By default:
DebounceThrottleDiv = 0;
This is the default infinity behaviour right now (may be changed in the future).

Increasing DebounceThrottleDiv will increase the scan rate divider.
DebounceThrottleDiv = 1; # Scans half as much
DebounceThrottleDiv = 2; # Scans a quarter as much
DebounceThrottleDiv = 3; # Scans an eigth as much
etc.

For ARM based uCs (like the Infinity) the maximum divider is 32.

Can be specified from any .kll file

DebounceDivThreshold = 0xFFFFFFFF
Sets to max debounce, default is 0xFFFF.
The 0xFFFFFFFF is about a 2x longer debounce
The max requires more ram (as it uses 32 bit variables instead of 16).

Added support for submodule capabilities files.

- Currently actual detection commented out due to issues

- Added AddModule CMake function which simplifies specifying module requirements

- Not ready yet
- Will require some more changes to Lib/mk20dx.c

Fix an off by one error causing most keys to be shifted one to the
right, due to the missing backslash (\) key in the top row.

Fix an off by one error causing most keys to be shifted one to the
right, due to the missing backslash (\) key in the top row.

- It's possible to get even more, but this is probably as far as I'll go
- PROGMEM is really annoying to use, and makes the code look like ass
- Now the Teensy 2++ should have enough RAM to use PartialMap easily

- Typing now works on the kishsaver (including modifiers)
- Still some issues with RAM usage when using more than the default layer

- Added layout files for 50 key and kishsaver
- Not yet working (some USB issues on AVR to debug)
- Fixed an OSX issue when building AVR
- Cleanup

- Automatically downloads the kll compiler if not found
- Added capability files to each of the module that currently have them
- Split modules.cmake so kll.cmake could influence build targets (also needs info from modules.cmake)
- Updated .gitignore for kll compiler directory
- Added documentation on how to manipulate layouts using CMakeLists.txt
- Cleanup of old layout files

- CLI now works with hex or decimal numbers
- Hex requires 0x (technically just x would work too)

- Changed static variables to const that should have been const
- Updated CMake files to prepare for MCHCK custom bootloader
- Changed the USB ID numbers and ID number for bootloader
- Only generate DFU or Teensy binary image, not both
- Fixed RAM and FLASH calculator
- Added missing license in delay.c/h (much of it was taken from Teensy source though I've changed a bunch of it)
- Prepared mk20dx.c for upcoming bootloader addition
- mk20dx.h cleanup
- Reduced the MCHCK based flash size for the application image (bootloader changes requires more flash space)
- Fixed bugs in macro.c
- Added keyHold cli command
- Added show pending events debug message for PartialMap macro module

- CLI Debugging options added
- Various bug fixes for the matrix scanning algorithm
- Changed debouncing algorithm

- Cleaned up Macro and USB callback naming
- Added security jumper for automated reload (MCHCK based only)
- Added additional LED position

- More keyboard layouts and enhancements to come :D

- More generous to keys, and should reject all test points.

- There are some bugs here:
  * Press/Release (this is a keymapping bug, has nothing to do with capsense press/release which is working)
  * Some keys give incorrect USB codes

Caveat: The problem is still there. When the averaging kicks in, there is a window of time where keypresses won't register
        This fix only delays the window a *really* long time, so the likelihood of hitting the delay is very low.
	Each keypress resets the countdown.

- Should be tested more on keyboards without test points (to see if more of a margin in necessary)
- Added more information messages on bootup

- This requires that no strobes are floating.
  On Rev. 0.4, pins D1 and D0 of the teensy must be manually connected to GND
  On Rev. 0.2, when not using the 18 pin connector, pin C6 and C7 must be manually connected to GND
- Added a problem keys cli command, this is very useful to see which keys were disabled at startup because they looked like test points
  (the fastest way to get the keys to re-enable is to take off a keycap and jiggle the spring)

- Removed 'Zombie' code
- Still a bit of iffiness with the averaging algorithm (should be looked at again)
- Added more CLI debugging (averaging and press/debounce)

- Tried to add auto cmake reset...so far unsuccessful
- Ported MBC-55X (was used to test compilers)
- Disabled in-source builds, to prevent CMake from shooting itself in the foot.

- Strobe lines for IBM 50key
- Added CLI debugging for DPH, both per press and overall sense table
- Code cleanup (mostly just removal)

- To use the second ADC just specify ADC2 for all the commands.

- Vref of 1.2 V isn't working (may be due to missing setup/hardware)

- Mostly for reference, you shouldn't include it verbatim in your module.

- Code should be working, but much is untested
- All of the old modules will need to update and use the new DefaultMap keymap
- There might still be some naming conflicts with some Scan Modules

- Includes serial putchar and getchar cleanup (overall)
- Moved avr-capsense to DPH (renaming)
- Basic cleanup for including CLI on the avr architecture

- Any keys that exceed the high average are temporarily disabled
- If the sense value goes below the initial average sense, it is re-enabled
- Even works if *many* keys are pressed initially

- Still needs a bit of detection of consistent high keys that sometimes sneak below the threshold
  (May be able to have an elastic threshold that could deal with this)

- Removed dead code (and redundant calculations)

- Enabling the test point strobe on the kishsaver really kills the sensing (many keys don't work, even at 400)

- Should fix the last of the phantom keys

- Not confirmed that this fixes all known phantom keypresses

- Added debounce mechanism, currently looks for 5 consecutive scans
- Temporarily disabled the test point strobe on the kishsaver (spams debug messages, and not useful anymore; needs to be addressed before strobe detection is implemented though)
- Reorganized code to cleanup the main scan loop function