USB - General
- Refactored descriptors
- Enabled/Disable USB endpoints
- Added debug flags for special features
- Code cleanup
- Interface count calculation based off of enabled endpoints
- Delayed wTotalLength calculation to simplify descriptor offsets
- Re-ordered endpoints and interfaces
- Added more debug output
- Added usbInitTime to show how long keyboard initialization took
  (Useful when debugging bad init sequences)
- Added function for usb_resume() which takes care of the resume sequence
  * Resume is now only called if packets are starting to timeout

USB - Special Options
- Added enableDeviceRestartOnUSBTimeout
  * A last resort hammer for bad USB Chipsets/OSs, don't use if you can help it
  * Disabled
- Added enableUSBResume
  * Enables host resume wake-up signalling, required to wake a computer from sleep
  * Enabled
- Added enableUSBLowPowerNegotiation
  * Enables power negotiation hack
  * Required to use firmware with an IPad and other hard-limit low-power USB hosts
  * Hasn't been tested with the recent changes
  * Disabled
- Added enableUSBSuspend
  * Enables power down events on host USB bus suspend
  * Enabled

USB - Keyboard
- Attempted to cleanup HID SET_REPORT
  * Works much better
  * Still has an issue under Linux which generates *a lot* of NAKs (initializes quickly regardless)
    + Not present on other keyboards
    + SETUP -> OUT -> IN : This sequence is the problem
    + Specifically during the OUT phase
- Enabled

USB - CDC Virtual Serial Port
- Code cleanup
- Added convenience struct USBCDCLineCoding for easier debugging
- Attempted to cleanup CDC_SET_LING_CODING
  * Works much better
  * Still has an issue under Linux which generates *a lot* of NAKs (initializes quickly regardless)
    + SETUP -> OUT -> IN : This sequence is the problem
    + Specifically during the OUT phase
    + Likely the same issues as HID SET_REPORT
- Enabled

USB - Mouse
- Enabled

USB - Joystick
- Disabled

USB - RawIO
- Initial code, API not used yet
- Disabled

DFU
- Updated load script, now faster

- Somewhat aggresive, may cause restarts if the keyboard/OS hasn't fully intialized the keyboard
- Added GET_IDLE handling and correct usage of SET_IDLE
- Initial implementation of idle send, commented out as it causes issues on Mac OSX for sleeping
  (keyboard has been working without it)
- MacOSX seems to have some sort of data corruption on the USB link, not sure why (other OSs have no issues)
- Cleaned up some code
- Added a longer sleep after the resume sequence to prevent possible issues sending keys too soon
  (may need to be increased more)

Ipad support now seems flaky, though Mac, Windows seems solid.
Init sequence on Linux seems slow, even though there are no errors.

- Maintains a sleep state variable (may be able to use as a signal in the future)
- On the first keypress, hold the RESUME signal for 10 ms (spec says between 1 and 15 ms)
- Removed some messages that were affecting sleep state

- Still very basic (lots of room for improvement)
- Capability format will likely change at some point
- 16 bit movement control, however repeat rate limits usability (will need KLL 0.4 to make better)

- Full Mouse support will have to wait for KLL 0.6
  * This will include dynamic HID descriptor generation for many wheels and axis depending on the KLL needs
- HID descriptor is currently limited to 8 buttons
- Technically mouse movement also works (tested by accident), but it's disable for now (needs some API thought)

- Adding additional udev rules
- Added KRO mode default define

- Each scan module now has a current change callback which passes the available current as a parameter
- No longer attempts to use the max 500 mA immediately, starts with 100 mA then goes to 500 mA after enumeration
- If enumeration fails due to bMaxPower of 500 mA, then attempt again at 100 mA (might also be possible to go even lower to 20 mA in certain cases)
- Now working with the Apple Ipad (no over-power messages)
- Fixed Wake-up behaviour on Apple Ipad (and likely other iOS devices)
- More effecient set_feature/clear_feature handling (device handler)
- Initial power handling via Interconnect (still needs work to get it more dynamic)

- Now enabled by default
- Added protection around remote jumps

- Adds proper flashMode support for all keyboards and microcontrollers (usb and serial)
- flashModeEnabled must be set to 1 otherwise it will only show an error
  * This is on purpose (somewhat dangerous feature as it allows remote flashing)
- Capability cleanup

- Fixed cli reflash mode set
- Cleaned up debugging code
- 4 500 000 baud seems to be reliable
- Fixed master selection (assumes slave node unless USB enumerates)

- Required for 0.3b update of the KLL compiler.

