- Updated port switching pins (split USB and UART switching)
- Added basic support for 2nd i2c bus
- Updated key matrix
- Fixed udev rules
- Added missing register defines

- Each scan module now has a current change callback which passes the available current as a parameter
- No longer attempts to use the max 500 mA immediately, starts with 100 mA then goes to 500 mA after enumeration
- If enumeration fails due to bMaxPower of 500 mA, then attempt again at 100 mA (might also be possible to go even lower to 20 mA in certain cases)
- Now working with the Apple Ipad (no over-power messages)
- Fixed Wake-up behaviour on Apple Ipad (and likely other iOS devices)
- More effecient set_feature/clear_feature handling (device handler)
- Initial power handling via Interconnect (still needs work to get it more dynamic)

- Each scan module now has a current change callback which passes the available current as a parameter
- No longer attempts to use the max 500 mA immediately, starts with 100 mA then goes to 500 mA after enumeration
- If enumeration fails due to bMaxPower of 500 mA, then attempt again at 100 mA (might also be possible to go even lower to 20 mA in certain cases)
- Now working with the Apple Ipad (no over-power messages)
- Fixed Wake-up behaviour on Apple Ipad (and likely other iOS devices)
- More effecient set_feature/clear_feature handling (device handler)
- Initial power handling via Interconnect (still needs work to get it more dynamic)

- Now enabled by default
- Added protection around remote jumps

- Adds proper flashMode support for all keyboards and microcontrollers (usb and serial)
- flashModeEnabled must be set to 1 otherwise it will only show an error
  * This is on purpose (somewhat dangerous feature as it allows remote flashing)
- Capability cleanup

- Fixed cli reflash mode set
- Cleaned up debugging code
- 4 500 000 baud seems to be reliable
- Fixed master selection (assumes slave node unless USB enumerates)

- Changing header file ifndef define to pragma once's
- Removed duplicate output_com.h's

- Interrupt vector table position fix (affected everything in the firmware)
- Added fault debug messages
- Fixed usbMuxUart

Forgot to pull some files. Fixed those up too.

Use a consistent standard - Tabs in front for indenting, spaces after for anything else. This way everything stays nice and lined up while also letting users change there prefered indent level. Most of the new files from Haata where already in this format.

- Removing (currently) redundant usbMuxUart capabilities.kll file
- Issues were due to the recent AddModule cmake function addition

- Currently actual detection commented out due to issues

- Added AddModule CMake function which simplifies specifying module requirements

- Not ready yet
- Will require some more changes to Lib/mk20dx.c

- Also updating usbMuxUart header with most recent keyboard defines

- It's possible to get even more, but this is probably as far as I'll go
- PROGMEM is really annoying to use, and makes the code look like ass
- Now the Teensy 2++ should have enough RAM to use PartialMap easily

- Easier to debug USB initialization

- CLI now works with hex or decimal numbers
- Hex requires 0x (technically just x would work too)

- Changed static variables to const that should have been const
- Updated CMake files to prepare for MCHCK custom bootloader
- Changed the USB ID numbers and ID number for bootloader
- Only generate DFU or Teensy binary image, not both
- Fixed RAM and FLASH calculator
- Added missing license in delay.c/h (much of it was taken from Teensy source though I've changed a bunch of it)
- Prepared mk20dx.c for upcoming bootloader addition
- mk20dx.h cleanup
- Reduced the MCHCK based flash size for the application image (bootloader changes requires more flash space)
- Fixed bugs in macro.c
- Added keyHold cli command
- Added show pending events debug message for PartialMap macro module

- Cleaned up Macro and USB callback naming
- Added security jumper for automated reload (MCHCK based only)
- Added additional LED position

- McHCK uses FLL instead of the PLL for USB (startup, not usb init)
- Added optional debug for the pjrc USB module
- Cleaned up compiler flags

- Sending characters to the UART before it's ready would overflow the buffer causing it to hang
- Added a check to make sure the interface is ready before starting to send characters
- Removed the incorrect check for the usbMuxUart to make sure usb is ready before sending over the uart

- The UART out may be useful for Bluetooth keyboards at some point