Архівний
1
0
This repo is archived. You can view files and clone it, but cannot push or open issues or pull requests.
tmk_keyboard_custom/converter/sun_usb/config.h
John Hickey d3332d32da Add hardware serial support for sun_usb converter
Tested with a Sun Type 5c keyboard and a 7404 inverter.
2016-05-09 22:56:33 -07:00

127 рядки
4.7 KiB
C

/*
Copyright 2012 Jun Wako <wakojun@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef CONFIG_H
#define CONFIG_H
#define VENDOR_ID 0xFEED
#define PRODUCT_ID 0x3333
#define DEVICE_VER 0x0100
#define MANUFACTURER t.m.k.
#define PRODUCT Sun keyboard converter
#define DESCRIPTION converts Sun keyboard protocol into USB
/* matrix size */
#define MATRIX_ROWS 16
#define MATRIX_COLS 8
/* key combination for command */
#define IS_COMMAND() ( \
keyboard_report->mods == (MOD_BIT(KC_LALT) | MOD_BIT(KC_RALT)) || \
keyboard_report->mods == (MOD_BIT(KC_LGUI) | MOD_BIT(KC_RGUI)) || \
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
)
/* legacy keymap support */
#define USE_LEGACY_KEYMAP
/* HARDWARE_SERAIL assumes that a logic inverter (7404) is placed
* in front of RX/TX to produce the positive logic the MCU expects.
* The default is Software Serial.
*/
#if defined(HARDWARE_SERIAL)
/* Hardware Serial (USART) configuration
* asynchronous, negative logic, 1200baud, no flow control
* 1-start bit, 8-data bit, non parity, 1-stop bit
*
*/
#if defined(__AVR_ATmega32U4__) || defined(__AVR_ATmega32U2__)
#define SERIAL_UART_BAUD 1200
#define SERIAL_UART_DATA UDR1
#define SERIAL_UART_UBRR ((F_CPU/(16UL*SERIAL_UART_BAUD))-1)
#define SERIAL_UART_RXD_VECT USART1_RX_vect
#define SERIAL_UART_TXD_READY (UCSR1A&(1<<UDRE1))
#define SERIAL_UART_INIT() do { \
UBRR1L = (uint8_t) SERIAL_UART_UBRR; /* baud rate */ \
UBRR1H = (uint8_t) (SERIAL_UART_UBRR>>8); /* baud rate */ \
UCSR1B = (1<<RXCIE1) | (1<<RXEN1) | /* RX: interrupt, RX: enable */ \
(1<<TXEN1); /* TX: enable */ \
UCSR1C = (0<<UPM11) | (0<<UPM10) | /* parity: none(00), even(01), odd(11) */ \
(0<<UCSZ12) | (1<<UCSZ11) | (1<<UCSZ10); /* data-8bit(011) */ \
sei(); \
} while(0)
#else
# error "USART configuration is needed."
#endif
#else
/* Software Serial configuration
* asynchronous, negative logic, 1200baud, no flow control
* 1-start bit, 8-data bit, non parity, 1-stop bit
*/
#define SERIAL_SOFT_BAUD 1200
#define SERIAL_SOFT_PARITY_NONE
#define SERIAL_SOFT_BIT_ORDER_LSB
#define SERIAL_SOFT_LOGIC_NEGATIVE
/* RXD Port */
#define SERIAL_SOFT_RXD_ENABLE
#define SERIAL_SOFT_RXD_DDR DDRD
#define SERIAL_SOFT_RXD_PORT PORTD
#define SERIAL_SOFT_RXD_PIN PIND
#define SERIAL_SOFT_RXD_BIT 2
#define SERIAL_SOFT_RXD_VECT INT2_vect
/* RXD Interupt */
#ifdef SERIAL_SOFT_LOGIC_NEGATIVE
/* enable interrupt: INT2(rising edge) */
#define INTR_TRIG_EDGE ((1<<ISC21)|(1<<ISC20))
#else
/* enable interrupt: INT2(falling edge) */
#define INTR_TRIG_EDGE ((1<<ISC21)|(0<<ISC20))
#endif
#define SERIAL_SOFT_RXD_INIT() do { \
/* pin configuration: input with pull-up */ \
SERIAL_SOFT_RXD_DDR &= ~(1<<SERIAL_SOFT_RXD_BIT); \
SERIAL_SOFT_RXD_PORT |= (1<<SERIAL_SOFT_RXD_BIT); \
EICRA |= INTR_TRIG_EDGE; \
EIMSK |= (1<<INT2); \
sei(); \
} while (0)
#define SERIAL_SOFT_RXD_INT_ENTER()
#define SERIAL_SOFT_RXD_INT_EXIT() do { \
/* clear interrupt flag */ \
EIFR = (1<<INTF2); \
} while (0)
#define SERIAL_SOFT_RXD_READ() (SERIAL_SOFT_RXD_PIN&(1<<SERIAL_SOFT_RXD_BIT))
/* TXD Port */
#define SERIAL_SOFT_TXD_ENABLE
#define SERIAL_SOFT_TXD_DDR DDRD
#define SERIAL_SOFT_TXD_PORT PORTD
#define SERIAL_SOFT_TXD_PIN PIND
#define SERIAL_SOFT_TXD_BIT 3
#define SERIAL_SOFT_TXD_HI() do { SERIAL_SOFT_TXD_PORT |= (1<<SERIAL_SOFT_TXD_BIT); } while (0)
#define SERIAL_SOFT_TXD_LO() do { SERIAL_SOFT_TXD_PORT &= ~(1<<SERIAL_SOFT_TXD_BIT); } while (0)
#define SERIAL_SOFT_TXD_INIT() do { \
/* pin configuration: output */ \
SERIAL_SOFT_TXD_DDR |= (1<<SERIAL_SOFT_TXD_BIT); \
/* idle */ \
SERIAL_SOFT_TXD_ON(); \
} while (0)
#endif //hardware serial
#endif //config.h