- Includes pixel testing functions

- Includes basic (led) channel testing tools
- Currently hard-coded, needs kll integration before this can be used in general

- Added port swapping to KType
- Added initial KType default keymappings
- Initial PixelMap animiation framework
- Swapped in new i2c library for ISSILed

- Works the same as the bootloader variant, waits 1000 ms before attempting to swap
  Only swaps if USB not already intialized
  If USB never initializes, will swap forever

TODO
- Stop swapping if UARTConnect detected and initialized

- Basic support for up to 4 ISSI chips (and partial support for 16 chip configurations)
- Initial USB mux support
  * Required USB re-init procedure
- Initial interconnect mux support
  * Required some state reset commands

- Basic support for up to 4 ISSI chips (and partial support for 16 chip configurations)
- Initial USB mux support
  * Required USB re-init procedure
- Initial interconnect mux support
  * Required some state reset commands

The example scripts include hardcoded values that
do not work for everyone. Instead of requiring the
files to be edited (and dirtying the git tree),
allow them to take command-line arguments.

Also adds better guidance for Mac OSX virtual
serial ports.

bash might not be in /bin. Don't expect it there.

- Works for all nodes in chain
- Synchronized to 30 ms update rate (required for ISSI chip)
  * Interconnect cannot handle full update speed from Scan module
  * Though it should be able to handle quite a bit more than 30 ms updates

- Rx buffers weren't fast enough, had to use DMA :D
- Basic LCD remote capabilities are working, single node
- Multi-node broadcast seems to have a bug still
- DMA ring buffer allowed for significant processing simplification
  * There is an overrun risk, but the buffer is large and generally there isn't too much data being sent (just very quickly)
- Split out LCD layer stack capability into itself and an "exact" version used for updating remote nodes

- 6 modes
  * Single led: decrease, increase, set
  * All leds: decrease, increase, set
- Currently update speed limited to once every 30 ms
  * Likely an I2C driver or ISSI limitation preventing even faster updates

- Requires kll update
- Including udev id update

- Includes minor fix for MD1

- Adds proper flashMode support for all keyboards and microcontrollers (usb and serial)
- flashModeEnabled must be set to 1 otherwise it will only show an error
  * This is on purpose (somewhat dangerous feature as it allows remote flashing)
- Capability cleanup

- Requires lcdFuncMap.kll instead of stdFuncMap.kll

- See md1Action.kll for usage
- Includes Block/Unblock

- Includes fix for over-range ScanCodes (would cause hard faults)
- Updated some documentation
- Requires recent kll compiler for the layout

- Supports up to 255 slave nodes (you'll run into ScanCode limitations before then)
- Requires most recent kll compiler update
- Additional debugging output and stats counters
- Noise and parity checking
- Fixed TxFIFO issue when sending buffers larger than the FIFO
- Cleaned up defaultMap.kll
- Added ScanCode caching (reduces interconnect traffic significantly)
- Interconnect module code is conditionally compiled into PartialMap module if required

- Still some issues
- Will require some changes to MatrixARM and PartialMap
  * Currently state information is passed around too frequently
  * Needs to be reduced to state changes only

- Required updates to CMake in order to handle the multi-layer BaseMaps

- Adds override functionality in main module

- Fixed cli reflash mode set
- Cleaned up debugging code
- 4 500 000 baud seems to be reliable
- Fixed master selection (assumes slave node unless USB enumerates)

- Uses expiry timer to decide on when to allow a state change
- Initial state transitions are unaffected
- Use MinDebounceTime define in kll to configure
- ms granularity

- Changing header file ifndef define to pragma once's
- Removed duplicate output_com.h's

- Basic screen initialization and clear is working
- Currently SPI is set to a low speed for easy logic analyzer debugging

- Not ready for advanced support yet
- Basic register and page writing support complete

* Keyboard interconnect using two uarts
* Supports daisy chain addressing using a master/slave direction communication scheme

- Still needs more testing
- Functions have been tested alone to be generally working

Use a consistent standard - Tabs in front for indenting, spaces after for anything else. This way everything stays nice and lined up while also letting users change there prefered indent level. Most of the new files from Haata where already in this format.

By default:
DebounceThrottleDiv = 0;
This is the default infinity behaviour right now (may be changed in the future).

Increasing DebounceThrottleDiv will increase the scan rate divider.
DebounceThrottleDiv = 1; # Scans half as much
DebounceThrottleDiv = 2; # Scans a quarter as much
DebounceThrottleDiv = 3; # Scans an eigth as much
etc.

For ARM based uCs (like the Infinity) the maximum divider is 32.

Can be specified from any .kll file

DebounceDivThreshold = 0xFFFFFFFF
Sets to max debounce, default is 0xFFFF.
The 0xFFFFFFFF is about a 2x longer debounce
The max requires more ram (as it uses 32 bit variables instead of 16).

Added support for submodule capabilities files.

- Currently actual detection commented out due to issues