- M0110/M0110A to USB keyboard converter
- ======================================
- This firmware converts the protocol of Apple Macintosh keyboard **M0110**, **M0110A** and **M0120** into USB. Target of this project is USB AVR controller **ATmega32U4**. Using this converter you can revive these retro keyboards with modern computer.
-
- Pictures of **M0110 + M0120** and **M0110A**.
-
- ![M0110+M0120](http://i.imgur.com/dyvXb2Tm.jpg)
- ![M0110A](http://i.imgur.com/HuHOEoHm.jpg)
-
-
- - M0110A support was contributed by [skagon@github](https://github.com/skagon).
- - M0120 also is supported. keys(+ * / and ,) on M0120 are recognized as cursor keys.
-
-
-
- Update
- ------
- - 2013/08: Change port for signals `PF` to `PD`
- - 2013/09: Change port again, it uses inversely `PD0` for data and `PD1` for clock line now.
-
-
-
- Building Hardware
- -----------------
- You need **4P4C** cable and **ATMega32U4** board like PJRC [Teensy]. Port of the MCU `PD1` is assigned to `CLOCK` line and `PD0` to `DATA` by default, you can change pin configuration with editing `config.h`.
-
- [![M0110 Converter](http://i.imgur.com/4G2ZOegm.jpg)](http://i.imgur.com/4G2ZOeg.jpg)
-
- ### 4P4C phone handset cable
- Note that original cable used with Mac is **straight** while phone handset cable is **crossover**.
-
- <http://en.wikipedia.org/wiki/Modular_connector#4P4C>
-
- Close-up picture of handset cable. You can see one end of plug has reverse color codes against the other. Click to enlarge.
- [![4P4C cable](http://i.imgur.com/3S9P1mYm.jpg?1)](http://i.imgur.com/3S9P1mY.jpg?1)
-
- [Teensy]: http://www.pjrc.com/teensy/
-
-
- ### Socket Pinout
- - <http://pinouts.ru/Inputs/MacKeyboard_pinout.shtml>
-
- ![Jack fig](http://www.kbdbabel.org/conn/kbd_connector_macplus.png)
-
-
- ### Pull-up Resistor
- You may need pull-up resistors on signal lines(`CLOCK`, `DATA`) in particular when you have long or coiled cable. **1k-10k Ohm** will be OK for this purpose. In that case the converter may not read signal from keyboard correctly without pull-up resistors.
-
-
-
- Building Firmware
- -----------------
- To compile firmware you need AVR GCC. You can edit *Makefile* and *config.h* to change compile options and pin configuration.
-
- $ git clone git://github.com/tmk/tmk_keyboard.git (or download source)
- $ cd m0110_usb
- $ make -f Makefile clean
- $ make -f Makefile
-
- and program your Teensy with [PJRC Teensy loader](http://www.pjrc.com/teensy/loader.html).
-
-
-
- Keymap
- ------
- You can change keymaps by editing *keymap.c*.
-
- ### M0110 & M0120
- #### *Default Layer*
- ,---------------------------------------------------------. ,---------------.
- | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Clr| -|Lft|Rgt|
- |---------------------------------------------------------| |---------------|
- |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \| | 7| 8| 9| Up|
- |---------------------------------------------------------| |---------------|
- |Caps | A| S| D| F| G| H| J| K| L| ;| '|Enter | | 4| 5| 6| Dn|
- |---------------------------------------------------------| |---------------|
- |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shift | | 1| 2| 3| |
- `---------------------------------------------------------' |-----------|Ent|
- |Ctl|Gui | Space |Alt |Ctl| | 0| .| |
- `-----------------------------------------------' `---------------'
-
- - `Space` and `Enter` also work as `Fn` layer switch key when holding down.
-
- #### *Function Layer(WASD/HHKB)*
- ,---------------------------------------------------------. ,---------------.
- |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| |Nlk| -|Lft|Rgt|
- |---------------------------------------------------------| |---------------|
- |Caps |Hom| Up|PgU| | | | |Psc|Slk|Pau|Up |Ins| \| | 7| 8| 9| Up|
- |---------------------------------------------------------| |---------------|
- |Caps |Lef|Dow|Rig| | | | |Hom|PgU|Lef|Rig|Enter | | 4| 5| 6| Dn|
- |---------------------------------------------------------| |---------------|
- |Shift |End| |PgD| | | | |End|PgD|Dow|Shift | | 1| 2| 3| |
- `---------------------------------------------------------' |-----------|Ent|
- |Ctl|Gui | Space |Alt |Ctl| | 0| .| |
- `-----------------------------------------------' `---------------'
-
-
- ### M0110A
- #### *Default Layer*
- ,---------------------------------------------------------. ,---------------.
- | `| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backs| |Clr| =| /| *|
- |---------------------------------------------------------| |---------------|
- |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| | | 7| 8| 9| -|
- |-----------------------------------------------------' | |---------------|
- |Caps | A| S| D| F| G| H| J| K| L| ;| '|Enter | | 4| 5| 6| +|
- |---------------------------------------------------------| |---------------|
- |Shift | Z| X| C| V| B| N| M| ,| ,| /|Shft| Up| | 1| 2| 3| |
- |---------------------------------------------------------| |-----------|Ent|
- |Ctrl |Gui | Space | \|Lft|Rgt|Dwn| | 0| .| |
- `---------------------------------------------------------' `---------------'
-
- - `Space` and `Enter` also work as `Fn` layer switch key when holding down.
- - `Backslash(\)` also works as `Alt` when holding down.
-
- #### *Function Layer(WASD/HHKB)*
- ,---------------------------------------------------------. ,---------------.
- |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Delet| |Nlk| =| /| *|
- |---------------------------------------------------------| |---------------|
- |Caps |Hom| Up|PgU| | | | |Psc|Slk|Pau|Up |Ins| | | 7| 8| 9| -|
- |-----------------------------------------------------' | |---------------|
- |Caps |Lef|Dow|Rig| | | | |Hom|PgU|Lef|Rig|Enter | | 4| 5| 6| +|
- |---------------------------------------------------------| |---------------|
- |Shift |End| |PgD| | | | |End|PgD|Dow|Shif|PgU| | 1| 2| 3| |
- |---------------------------------------------------------| |-----------|Ent|
- |Ctrl |Gui | Space | \|Hom|End|PgD| | 0| .| |
- `---------------------------------------------------------' `---------------'
-
-
-
- Debug
- -----
- You can use [PJRC HID listen](http://www.pjrc.com/teensy/hid_listen.html) to see debug output. The converter has some functions for debug, press `<Command>+H` simultaneously to get help.
-
- - Command: `Shift+Option+Command`(`Shift+Alt+Gui` or `Shift+Alt+Control`)
|