USB - General
- Refactored descriptors
- Enabled/Disable USB endpoints
- Added debug flags for special features
- Code cleanup
- Interface count calculation based off of enabled endpoints
- Delayed wTotalLength calculation to simplify descriptor offsets
- Re-ordered endpoints and interfaces
- Added more debug output
- Added usbInitTime to show how long keyboard initialization took
  (Useful when debugging bad init sequences)
- Added function for usb_resume() which takes care of the resume sequence
  * Resume is now only called if packets are starting to timeout

USB - Special Options
- Added enableDeviceRestartOnUSBTimeout
  * A last resort hammer for bad USB Chipsets/OSs, don't use if you can help it
  * Disabled
- Added enableUSBResume
  * Enables host resume wake-up signalling, required to wake a computer from sleep
  * Enabled
- Added enableUSBLowPowerNegotiation
  * Enables power negotiation hack
  * Required to use firmware with an IPad and other hard-limit low-power USB hosts
  * Hasn't been tested with the recent changes
  * Disabled
- Added enableUSBSuspend
  * Enables power down events on host USB bus suspend
  * Enabled

USB - Keyboard
- Attempted to cleanup HID SET_REPORT
  * Works much better
  * Still has an issue under Linux which generates *a lot* of NAKs (initializes quickly regardless)
    + Not present on other keyboards
    + SETUP -> OUT -> IN : This sequence is the problem
    + Specifically during the OUT phase
- Enabled

USB - CDC Virtual Serial Port
- Code cleanup
- Added convenience struct USBCDCLineCoding for easier debugging
- Attempted to cleanup CDC_SET_LING_CODING
  * Works much better
  * Still has an issue under Linux which generates *a lot* of NAKs (initializes quickly regardless)
    + SETUP -> OUT -> IN : This sequence is the problem
    + Specifically during the OUT phase
    + Likely the same issues as HID SET_REPORT
- Enabled

USB - Mouse
- Enabled

USB - Joystick
- Disabled

USB - RawIO
- Initial code, API not used yet
- Disabled

DFU
- Updated load script, now faster

- Somewhat aggresive, may cause restarts if the keyboard/OS hasn't fully intialized the keyboard
- Added GET_IDLE handling and correct usage of SET_IDLE
- Initial implementation of idle send, commented out as it causes issues on Mac OSX for sleeping
  (keyboard has been working without it)
- MacOSX seems to have some sort of data corruption on the USB link, not sure why (other OSs have no issues)
- Cleaned up some code
- Added a longer sleep after the resume sequence to prevent possible issues sending keys too soon
  (may need to be increased more)

Ipad support now seems flaky, though Mac, Windows seems solid.
Init sequence on Linux seems slow, even though there are no errors.

- Maintains a sleep state variable (may be able to use as a signal in the future)
- On the first keypress, hold the RESUME signal for 10 ms (spec says between 1 and 15 ms)
- Removed some messages that were affecting sleep state

- Odd that this went unnoticed for sooooo long
- Fixes Mac OSX issue where keyboard freezes/hangs on a reboot
- Also adding missing code for usbMuxUart

- Each scan module now has a current change callback which passes the available current as a parameter
- No longer attempts to use the max 500 mA immediately, starts with 100 mA then goes to 500 mA after enumeration
- If enumeration fails due to bMaxPower of 500 mA, then attempt again at 100 mA (might also be possible to go even lower to 20 mA in certain cases)
- Now working with the Apple Ipad (no over-power messages)
- Fixed Wake-up behaviour on Apple Ipad (and likely other iOS devices)
- More effecient set_feature/clear_feature handling (device handler)
- Initial power handling via Interconnect (still needs work to get it more dynamic)

- Now enabled by default
- Added protection around remote jumps

- Adds proper flashMode support for all keyboards and microcontrollers (usb and serial)
- flashModeEnabled must be set to 1 otherwise it will only show an error
  * This is on purpose (somewhat dangerous feature as it allows remote flashing)
- Capability cleanup

- Fixed cli reflash mode set
- Cleaned up debugging code
- 4 500 000 baud seems to be reliable
- Fixed master selection (assumes slave node unless USB enumerates)

- Changing header file ifndef define to pragma once's
- Removed duplicate output_com.h's

- Interrupt vector table position fix (affected everything in the firmware)
- Added fault debug messages
- Fixed usbMuxUart

Forgot to pull some files. Fixed those up too.

Use a consistent standard - Tabs in front for indenting, spaces after for anything else. This way everything stays nice and lined up while also letting users change there prefered indent level. Most of the new files from Haata where already in this format.

- Removing (currently) redundant usbMuxUart capabilities.kll file
- Issues were due to the recent AddModule cmake function addition

- Currently actual detection commented out due to issues

- Added AddModule CMake function which simplifies specifying module requirements

- Not ready yet
- Will require some more changes to Lib/mk20dx.c

- Also updating usbMuxUart header with most recent keyboard defines

- It's possible to get even more, but this is probably as far as I'll go
- PROGMEM is really annoying to use, and makes the code look like ass
- Now the Teensy 2++ should have enough RAM to use PartialMap easily

- Easier to debug USB initialization

- CLI now works with hex or decimal numbers
- Hex requires 0x (technically just x would work too)

- Changed static variables to const that should have been const
- Updated CMake files to prepare for MCHCK custom bootloader
- Changed the USB ID numbers and ID number for bootloader
- Only generate DFU or Teensy binary image, not both
- Fixed RAM and FLASH calculator
- Added missing license in delay.c/h (much of it was taken from Teensy source though I've changed a bunch of it)
- Prepared mk20dx.c for upcoming bootloader addition
- mk20dx.h cleanup
- Reduced the MCHCK based flash size for the application image (bootloader changes requires more flash space)
- Fixed bugs in macro.c
- Added keyHold cli command
- Added show pending events debug message for PartialMap macro module

- Cleaned up Macro and USB callback naming
- Added security jumper for automated reload (MCHCK based only)
- Added additional LED position

- McHCK uses FLL instead of the PLL for USB (startup, not usb init)
- Added optional debug for the pjrc USB module
- Cleaned up compiler flags

- Sending characters to the UART before it's ready would overflow the buffer causing it to hang
- Added a check to make sure the interface is ready before starting to send characters
- Removed the incorrect check for the usbMuxUart to make sure usb is ready before sending over the uart

- The UART out may be useful for Bluetooth keyboards at some point