You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
This repo is archived. You can view files and clone it, but cannot push or open issues/pull-requests.

Makefile 4.9KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160
  1. #----------------------------------------------------------------------------
  2. # On command line:
  3. #
  4. # make all = Make software.
  5. #
  6. # make clean = Clean out built project files.
  7. #
  8. # make coff = Convert ELF to AVR COFF.
  9. #
  10. # make extcoff = Convert ELF to AVR Extended COFF.
  11. #
  12. # make program = Download the hex file to the device.
  13. # Please customize your programmer settings(PROGRAM_CMD)
  14. #
  15. # make teensy = Download the hex file to the device, using teensy_loader_cli.
  16. # (must have teensy_loader_cli installed).
  17. #
  18. # make dfu = Download the hex file to the device, using dfu-programmer (must
  19. # have dfu-programmer installed).
  20. #
  21. # make flip = Download the hex file to the device, using Atmel FLIP (must
  22. # have Atmel FLIP installed).
  23. #
  24. # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  25. # (must have dfu-programmer installed).
  26. #
  27. # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  28. # (must have Atmel FLIP installed).
  29. #
  30. # make debug = Start either simulavr or avarice as specified for debugging,
  31. # with avr-gdb or avr-insight as the front end for debugging.
  32. #
  33. # make filename.s = Just compile filename.c into the assembler code only.
  34. #
  35. # make filename.i = Create a preprocessed source file for use in submitting
  36. # bug reports to the GCC project.
  37. #
  38. # To rebuild project do "make clean" then "make all".
  39. #----------------------------------------------------------------------------
  40. # Target file name (without extension).
  41. TARGET = hhkb_lufa
  42. # Directory common source filess exist
  43. TMK_DIR = ../../tmk_core
  44. # Directory keyboard dependent files exist
  45. TARGET_DIR = .
  46. # List C source files here. (C dependencies are automatically generated.)
  47. SRC += keymap_common.c \
  48. matrix.c \
  49. led.c
  50. CONFIG_H = config.h
  51. # MCU name
  52. # PJRC Teensy++ 2.0
  53. #MCU = at90usb1286
  54. # TMK Alt Controller or PJRC Teensy 2.0
  55. MCU = atmega32u4
  56. # Processor frequency.
  57. # This will define a symbol, F_CPU, in all source code files equal to the
  58. # processor frequency in Hz. You can then use this symbol in your source code to
  59. # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  60. # automatically to create a 32-bit value in your source code.
  61. #
  62. # This will be an integer division of F_USB below, as it is sourced by
  63. # F_USB after it has run through any CPU prescalers. Note that this value
  64. # does not *change* the processor frequency - it should merely be updated to
  65. # reflect the processor speed set externally so that the code can use accurate
  66. # software delays.
  67. F_CPU = 16000000
  68. #
  69. # LUFA specific
  70. #
  71. # Target architecture (see library "Board Types" documentation).
  72. ARCH = AVR8
  73. # Input clock frequency.
  74. # This will define a symbol, F_USB, in all source code files equal to the
  75. # input clock frequency (before any prescaling is performed) in Hz. This value may
  76. # differ from F_CPU if prescaling is used on the latter, and is required as the
  77. # raw input clock is fed directly to the PLL sections of the AVR for high speed
  78. # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  79. # at the end, this will be done automatically to create a 32-bit value in your
  80. # source code.
  81. #
  82. # If no clock division is performed on the input clock inside the AVR (via the
  83. # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
  84. F_USB = $(F_CPU)
  85. # Interrupt driven control endpoint task
  86. #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
  87. # Boot Section Size in *bytes*
  88. # Teensy halfKay 512
  89. # Teensy++ halfKay 1024
  90. # Atmel DFU loader 4096 (TMK Alt Controller)
  91. # LUFA bootloader 4096
  92. # USBaspLoader 2048
  93. OPT_DEFS += -DBOOTLOADER_SIZE=4096
  94. # Build Options
  95. # comment out to disable the options.
  96. #
  97. BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration
  98. MOUSEKEY_ENABLE = yes # Mouse keys
  99. EXTRAKEY_ENABLE = yes # Audio control and System control
  100. CONSOLE_ENABLE = yes # Console for debug
  101. COMMAND_ENABLE = yes # Commands for debug and configuration
  102. NKRO_ENABLE = yes # USB Nkey Rollover
  103. #KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
  104. #HHKB_JP = yes # HHKB JP support
  105. #OPT_DEFS += -DNO_ACTION_TAPPING
  106. #OPT_DEFS += -DNO_ACTION_LAYER
  107. #OPT_DEFS += -DNO_ACTION_MACRO
  108. #
  109. # Keymap file
  110. #
  111. ifdef KEYMAP
  112. SRC := keymap_$(KEYMAP).c $(SRC)
  113. else
  114. ifdef HHKB_JP
  115. SRC := keymap_jp.c $(SRC)
  116. else
  117. SRC := keymap_hhkb.c $(SRC)
  118. endif
  119. endif
  120. ifneq (, $(or $(findstring keymap_jp.c, $(SRC)), $(findstring yes, $(HHKB_JP))))
  121. OPT_DEFS += -DHHKB_JP
  122. endif
  123. # Search Path
  124. VPATH += $(TARGET_DIR)
  125. VPATH += $(TMK_DIR)
  126. include $(TMK_DIR)/protocol/lufa.mk
  127. include $(TMK_DIR)/common.mk
  128. include $(TMK_DIR)/rules.mk
  129. debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
  130. debug-on: all
  131. debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
  132. debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))
  133. debug-off: all