1
0
tmk_keyboard/converter/ps2_usb/Makefile

106 lines
3.1 KiB
Makefile
Raw Normal View History

2014-04-29 10:42:24 +00:00
#
# Makefile for Teensy
#
2011-01-17 12:51:51 +00:00
# Target file name (without extension).
TARGET = ps2_usb_lufa
2011-01-17 12:51:51 +00:00
# Directory common source filess exist
2015-04-09 16:53:24 +00:00
TMK_DIR = ../../tmk_core
2011-01-17 12:51:51 +00:00
# Directory keyboard dependent files exist
TARGET_DIR = .
# project specific files
SRC = keymap_common.c \
matrix.c \
led.c
ifdef KEYMAP
SRC := keymap_$(KEYMAP).c $(SRC)
else
SRC := keymap_plain.c $(SRC)
endif
CONFIG_H = config.h
2011-01-17 12:51:51 +00:00
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
2011-01-17 12:51:51 +00:00
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
2011-01-17 12:51:51 +00:00
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
2011-01-17 12:51:51 +00:00
# Interrupt driven control endpoint task(+60)
2014-04-29 10:42:24 +00:00
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
2012-10-14 11:03:26 +00:00
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
2014-04-29 10:42:24 +00:00
OPT_DEFS += -DBOOTLOADER_SIZE=512
2012-10-14 11:03:26 +00:00
# Build Options
# comment out to disable the options.
#
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
2012-10-14 11:03:26 +00:00
2011-01-17 12:51:51 +00:00
# PS/2 Options
#
2015-05-18 04:58:56 +00:00
#PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
2013-12-02 03:04:50 +00:00
#PS2_USE_BUSYWAIT = yes # uses primitive reference code
2011-02-21 06:43:17 +00:00
# Optimize size but this may cause error "relocation truncated to fit"
#EXTRALDFLAGS = -Wl,--relax
2011-02-21 06:43:17 +00:00
2012-06-30 05:44:59 +00:00
# Search Path
VPATH += $(TARGET_DIR)
2015-04-09 07:20:42 +00:00
VPATH += $(TMK_DIR)
2012-06-30 05:44:59 +00:00
2015-04-09 07:20:42 +00:00
include $(TMK_DIR)/protocol.mk
include $(TMK_DIR)/protocol/lufa.mk
include $(TMK_DIR)/common.mk
include $(TMK_DIR)/rules.mk