- Makefile use LUFA now - Change MCU ports PF{0,1} to PD{0,1} - Add build option for keymap to Makefile: make keymap=hasuled_matrix
@@ -1,5 +1,5 @@ | |||
# Target file name (without extension). | |||
TARGET = m0110 | |||
TARGET = m0110_lufa | |||
# Directory common source filess exist | |||
TOP_DIR = ../.. | |||
@@ -8,11 +8,17 @@ TOP_DIR = ../.. | |||
TARGET_DIR = . | |||
# keyboard dependent files | |||
SRC = keymap.c \ | |||
matrix.c \ | |||
SRC = matrix.c \ | |||
led.c \ | |||
m0110.c | |||
# To use own keymap file run make like: make keymap=hasu | |||
ifdef keymap | |||
SRC += keymap_$(keymap).c | |||
else | |||
SRC += keymap.c | |||
endif | |||
CONFIG_H = config.h | |||
@@ -32,6 +38,29 @@ MCU = atmega32u4 # Teensy 2.0 | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in bytes | |||
# Teensy halfKay 512 | |||
# Atmel DFU loader 4096 | |||
@@ -61,7 +90,7 @@ VPATH += $(TARGET_DIR) | |||
VPATH += $(TOP_DIR) | |||
include $(TOP_DIR)/protocol/pjrc.mk | |||
include $(TOP_DIR)/protocol/lufa.mk | |||
include $(TOP_DIR)/protocol.mk | |||
include $(TOP_DIR)/common.mk | |||
include $(TOP_DIR)/rules.mk |
@@ -1,90 +0,0 @@ | |||
# Target file name (without extension). | |||
TARGET = m0110_lufa | |||
# Directory common source filess exist | |||
TOP_DIR = ../.. | |||
# Directory keyboard dependent files exist | |||
TARGET_DIR = . | |||
# keyboard dependent files | |||
SRC = keymap.c \ | |||
matrix.c \ | |||
led.c \ | |||
m0110.c | |||
CONFIG_H = config.h | |||
# MCU name, you MUST set this to match the board you are using | |||
# type "make clean" after changing this, so all files will be rebuilt | |||
#MCU = at90usb162 # Teensy 1.0 | |||
MCU = atmega32u4 # Teensy 2.0 | |||
#MCU = at90usb646 # Teensy++ 1.0 | |||
#MCU = at90usb1286 # Teensy++ 2.0 | |||
# Processor frequency. | |||
# Normally the first thing your program should do is set the clock prescaler, | |||
# so your program will run at the correct speed. You should also set this | |||
# variable to same clock speed. The _delay_ms() macro uses this, and many | |||
# examples use this variable to calculate timings. Do not add a "UL" here. | |||
F_CPU = 16000000 | |||
# | |||
# LUFA specific | |||
# | |||
# Target architecture (see library "Board Types" documentation). | |||
ARCH = AVR8 | |||
# Input clock frequency. | |||
# This will define a symbol, F_USB, in all source code files equal to the | |||
# input clock frequency (before any prescaling is performed) in Hz. This value may | |||
# differ from F_CPU if prescaling is used on the latter, and is required as the | |||
# raw input clock is fed directly to the PLL sections of the AVR for high speed | |||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' | |||
# at the end, this will be done automatically to create a 32-bit value in your | |||
# source code. | |||
# | |||
# If no clock division is performed on the input clock inside the AVR (via the | |||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. | |||
F_USB = $(F_CPU) | |||
# Interrupt driven control endpoint task | |||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT | |||
# Boot Section Size in bytes | |||
# Teensy halfKay 512 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# comment out to disable the options. | |||
# | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = yes # Console for debug(+400) | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend | |||
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |||
#---------------- Programming Options -------------------------- | |||
PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex | |||
# Search Path | |||
VPATH += $(TARGET_DIR) | |||
VPATH += $(TOP_DIR) | |||
include $(TOP_DIR)/protocol/lufa.mk | |||
include $(TOP_DIR)/protocol.mk | |||
include $(TOP_DIR)/common.mk | |||
include $(TOP_DIR)/rules.mk |
@@ -1,5 +1,5 @@ | |||
# Target file name (without extension). | |||
TARGET = m0110 | |||
TARGET = m0110_pjrc | |||
# Directory common source filess exist | |||
TOP_DIR = ../.. | |||
@@ -8,11 +8,17 @@ TOP_DIR = ../.. | |||
TARGET_DIR = . | |||
# keyboard dependent files | |||
SRC = keymap_hasu.c \ | |||
matrix.c \ | |||
SRC = matrix.c \ | |||
led.c \ | |||
m0110.c | |||
# To use own keymap file run make like: make keymap=hasu | |||
ifdef keymap | |||
SRC += keymap_$(keymap).c | |||
else | |||
SRC += keymap.c | |||
endif | |||
CONFIG_H = config.h | |||
@@ -32,13 +38,23 @@ MCU = atmega32u4 # Teensy 2.0 | |||
F_CPU = 16000000 | |||
# Boot Section Size in bytes | |||
# Teensy halfKay 512 | |||
# Atmel DFU loader 4096 | |||
# LUFA bootloader 4096 | |||
OPT_DEFS += -DBOOTLOADER_SIZE=4096 | |||
# Build Options | |||
# *Comment out* to disable the options. | |||
# | |||
MOUSEKEY_ENABLE = yes # Mouse keys | |||
#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support | |||
