|
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116 |
- # Target file name (without extension).
- TARGET ?= ps2_usb
-
- # Directory common source filess exist
- TMK_DIR ?= ../../tmk_core
-
- # Directory keyboard dependent files exist
- TARGET_DIR ?= .
-
- # project specific files
- SRC ?= matrix.c \
- led.c
-
- #
- # Keymap file
- #
- ifdef UNIMAP_ENABLE
- KEYMAP_FILE = unimap
- else
- ifdef ACTIONMAP_ENABLE
- KEYMAP_FILE = actionmap
- else
- KEYMAP_FILE = keymap
- endif
- endif
- ifdef KEYMAP
- SRC := $(KEYMAP_FILE)_$(KEYMAP).c $(SRC)
- else
- SRC := $(KEYMAP_FILE)_plain.c $(SRC)
- endif
-
- CONFIG_H ?= config.h
-
-
- # MCU name
- MCU ?= atmega32u2
-
- # Processor frequency.
- # This will define a symbol, F_CPU, in all source code files equal to the
- # processor frequency in Hz. You can then use this symbol in your source code to
- # calculate timings. Do NOT tack on a 'UL' at the end, this will be done
- # automatically to create a 32-bit value in your source code.
- #
- # This will be an integer division of F_USB below, as it is sourced by
- # F_USB after it has run through any CPU prescalers. Note that this value
- # does not *change* the processor frequency - it should merely be updated to
- # reflect the processor speed set externally so that the code can use accurate
- # software delays.
- F_CPU ?= 16000000
-
-
- #
- # LUFA specific
- #
- # Target architecture (see library "Board Types" documentation).
- ARCH ?= AVR8
-
- # Input clock frequency.
- # This will define a symbol, F_USB, in all source code files equal to the
- # input clock frequency (before any prescaling is performed) in Hz. This value may
- # differ from F_CPU if prescaling is used on the latter, and is required as the
- # raw input clock is fed directly to the PLL sections of the AVR for high speed
- # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
- # at the end, this will be done automatically to create a 32-bit value in your
- # source code.
- #
- # If no clock division is performed on the input clock inside the AVR (via the
- # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
- F_USB ?= $(F_CPU)
-
- # Interrupt driven control endpoint task
- # Not work with suart debug
- #OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
- # This improves response of keyboard when wakeup
- OPT_DEFS += -DSUSPEND_MODE_STANDBY
-
- # Boot Section Size in *bytes*
- # Teensy halfKay 512
- # Teensy++ halfKay 1024
- # Atmel DFU loader 4096
- # LUFA bootloader 4096
- # USBaspLoader 2048
- BOOTLOADER_SIZE ?= 4096
- OPT_DEFS += -DBOOTLOADER_SIZE=$(BOOTLOADER_SIZE)
-
-
- # Build Options
- # comment out to disable the options.
- #
- BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
- MOUSEKEY_ENABLE ?= no # Mouse keys(+4700)
- EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
- CONSOLE_ENABLE ?= yes # Console for debug(+400)
- COMMAND_ENABLE ?= yes # Commands for debug and configuration
- NKRO_ENABLE ?= yes # USB Nkey Rollover
-
-
- # PS/2 Options
- #
- #PS2_USE_USART ?= yes # uses hardware USART engine for PS/2 signal receive(recomened)
- PS2_USE_INT ?= yes # uses external interrupt for falling edge of PS/2 clock pin
- #PS2_USE_BUSYWAIT ?= yes # uses primitive reference code
-
-
- # Optimize size but this may cause error "relocation truncated to fit"
- #EXTRALDFLAGS = -Wl,--relax
-
- # Search Path
- VPATH += $(TARGET_DIR)
- VPATH += $(TMK_DIR)
-
- include $(TMK_DIR)/protocol.mk
- include $(TMK_DIR)/protocol/lufa.mk
- include $(TMK_DIR)/common.mk
- include $(TMK_DIR)/rules.mk
|