Forgot to pull some files. Fixed those up too.

Use a consistent standard - Tabs in front for indenting, spaces after for anything else. This way everything stays nice and lined up while also letting users change there prefered indent level. Most of the new files from Haata where already in this format.

fixes #15

- Displays all of the bytes sent via USB
- Different display mode for NKRO and Boot modes

- Currently actual detection commented out due to issues

- Not ready yet
- Will require some more changes to Lib/mk20dx.c

- Modifier byte was being cleared after each send (needed for Boot Mode only)

- Fixed descriptor to not include USB Code 156 (Clear)
- This USB Code affects repeating Delete

- Tested both with Boot and NKRO modes

- It's possible to get even more, but this is probably as far as I'll go
- PROGMEM is really annoying to use, and makes the code look like ass
- Now the Teensy 2++ should have enough RAM to use PartialMap easily

- Thanks hasu for pointing it out
- Keycode 50 is problematic under Linux, so removing (it's a duplicate keycode anyways)

- When changing the mode, a key buffer flush is required (might confuse the OS temporarily)

- Setting NKRO mode as default (up to bios to disable)

- API changes from the AVR NKRO support

- NKRO for USB Codes 4 to 164, 176 to 221 and modifiers
- Added System Control support codes 129 to 183
- Added Consumer Control support codes 32 to 668

- Only send USB events when something changes (rather than every ms)

- Still working on USB NKRO

- Layers were not disabling because function was only called on press/hold
- Disabled layer shift function on key hold
- Fixed the press/hold/release states for other layer capabilities and USB code send

- CLI now works with hex or decimal numbers
- Hex requires 0x (technically just x would work too)

- Changed static variables to const that should have been const
- Updated CMake files to prepare for MCHCK custom bootloader
- Changed the USB ID numbers and ID number for bootloader
- Only generate DFU or Teensy binary image, not both
- Fixed RAM and FLASH calculator
- Added missing license in delay.c/h (much of it was taken from Teensy source though I've changed a bunch of it)
- Prepared mk20dx.c for upcoming bootloader addition
- mk20dx.h cleanup
- Reduced the MCHCK based flash size for the application image (bootloader changes requires more flash space)
- Fixed bugs in macro.c
- Added keyHold cli command
- Added show pending events debug message for PartialMap macro module

- Macros and Layers are, code-wise, feature complete

- Cleaned up Macro and USB callback naming
- Added security jumper for automated reload (MCHCK based only)
- Added additional LED position

- Requires special string to be compared with the bootloader and VBAT register file

- McHCK uses FLL instead of the PLL for USB (startup, not usb init)
- Added optional debug for the pjrc USB module
- Cleaned up compiler flags

- Refactored pjrc USB (definitions to the .h file)

- Mostly for reference, you shouldn't include it verbatim in your module.

- Code should be working, but much is untested
- All of the old modules will need to update and use the new DefaultMap keymap
- There might still be some naming conflicts with some Scan Modules

- Functions themselves are working
- LED functionality has never actually worked, still doesn't :P
- Should be easy to test NKRO USB now

- Includes serial putchar and getchar cleanup (overall)
- Moved avr-capsense to DPH (renaming)
- Basic cleanup for including CLI on the avr architecture

- reset   -> Simulates power cycle (Not yet compatible with AVR)
- reload  -> Sets the device into firmware reload mode
- led     -> Toggles the error LED
- version -> Displays detailed version information (additions to CMake files was necessary, might have broken Windows builds...)

* Initial cli code