4 # Teensy 2.0 | |||
#MCU = at90usb646 # Teensy++ 1.0 | |||
#MCU = at90usb1286 # Teensy++ 2.0 | |||
#MCU = atmega32u2 # TMK converter | |||
# Processor frequency. | |||
@@ -30,6 +31,29 @@ MCU = atmega32u4 # Teensy 2.0 | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task(+60) | |||
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
@@ -58,6 +82,6 @@ VPATH += $(TOP_DIR) | |||
include $(TOP_DIR)/protocol.mk | |||
include $(TOP_DIR)/protocol/pjrc.mk | |||
include $(TOP_DIR)/protocol/lufa.mk | |||
include $(TOP_DIR)/common.mk | |||
include $(TOP_DIR)/rules.mk |
@@ -0,0 +1,63 @@ | |||
# Target file name (without extension). | |||
TARGET = next_usb | |||
# Directory common source filess exist | |||
TOP_DIR = ../.. | |||
# Directory keyboard dependent files exist | |||
TARGET_DIR = . | |||
# keyboard dependent files | |||
SRC = keymap.c \ | |||
matrix.c \ | |||
led.c | |||
CONFIG_H = config.h | |||
# MCU name, you MUST set this to match the board you are using | |||
# type "make clean" after changing this, so all files will be rebuilt | |||
#MCU = at90usb162 # Teensy 1.0 | |||
MCU = atmega32u4 # Teensy 2.0 | |||
#MCU = at90usb646 # Teensy++ 1.0 | |||
#MCU = at90usb1286 # Teensy++ 2.0 | |||
# Processor frequency. | |||
# Normally the first thing your program should do is set the clock prescaler, | |||
# so your program will run at the correct speed. You should also set this | |||
# variable to same clock speed. The _delay_ms() macro uses this, and many | |||
# examples use this variable to calculate timings. Do not add a "UL" here. | |||
F_CPU = 16000000 | |||
# Boot Section Size in *bytes* | |||
# Teensy halfKay 512 | |||
# Teensy++ halfKay 1024 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
# USBaspLoader 2048 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# *Comment out* to disable the options. | |||
# | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys | |||
EXTRAKEY_ENABLE = yes # Audio control and System control | |||
CONSOLE_ENABLE = yes # Console for debug(+400) | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
#NKRO_ENABLE = yes # USB Nkey Rollover | |||
SRC += next_kbd.c | |||
# Search Path | |||
VPATH += $(TARGET_DIR) | |||
VPATH += $(TOP_DIR) | |||
include $(TOP_DIR)/protocol.mk | |||
include $(TOP_DIR)/protocol/pjrc.mk | |||
include $(TOP_DIR)/common.mk | |||
include $(TOP_DIR)/rules.mk |
@@ -60,6 +60,7 @@ POSSIBILITY OF SUCH DAMAGE. | |||
//#define TEENSY_CONFIG 1 | |||
#define PRO_MICRO_CONFIG 1 | |||
//#define TMK_CONFIG 1 | |||
// comment out if you don't want the keyboard's LEDs to flash upon initialization | |||
#define NEXT_KBD_INIT_FLASH_LEDS | |||
@@ -143,6 +144,43 @@ POSSIBILITY OF SUCH DAMAGE. | |||
#endif | |||
//================= End of Teensy 2.0 Configuration ================== | |||
//================ Start of TMK converter Configuration ================= | |||
#ifdef TMK_CONFIG | |||
// this is the debugging LED that flashes when a key is being pressed | |||
// comment out in order to disable debugging LED | |||
#define NEXT_KBD_LED1_PORT PORTD | |||
#define NEXT_KBD_LED1_PIN PIND | |||
#define NEXT_KBD_LED1_DDR DDRD | |||
#define NEXT_KBD_LED1_BIT 6 | |||
#define NEXT_KBD_LED1_ON NEXT_KBD_LED1_PORT |= (1<<NEXT_KBD_LED1_BIT); | |||
#define NEXT_KBD_LED1_OFF NEXT_KBD_LED1_PORT &= ~(1<<NEXT_KBD_LED1_BIT); | |||
// corresponds to the Keyboard In wire on the NeXT connector | |||
#define NEXT_KBD_OUT_PORT PORTD | |||
#define NEXT_KBD_OUT_PIN PIND | |||
#define NEXT_KBD_OUT_DDR DDRD | |||
#define NEXT_KBD_OUT_BIT 1 | |||
// corresponds to the Keyboard Out wire on the NeXT connector | |||
#define NEXT_KBD_IN_PORT PORTD | |||
#define NEXT_KBD_IN_PIN PIND | |||
#define NEXT_KBD_IN_DDR DDRD | |||
#define NEXT_KBD_IN_BIT 0 | |||
// this pin is an input for the power key on the NeXT keyboard | |||
// as the keyboard is powered on this should be normally high; | |||
// if it is pulled low it means the power button is being preseed | |||
#define NEXT_KBD_PWR_PORT PORTD | |||
#define NEXT_KBD_PWR_PIN PIND | |||
#define NEXT_KBD_PWR_DDR DDRD | |||
#define NEXT_KBD_PWR_BIT 4 | |||
#endif | |||
//================= End of TMK converter Configuration ================== | |||
/* key combination for command */ | |||
#define IS_COMMAND() ( \ | |||
(keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))|| \ |