EXTRAKEY_ENABLE = yes # Audio control and System control | |||
#NKRO_ENABLE = yes # USB Nkey Rollover | |||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) | |||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700) | |||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450) | |||
CONSOLE_ENABLE = yes # Console for debug(+400) | |||
COMMAND_ENABLE = yes # Commands for debug and configuration | |||
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend | |||
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA | |||
@@ -11,10 +11,16 @@ you can use other board with USB AVR like `ATmega32U4` and `AT90USB`. | |||
Update | |||
------ | |||
- 2013/08 Change port for signals PF to PD | |||
Connection | |||
---------- | |||
You need 4P4C plug and cable to connect Teensy or other AVR dev board into the keyboard. | |||
Teensy port `PF0` is assigned for `CLOCK` line and `PF1` for `DATA` by default, | |||
Teensy port `PD0` is assigned for `CLOCK` line and `PD1` for `DATA` by default, | |||
you can change pin configuration with editing *config.h*. | |||
You can find 4P4C plugs on telephone handset cable. Note that it is *crossover* connection | |||
@@ -53,8 +59,8 @@ You can edit *Makefile* and *config.h* to change compile options and pin configu | |||
$ git clone git://github.com/tmk/tmk_keyboard.git (or download source) | |||
$ cd m0110_usb | |||
$ make -f Makefile.lufa clean | |||
$ make -f Makefile.lufa | |||
$ make -f Makefile clean | |||
$ make -f Makefile | |||
and program your Teensy with [PJRC Teensy loader](http://www.pjrc.com/teensy/loader.html). | |||
@@ -21,7 +21,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
#define VENDOR_ID 0xFEED | |||
#define PRODUCT_ID 0x0110 | |||
#define DEVICE_VER 0x0100 | |||
#define DEVICE_VER 0x0101 | |||
#define MANUFACTURER t.m.k. | |||
#define PRODUCT M0110 keyboard converter | |||
#define DESCRIPTION convert M0110 keyboard to USB | |||
@@ -50,13 +50,13 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
/* ports */ | |||
#define M0110_CLOCK_PORT PORTF | |||
#define M0110_CLOCK_PIN PINF | |||
#define M0110_CLOCK_DDR DDRF | |||
#define M0110_CLOCK_PORT PORTD | |||
#define M0110_CLOCK_PIN PIND | |||
#define M0110_CLOCK_DDR DDRD | |||
#define M0110_CLOCK_BIT 0 | |||
#define M0110_DATA_PORT PORTF | |||
#define M0110_DATA_PIN PINF | |||
#define M0110_DATA_DDR DDRF | |||
#define M0110_DATA_PORT PORTD | |||
#define M0110_DATA_PIN PIND | |||
#define M0110_DATA_DDR DDRD | |||
#define M0110_DATA_BIT 1 | |||
#endif |
@@ -19,7 +19,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
#include <stdint.h> | |||
#include <stdbool.h> | |||
#include <avr/pgmspace.h> | |||
#include "usb_keyboard.h" | |||
#include "keycode.h" | |||
#include "print.h" | |||
#include "debug.h" | |||
@@ -153,7 +152,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
* `-----------------------------------------------' `---------------' | |||
*/ | |||
KEYMAP( | |||
GRV, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, NLCK,EQL, PSLS,PAST, | |||
ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSPC, NLCK,EQL, PSLS,PAST, | |||
TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, P7, P8, P9, PMNS, | |||
LCTL,A, S, D, F, G, H, J, K, L, FN1, QUOT, FN0, P4, P5, P6, PPLS, | |||
LSFT,Z, X, C, V, B, N, M, COMM,DOT, FN2, FN3, P1, P2, P3, PENT, | |||
@@ -161,7 +160,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
), | |||
// HHKB & WASD | |||
KEYMAP( | |||
ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST, | |||
GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST, | |||
CAPS,NO, NO, NO, NO, NO, NO, NO, PSCR,SLCK,PAUS,UP, NO, P7, P8, P9, PMNS, | |||
LCTL,VOLD,VOLU,MUTE,NO, NO, NO, NO, HOME,PGUP,LEFT,RGHT, FN0, P4, P5, P6, PPLS, | |||
LSFT,NO, NO, NO, NO, NO, NO, NO, END, PGDN,DOWN, FN3, P1, P2, P3, PENT, | |||
@@ -169,7 +168,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
), | |||
// vi mousekeys | |||
KEYMAP( | |||
ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST, | |||
GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST, | |||
CAPS,NO, NO, NO, NO, NO, WH_L,WH_D,WH_U,WH_R,PSCR,SLCK,PAUS, P7, P8, P9, PMNS, | |||
LCTL,VOLD,VOLU,MUTE,NO, NO, MS_L,MS_D,MS_U,MS_R,FN1, NO, ENT, P4, P5, P6, PPLS, | |||
LSFT,NO, NO, NO, NO, BTN3,BTN2,BTN1,NO, NO, NO, NO, P1, P2, P3, PENT, | |||
@@ -177,7 +176,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { | |||
), | |||
// vi cusorkeys | |||
KEYMAP( | |||
ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST, | |||
GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, NLCK,EQL, PSLS,PAST, | |||
CAPS,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, PSCR,SLCK,PAUS, P7, P8, P9, PMNS, | |||
LCTL,NO, NO, NO, NO, NO, LEFT,DOWN,UP, RGHT,NO, NO, ENT, P4, P5, P6, PPLS, | |||
LSFT,NO, NO, NO, NO, NO, HOME,PGDN,PGUP,END, FN2, NO, P1, P2, P3, PENT, |