@@ -8,6 +8,7 @@ Keyboard initialization process takes a few seconds at start up. During that you | |||
Update | |||
------ | |||
2015/05/05 Added keymaps for 107-key, 77-key and 50-key. Thanks, orihalcon @ geekhack! | |||
2015/05/19 Fixed a protocol handling bug. | |||
@@ -53,7 +53,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. | |||
/* Pin interrupt on rising edge of clock */ | |||
#define IBM4704_INT_INIT() do { EICRA |= ((1<<ISC11)|(1<<ISC10)); } while (0) | |||
#define IBM4704_INT_ON() do { EIMSK |= (1<<INT1); } while (0) | |||
#define IBM4704_INT_ON() do { EIFR |= (1<<INTF1); EIMSK |= (1<<INT1); } while (0) | |||
#define IBM4704_INT_OFF() do { EIMSK &= ~(1<<INT1); } while (0) | |||
#define IBM4704_INT_VECT INT1_vect | |||
@@ -166,13 +166,14 @@ Data sent from host: | |||
| `-----`--- scan code | |||
`------------- enable bit(0: enable repeat, 1: enable break) | |||
00-77 Enable repeat(78-7F: invalid scancode) | |||
80-F7 Enable break(F8-FF: invalid scancode) | |||
00-79 Enable repeat | |||
80-F9 Enable break(FA-FF are used as other commands, see above.) | |||
FE Resend(011ah) no need to use | |||
FF End(0114h) exits FC command mode. | |||
Response from keyboard: | |||
FD Out of bound - Invalid scancode | |||
-- OK - No response means that command is accepted. | |||
Examples: | |||
To enable break code of all keys. |
@@ -67,35 +67,31 @@ uint8_t matrix_cols(void) | |||
static void enable_break(void) | |||
{ | |||
uint8_t ret; | |||
print("Enable break: "); | |||
// valid scancode: 00-79h | |||
for (uint8_t code = 0; code < 0x7A; code++) { | |||
while (ibm4704_send(0x80|code)) _delay_ms(1); | |||
// get none when ok, get FD when out of bound | |||
_delay_ms(5); | |||
if ((ret = ibm4704_recv()) != 0xff) { | |||
xprintf("c%02X:r%02X ", code, ret); | |||
} | |||
_delay_ms(1); | |||
while (ibm4704_send(0x80|code)) _delay_ms(10); | |||
_delay_ms(5); // wait for response | |||
// No response(FF) when ok, FD when out of bound | |||
xprintf("s%02X:r%02X ", code, ibm4704_recv()); | |||
} | |||
_delay_us(1000); | |||
while (ibm4704_send(0xFF)) { _delay_ms(1); } // End | |||
while (ibm4704_send(0xFF)) { _delay_ms(10); } // End | |||
print("End\n"); | |||
} | |||
void matrix_init(void) | |||
{ | |||
debug_enable = true; | |||
void matrix_setup(void) | |||
{ | |||
ibm4704_init(); | |||
matrix_clear(); | |||
} | |||
_delay_ms(2000); // wait for starting up debug console | |||
void matrix_init(void) | |||
{ | |||
debug_enable = true; | |||
print("IBM 4704 converter\n"); | |||
while (ibm4704_send(0xFE)) _delay_ms(1); // resend | |||
_delay_ms(5); | |||
matrix_clear(); | |||
_delay_ms(2000); // wait for keyboard starting up | |||
xprintf("Keyboard ID: %02X\n", ibm4704_recv()); | |||
enable_break(); | |||
} |
@@ -21,9 +21,10 @@ uint8_t ibm4704_error = 0; | |||
void ibm4704_init(void) | |||
{ | |||
inhibit(); // keep keyboard from sending | |||
IBM4704_INT_INIT(); | |||
IBM4704_INT_ON(); | |||
idle(); | |||
idle(); // allow keyboard sending | |||
} | |||
/* | |||
@@ -132,8 +133,8 @@ Stop bit: Keyboard pulls down Data line to lo after 9th clock. | |||
ISR(IBM4704_INT_VECT) | |||
{ | |||
static enum { | |||
STOP, BIT0, BIT1, BIT2, BIT3, BIT4, BIT5, BIT6, BIT7, PARITY | |||
} state = STOP; | |||
BIT0, BIT1, BIT2, BIT3, BIT4, BIT5, BIT6, BIT7, PARITY, STOP | |||
} state = BIT0; | |||
// LSB first | |||
static uint8_t data = 0; | |||
// Odd parity | |||
@@ -141,11 +142,7 @@ ISR(IBM4704_INT_VECT) | |||
ibm4704_error = 0; | |||
switch (state++) { | |||
case STOP: | |||
// Data:Low | |||
WAIT(data_lo, 10, state); | |||
break; | |||
switch (state) { | |||
case BIT0: | |||
case BIT1: | |||
case BIT2: | |||
@@ -166,6 +163,10 @@ ISR(IBM4704_INT_VECT) | |||
} | |||
if (!parity) | |||
goto ERROR; | |||
break; | |||
case STOP: | |||
// Data:Low | |||
WAIT(data_lo, 100, state); | |||
rbuf_enqueue(data); | |||
ibm4704_error = IBM4704_ERR_NONE; | |||
goto DONE; | |||
@@ -173,13 +174,14 @@ ISR(IBM4704_INT_VECT) | |||
default: | |||
goto ERROR; | |||
} | |||
state++; | |||
goto RETURN; | |||
ERROR: | |||
ibm4704_error = state; | |||
while (ibm4704_send(0xFE)) _delay_ms(1); // resend | |||
xprintf("R:%02X%02X\n", state, data); | |||
DONE: | |||
state = STOP; | |||
state = BIT0; | |||
data = 0; | |||
parity = false; | |||
RETURN: |