Update doc
This commit is contained in:
tmk
parent
1f96edaed6
commit
60096e11c7
@ -1,12 +1,37 @@
|
||||
Roving RN-42
|
||||
============
|
||||
|
||||
TODO
|
||||
----
|
||||
Bug:
|
||||
- with Nexus5 keyboard and mouse are very laggy.
|
||||
|
||||
- lose USB connection during power-down mode
|
||||
- USB initialize code in main() causes this - WRONG
|
||||
- Do not power-down during USB connection is active - DONE 11/11
|
||||
(USB_DeviceState == USB_DEVICE_Configured) is used to check USB connection
|
||||
matrix_power_down() matrix.c - 11/23
|
||||
|
||||
Todo:
|
||||
|
||||
Design:
|
||||
- remove MCU dependent power saving code from core/keyboard
|
||||
- it should be located in project matrix.c - DONE 11/23
|
||||
- HHKB matrix.c needs matrix_prev?
|
||||
- is_modified() is obsolete now. really needs?
|
||||
|
||||
|
||||
LUFA:
|
||||
USB connection check: state of USB deivce
|
||||
- USB_DeviceState:
|
||||
USB_Deivce_State_t { Unattached, Powered, Default, Addressed, Configured*, Suspended* }
|
||||
- USB_IsInitialized: state of LUFA core setup
|
||||
becomes true in USB_Init() USBController_AVR8.c
|
||||
becomes false in USB_Disable() USBController_AVR8.c
|
||||
- USB_VBUS_GetStatus(): state of VBUS(power/connection)
|
||||
- USB_Disable() detaches, disables all interrupts, controller, PLL, regulater.
|
||||
|
||||
|
||||
Power saving:
|
||||
- confirm suspend mode lufa.c: matrix_power_*, suspend_wakeup_condition
|
||||
- 8MHz clock
|
||||
- When not connected in a few minutes get into deep sleep to save battery life
|
||||
- CTS is needed for waking up from deep sleep? How deep sleep is activated?
|
||||
@ -19,6 +44,9 @@ Power saving:
|
||||
- high resistor 100K/1M?
|
||||
capacitor 10nF
|
||||
http://www.eevblog.com/forum/beginners/measuring-battery-voltage-without-consuming-current/
|
||||
- During USB suspend change clock source to internal RC from external Xtal(6.8)
|
||||
- FRZCLK: you can freeze clock for power saving. still WAKEUPI and VBUSTI interrupts are available while freezing.(21.7.3)
|
||||
- Suspend: Clear Suspend Bit, Freeze clock, disable PLL, MCU sleep(21.13)
|
||||
|
||||
Improving:
|
||||
- BT LED; connecting, linked, sleeping, deep sleeping
|
||||
@ -306,6 +334,10 @@ SM,5 Auto Connect ANY Mode (Mode =ANY)
|
||||
SM,6 automatically reconnect(Mode =Pair)
|
||||
confirm: auto connect works well but difficult to enter command mode.
|
||||
|
||||
SR,Z removes all remote addresses for reconnecting.
|
||||
can be used to connect another host
|
||||
SR,I registers last inquiry address
|
||||
|
||||
|
||||
Fast data mode
|
||||
--------------
|
||||
|
||||
102
keyboard/hhkb_rn42/PowerSave.txt
Normal file
102
keyboard/hhkb_rn42/PowerSave.txt
Normal file
@ -0,0 +1,102 @@
|
||||
RN-42
|
||||
=====
|
||||
|
||||
HHKB key switch power control
|
||||
-----------------------------
|
||||
MOS FET Nch: BSS138 or IRLML6344T, either works and no apparent difference.
|
||||
Normally on(pull-up) or off(pull-down)? interms of power saving it prefers pull-down?
|
||||
|
||||
Pull-down will be better for power saving, normally off.
|
||||
|
||||
|
||||
|
||||
Used Timer
|
||||
----------
|
||||
|
||||
8MHz clock
|
||||
----------
|
||||
1) 16MHz xtal with system prescaler div2: F_CPU=8MHz, F_USB=16MHz
|
||||
2) 8MHz xtal with div1: F_CPU=8MHz, F_USB=8MHz
|
||||
Hardware USART doesn't work at 115200bps with 8MHz(F_CPU).
|
||||
|
||||
workaround:
|
||||
a) use Sotwre serial for communcation with RN-42
|
||||
b) reduce baud of RN-42 to lower rate;(factory default is 115200bps)
|
||||
10/03
|
||||
|
||||
|
||||
|
||||
Slave mode
|
||||
----------
|
||||
Discovery/Inquire
|
||||
Connect/Page
|
||||
|
||||
SI,0012
|
||||
SJ,0012
|
||||
InqWindw=0100
|
||||
PagWindw=0100
|
||||
|
||||
|
||||
Sniff mode
|
||||
----------
|
||||
0.625ms * <hex>
|
||||
SW,0320 Very sluggish. Type is not lost but very slow to register.
|
||||
SW,0160 Still sluggish. may transposed? can type but ...
|
||||
Mouse point move intermittently
|
||||
SW,0020 feel a bit late like stumble(20ms)
|
||||
SW,0010 feel no latency(10ms)
|
||||
|
||||
|
||||
Deep sleep
|
||||
----------
|
||||
SW,8010
|
||||
|
||||
|
||||
TX power
|
||||
--------
|
||||
SY,fff4
|
||||
|
||||
|
||||
IO pins
|
||||
-------
|
||||
S%,1000 status led and connection control don't work
|
||||
GPIO5: status LED
|
||||
GPIO6: Connection control
|
||||
GPIO2: linked status
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
Ver 6.15 04/26/2013
|
||||
(c) Roving Networks
|
||||
***Settings***
|
||||
BTA=00066667BBE9
|
||||
BTName=tmkBT-BBE9
|
||||
Baudrt(SW4)=115K
|
||||
Mode =DTR
|
||||
Authen=1
|
||||
Bonded=0
|
||||
Rem=001BDC06415B
|
||||
***ADVANCED Settings***
|
||||
SrvName= keyboard/mouse
|
||||
SrvClass=0000
|
||||
DevClass=1F00
|
||||
InqWindw=0012
|
||||
PagWindw=0012
|
||||
CfgTimer=255
|
||||
StatuStr=NULL
|
||||
HidFlags=3c
|
||||
DTRtimer=8
|
||||
KeySwapr=0
|
||||
***OTHER Settings***
|
||||
Profile= HID
|
||||
CfgChar= $
|
||||
SniffEna=8010
|
||||
LowPower=0 S|,
|
||||
TX Power=fff4 SY,
|
||||
IOPorts= 0
|
||||
IOValues=0
|
||||
Sleeptmr=0
|
||||
DebugMod=0
|
||||
RoleSwch=0
|
||||
Reference in New Issue
Block a user