reverse SS HIGH/LOW in Scanner_ShiftRegsPISOMultiRow::scan()
This commit is contained in:
parent
3fa0aee2e2
commit
d9465be221
@ -142,6 +142,7 @@ The following is a listing of items to check when a new keybrd sketch or keyboar
|
||||
|
||||
Development-environment items to check:
|
||||
* If the keyboard has an I/O expander, power cycle (replug the USB) after loading the HEX file.
|
||||
* Sometimes sketch will not loading properly if two instances of Arduino IDE are open.
|
||||
* For compile error:
|
||||
```
|
||||
'KEY_A' was not declared in this scope
|
||||
|
@ -21,32 +21,44 @@ Initializes shift register's shift/load pin.
|
||||
*/
|
||||
void Scanner_ShiftRegsPISOMultiRow::begin()
|
||||
{
|
||||
digitalWrite(slaveSelect, HIGH); //initialize ??only needed for first scan
|
||||
SPI.begin(); //todo move this to constructor or init()
|
||||
}
|
||||
|
||||
/* scan() strobes the row's strobePin and returns state of the shift register's input pins.
|
||||
strobePin is Arduino pin number connected to this row.
|
||||
Bit patterns are 1 bit per key.
|
||||
|
||||
Scanner_ShiftRegsPISOMultiRow class was tested on two sets of 74HC165 shift registers
|
||||
and 74AHC1G126 tri-state buffer chips
|
||||
|
||||
74HC165 is not an SPI device.
|
||||
The 74HC165 SH/LD polarity is the inverse of SPI slave-select convention.
|
||||
Most SPI chips will high-Z their MISO pin when their slave select signal is high.
|
||||
To use SPI-like protocol, 74HC*126 will high-Z the MISO pin when the slave select signal is low.
|
||||
|
||||
SPI.beginTransaction() and SPI.endTransaction() are not needed,
|
||||
but would be needed if trackball uses interrupts.
|
||||
*/
|
||||
read_pins_t Scanner_ShiftRegsPISOMultiRow::scan(const uint8_t strobePin)
|
||||
{
|
||||
read_pins_t readState = 0; //bits, 1 means key is pressed, 0 means released
|
||||
|
||||
SPI.beginTransaction( SPISettings(5000000, MSBFIRST, SPI_MODE0) ); //control SPI bus, 5 MHz
|
||||
|
||||
digitalWrite(slaveSelect, LOW); //load parallel inputs to registers
|
||||
|
||||
digitalWrite(strobePin, strobeOn); //strobe on
|
||||
|
||||
delayMicroseconds(3); //time to stabilize photo-transistor todo need?
|
||||
delayMicroseconds(50); //todo for sr2_LEDs_strobe.ino
|
||||
digitalWrite(slaveSelect, HIGH); //shift the data toward a serial output
|
||||
//SPI.beginTransaction( SPISettings(5000000, MSBFIRST, SPI_MODE0) ); //control SPI bus, 5 MHz
|
||||
|
||||
delayMicroseconds(20); //photo-transistor at 3.3v needs 20 ms to stablize
|
||||
|
||||
digitalWrite(slaveSelect, HIGH); //shift the data toward a serial output
|
||||
|
||||
digitalWrite(strobePin, strobeOff); //strobe off
|
||||
|
||||
SPI.transfer(&readState, byte_count);
|
||||
|
||||
SPI.endTransaction();
|
||||
//SPI.endTransaction();
|
||||
|
||||
digitalWrite(slaveSelect, LOW); //load parallel inputs to registers
|
||||
|
||||
return readState;
|
||||
}
|
||||
|
@ -36,9 +36,9 @@ read_pins_t Scanner_ShiftRegsPISOSingleRow::scan(const uint8_t strobePin)
|
||||
read_pins_t readState = 0; //bits, 1 means key is pressed, 0 means released
|
||||
|
||||
//read all the column pins
|
||||
digitalWrite(slaveSelect, LOW); //load parallel inputs to the register
|
||||
digitalWrite(slaveSelect, HIGH); //shift the data toward a serial output
|
||||
SPI.transfer(&readState, byte_count);
|
||||
digitalWrite(slaveSelect, LOW); //load parallel inputs to the register
|
||||
|
||||
return readState;
|
||||
}
|
||||
|
Reference in New Issue
Block a user