You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
This repo is archived. You can view files and clone it, but cannot push or open issues/pull-requests.

Makefile 4.6KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141
  1. #----------------------------------------------------------------------------
  2. # On command line:
  3. #
  4. # make all = Make software.
  5. #
  6. # make clean = Clean out built project files.
  7. #
  8. # make coff = Convert ELF to AVR COFF.
  9. #
  10. # make extcoff = Convert ELF to AVR Extended COFF.
  11. #
  12. # make program = Download the hex file to the device.
  13. # Please customize your programmer settings(PROGRAM_CMD)
  14. #
  15. # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16. # (must have teensy_loader_cli installed).
  17. #
  18. # make dfu = Download the hex file to the device, using dfu-programmer (must
  19. # have dfu-programmer installed).
  20. #
  21. # make flip = Download the hex file to the device, using Atmel FLIP (must
  22. # have Atmel FLIP installed).
  23. #
  24. # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25. # (must have dfu-programmer installed).
  26. #
  27. # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28. # (must have Atmel FLIP installed).
  29. #
  30. # make debug = Start either simulavr or avarice as specified for debugging,
  31. # with avr-gdb or avr-insight as the front end for debugging.
  32. #
  33. # make filename.s = Just compile filename.c into the assembler code only.
  34. #
  35. # make filename.i = Create a preprocessed source file for use in submitting
  36. # bug reports to the GCC project.
  37. #
  38. # To rebuild project do "make clean" then "make all".
  39. #----------------------------------------------------------------------------
  40. # Target file name (without extension).
  41. TARGET = alps64
  42. # Directory common source filess exist
  43. TMK_DIR = ../../tmk_core
  44. # Directory keyboard dependent files exist
  45. TARGET_DIR = .
  46. # project specific files
  47. SRC = matrix.c \
  48. led.c
  49. CONFIG_H = config.h
  50. # MCU name
  51. MCU = atmega32u2
  52. # Processor frequency.
  53. # This will define a symbol, F_CPU, in all source code files equal to the
  54. # processor frequency in Hz. You can then use this symbol in your source code to
  55. # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  56. # automatically to create a 32-bit value in your source code.
  57. #
  58. # This will be an integer division of F_USB below, as it is sourced by
  59. # F_USB after it has run through any CPU prescalers. Note that this value
  60. # does not *change* the processor frequency - it should merely be updated to
  61. # reflect the processor speed set externally so that the code can use accurate
  62. # software delays.
  63. F_CPU = 16000000
  64. #
  65. # LUFA specific
  66. #
  67. # Target architecture (see library "Board Types" documentation).
  68. ARCH = AVR8
  69. # Input clock frequency.
  70. # This will define a symbol, F_USB, in all source code files equal to the
  71. # input clock frequency (before any prescaling is performed) in Hz. This value may
  72. # differ from F_CPU if prescaling is used on the latter, and is required as the
  73. # raw input clock is fed directly to the PLL sections of the AVR for high speed
  74. # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  75. # at the end, this will be done automatically to create a 32-bit value in your
  76. # source code.
  77. #
  78. # If no clock division is performed on the input clock inside the AVR (via the
  79. # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  80. F_USB = $(F_CPU)
  81. # Interrupt driven control endpoint task(+60)
  82. OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  83. # Boot Section Size in *bytes*
  84. # Teensy halfKay 512
  85. # Teensy++ halfKay 1024
  86. # Atmel DFU loader 4096
  87. # LUFA bootloader 4096
  88. # USBaspLoader 2048
  89. OPT_DEFS += -DBOOTLOADER_SIZE=4096
  90. # Build Options
  91. # comment out to disable the options.
  92. #
  93. BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
  94. MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
  95. EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
  96. CONSOLE_ENABLE = yes # Console for debug(+400)
  97. COMMAND_ENABLE = yes # Commands for debug and configuration
  98. #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
  99. #NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
  100. #ACTIONMAP_ENABLE = yes # Use 16bit action codes in keymap instead of 8bit keycodes
  101. ifdef ACTIONMAP_ENABLE
  102. KEYMAP_FILE = actionmap
  103. else
  104. KEYMAP_FILE = keymap
  105. SRC := keymap_common.c $(SRC)
  106. endif
  107. ifdef KEYMAP
  108. SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
  109. else
  110. SRC := $(KEYMAP_FILE)_plain.c $(SRC)
  111. endif
  112. # Optimize size but this may cause error "relocation truncated to fit"
  113. #EXTRALDFLAGS = -Wl,--relax
  114. # Search Path
  115. VPATH += $(TARGET_DIR)
  116. VPATH += $(TMK_DIR)
  117. include $(TMK_DIR)/protocol/lufa.mk
  118. include $(TMK_DIR)/common.mk
  119. include $(TMK_DIR)/rules.mk