|
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186 |
- #----------------------------------------------------------------------------
- # On command line:
- #
- # make all = Make software.
- #
- # make clean = Clean out built project files.
- #
- # make coff = Convert ELF to AVR COFF.
- #
- # make extcoff = Convert ELF to AVR Extended COFF.
- #
- # make program = Download the hex file to the device.
- # Please customize your programmer settings(PROGRAM_CMD)
- #
- # make teensy = Download the hex file to the device, using teensy_loader_cli.
- # (must have teensy_loader_cli installed).
- #
- # make dfu = Download the hex file to the device, using dfu-programmer (must
- # have dfu-programmer installed).
- #
- # make flip = Download the hex file to the device, using Atmel FLIP (must
- # have Atmel FLIP installed).
- #
- # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
- # (must have dfu-programmer installed).
- #
- # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
- # (must have Atmel FLIP installed).
- #
- # make debug = Start either simulavr or avarice as specified for debugging,
- # with avr-gdb or avr-insight as the front end for debugging.
- #
- # make filename.s = Just compile filename.c into the assembler code only.
- #
- # make filename.i = Create a preprocessed source file for use in submitting
- # bug reports to the GCC project.
- #
- # To rebuild project do "make clean" then "make all".
- #----------------------------------------------------------------------------
-
- # Target file name (without extension).
- TARGET = tv44
-
- # Directory common source filess exist
- TOP_DIR = ../..
- TMK_DIR = ../../tmk_core
-
- # Directory keyboard dependent files exist
- TARGET_DIR = .
-
- # # project specific files
- SRC = tv44.c backlight.c
-
- ifdef keymap
- KEYMAP = $(keymap)
- endif
-
- ifdef KEYMAP
- ifneq ("$(wildcard keymaps/$(KEYMAP).c)","")
- KEYMAP_FILE = keymaps/$(KEYMAP).c
- else
- ifneq ("$(wildcard keymaps/$(KEYMAP)/keymap.c)","")
- KEYMAP_FILE = keymaps/$(KEYMAP)/keymap.c
- ifneq ("$(wildcard keymaps/$(KEYMAP)/makefile.mk)","")
- include keymaps/$(KEYMAP)/makefile.mk
- endif
- else
- $(error Keymap file does not exist)
- endif
- endif
-
- else
-
- ifneq ("$(wildcard keymaps/default.c)","")
- KEYMAP_FILE = keymaps/default.c
- else
- KEYMAP_FILE = keymaps/default/keymap.c
- endif
-
- ifneq ("$(wildcard keymaps/default/makefile.mk)","")
- include keymaps/default/makefile.mk
- endif
-
- endif
-
- SRC := $(KEYMAP_FILE) $(SRC)
-
- CONFIG_H = config.h
-
- # MCU name
- #MCU = at90usb1287
- MCU = atmega32u4
-
- # Processor frequency.
- # This will define a symbol, F_CPU, in all source code files equal to the
- # processor frequency in Hz. You can then use this symbol in your source code to
- # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
- # automatically to create a 32-bit value in your source code.
- #
- # This will be an integer division of F_USB below, as it is sourced by
- # F_USB after it has run through any CPU prescalers. Note that this value
- # does not *change* the processor frequency - it should merely be updated to
- # reflect the processor speed set externally so that the code can use accurate
- # software delays.
- F_CPU = 16000000
-
- #
- # LUFA specific
- #
- # Target architecture (see library "Board Types" documentation).
- ARCH = AVR8
-
- # Input clock frequency.
- # This will define a symbol, F_USB, in all source code files equal to the
- # input clock frequency (before any prescaling is performed) in Hz. This value may
- # differ from F_CPU if prescaling is used on the latter, and is required as the
- # raw input clock is fed directly to the PLL sections of the AVR for high speed
- # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
- # at the end, this will be done automatically to create a 32-bit value in your
- # source code.
- #
- # If no clock division is performed on the input clock inside the AVR (via the
- # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
- F_USB = $(F_CPU)
-
- # Interrupt driven control endpoint task(+60)
- OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
- # Boot Section Size in *bytes*
- # Teensy halfKay 512
- # Teensy++ halfKay 1024
- # Atmel DFU loader 4096
- # LUFA bootloader 4096
- # USBaspLoader 2048
- OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
- # Build Options
- # change to "no" to disable the options, or define them in the makefile.mk in
- # the appropriate keymap folder that will get included automatically
- #
- BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
- MOUSEKEY_ENABLE = no # Mouse keys(+4700)
- EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
- CONSOLE_ENABLE = no # Console for debug(+400)
- COMMAND_ENABLE = yes # Commands for debug and configuration
- NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
- BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
- MIDI_ENABLE = no # MIDI controls
- AUDIO_ENABLE = no # Audio output on port C6
- UNICODE_ENABLE = no # Unicode
- BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
- RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
-
- # Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
- SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
-
- ifdef KEYMAP
-
- ifeq ("$(wildcard keymaps/$(KEYMAP).c)","")
- ifneq ("$(wildcard keymaps/$(KEYMAP)/makefile.mk)","")
- include keymaps/$(KEYMAP)/makefile.mk
- endif
- endif
-
- else
-
- ifneq ("$(wildcard keymaps/default/makefile.mk)","")
- include keymaps/default/makefile.mk
- endif
-
- endif
-
- ifeq ($(strip $(BACKLIGHT_ENABLE)), yes)
- SRC := backlight.c $(SRC)
- endif
-
- # Optimize size but this may cause error "relocation truncated to fit"
- #EXTRALDFLAGS = -Wl,--relax
-
- # Search Path
- VPATH += $(TARGET_DIR)
- VPATH += $(TOP_DIR)
- VPATH += $(TMK_DIR)
-
- include $(TOP_DIR)/quantum/quantum.mk
|